Andrea Rossi

Dr. Andrea Rossi

Roma TRE University, Department of Industrial, Electronic and Mechanical Engineering
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 April 2018 in Actuators
Verified
Journal Article
Open access
PDF file
ARAndrea Rossi
Andrea Rossi
FOFrancesco Orsini
Francesco Orsini
Andrea ScorzaAndrea Scorza
Andrea Scorza
FBFabio Botta
Fabio Botta
Nicola Pio BelfioreNicola Pio Belfiore
Nicola Pio Belfiore
SSSalvatore Andrea SCIUTO
Salvatore Andrea SCIUTO
Magnetorheological (MR) fluids are capable of manifesting a rheological behaviour change by means of a magnetic field application and can be employed in many complex systems in many technical fields. One successful example is their use in the development of dampers: magnetorheological dampers (MRDs) are widespread in vibration control systems, as well as civil engineering applications (i.e., earthquake or seismic protection), impact absorption and vibration isolation technology in industrial engineering, and advanced prosthetics in biomedical fields. In the past, many studies have been conducted on MRDs modeling and characterization, but they have usually been focused more on the theoretical models than on the experimental issues. In this work, an overview of both of them is proposed. In particular, after an introduction to the physics of the magnetorheological effect, a short review of the main mathematical models of MRDs is proposed. Finally, in the second part of this study an overview of the main issues that occur in MRDs experimental characterization is reported and discussed.

18 April 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ARAndrea Rossi
Andrea Rossi
Gabriele BocchettaGabriele Bocchetta
Gabriele Bocchetta
FBFabio Botta
Fabio Botta
Andrea ScorzaAndrea Scorza
Andrea Scorza
Active and passive vibration control systems are of paramount importance in many engineering applications. If an external load excites a structure’s resonance and the damping is too low, detrimental events, such as crack initiation, growth and, in the worst case, fatigue failure, can be entailed. Damping systems can be commonly found in applications such as industrial machines, vehicles, buildings, turbomachinery blades, and so forth. Active control systems usually achieve higher damping effectiveness than passive ones, but they need a sensor to detect the working conditions that require damping system activation. Recently, the development of such systems in rotating structures has received considerable interest among designers. As a result, the development of vibration monitoring equipment in rotating structures is also a topic of particular interest. In this respect, a reliable, inexpensive and wireless monitoring system is of utmost importance. Typically, optical systems are used to measure vibrations, but they are expensive and require rather complex processing algorithms. In this paper, a wireless system based on a commercial MEMS accelerometer is developed for rotating blade vibration monitoring. The proposed system measurement accuracy was assessed by means of comparison with a reference wired measurement setup based on a mini integrated circuit piezoelectric (ICP) accelerometer adapted for data acquisition in a rotating frame. Both the accelerometers were mounted on the tip of the blade and, in order to test the structure under different conditions, the first four blade resonances were excited by means of piezoelectric actuators, embedded in a novel experimental setup. The frequency and amplitude of acceleration, simultaneously measured by the reference and MEMS sensors, were compared with each other in order to investigate the viability and accuracy of the proposed wireless monitoring system. The rotor angular speed was varied from 0 to 300 rpm, and the data acquisitions were repeated six times for each considered condition. The outcomes reveal that the wireless measurement system may be successfully used for vibration monitoring in rotating blades.

1 October 2021 in Journal of Sound and Vibration
Verified
Journal Article
Closed access
FBFabio Botta
Fabio Botta
ARAndrea Rossi
Andrea Rossi
Nicola Pio BelfioreNicola Pio Belfiore
Nicola Pio Belfiore

17 October 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
Nicola Pio BelfioreNicola Pio Belfiore
Nicola Pio Belfiore
ABAlvise Bagolini
Alvise Bagolini
ARAndrea Rossi
Andrea Rossi
Gabriele BocchettaGabriele Bocchetta
Gabriele Bocchetta
FVFederica Vurchio
Federica Vurchio
SSSalvatore Andrea SCIUTO
Salvatore Andrea SCIUTO
This paper presents the development of a new microgripper actuated by means of rotary-comb drives equipped with two cooperating fingers arrays. The microsystem presents eight CSFH flexures (Conjugate Surface Flexure Hinge) that allow the designer to assign a prescribed motion to the gripping tips. In fact, the adoption of multiple CSFHs gives rise to the possibility of embedding quite a complex mechanical structure and, therefore, increasing the number of design parameters. For the case under study, a double four-bar linkage in a mirroring configuration was adopted. The presented microgripper has been fabricated by using a hard metal mask on a Silicon-on-Insulator (SOI) wafer, subject to DRIE (Deep Reactive Ion Etching) process, with a vapor releasing final stage. Some prototypes have been obtained and then tested in a lab. Finally, the experimental results have been used in order to assess simulation tools that can be used to minimize the amount of expensive equipment in operational environments.

3 April 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
FBFabio Botta
Fabio Botta
Andrea ScorzaAndrea Scorza
Andrea Scorza
ARAndrea Rossi
Andrea Rossi
Vibration damping is prominent in engineering; in fact, vibrations are related to many phenomena (e.g., the fatigue of structural elements). The advent of smart materials has significantly increased the number of available solutions in this field. Among smart materials, piezoelectric materials are most promising. However, their efficiency depends on their placement. There are many studies on their optimal placement for damping a particular mode, but few account for multimodal vibrations damping. In a previous work, an analytical method was proposed to find the optimal placement of piezoelectric plates to control the multimode vibrations of a cantilever beam. In this study, the efficiency of the above method has been improved, considering all plates active simultaneously, regardless of the eigenmodes that are excited, and changing, instead of the plates, the potential distribution. The method results indicate the optimal potential distribution for different excited eigenmodes. The results have been compared with those obtained by experimental tests and numerical simulations, exhibiting very good agreement.

25 February 2022 in Actuators
Verified
Journal Article
Open access
PDF file
Alessio BuzzinAlessio Buzzin
Alessio Buzzin
ARAndrea Rossi
Andrea Rossi
EGEnnio Giovine
Ennio Giovine
Giampiero de CesareGiampiero de Cesare
Giampiero de Cesare
Nicola Pio BelfioreNicola Pio Belfiore
Nicola Pio Belfiore
Downscaling has been a focal task of Electronics and Electromechanics in the last few decades, and a great engine for technological progress as well. Nevertheless, a scaling operation affects device physics, functioning and performance. The present paper investigates about the impact of scaling on a test case compliant electrostatic micro or nano actuator that is under development with two preferred micro fabrication methods, namely, thick SOI and thin amorphous silicon. A series of numerical trials on materials strength, electro-mechanical characteristics, sensitivity and overall actuation performance have been carried out at different grades of down-scaling and of aspect ratio. This gave rise to new design charts that we propose here as a predictive and friendly guide to select the most appropriate micro fabrication method.