This article presents a color light detection system integrated in 130 nm CMOS technology. The sensors and corresponding electronics detect light in a CIE XYZ color luminosity space using on-chip integrated sensors without any additional process steps, high-resolution analog-to-digital converter, and dedicated DSP algorithm. The sensor consists of a set of laterally arranged integrated photodiodes that are partly covered by metal, where color separation between the photodiodes is achieved by lateral carrier diffusion together with wavelength-dependent absorption. A high resolution, hybrid, ∑∆ ADC converts each photo diode’s current into a 22-bit digital result, canceling the dark current of the photo diodes. The digital results are further processed by the DSP, which calculates normalized XYZ or RGB color and intensity parameters using linear transformations of the three photo diode responses by multiplication of the data with a transformation matrix, where the coefficients are extracted by training in combination with a pseudo-inverse operation and the least-mean square approximation. The sensor system detects the color light parameters with 22-bit accuracy, consumes less than 60 μA on average at 10 readings per second, and occupies approx. 0.8 mm2 of silicon area (including three photodiodes and the analog part of the ADC). The DSP is currently implemented on FPGA.
A high-speed full-duplex transceiver (FDT) over lossy on-chip interconnects is presented. The FDT employs a hybrid circuit to separate the inbound and outbound signals from each other and also performs echo-cancellation with the help of the main and the auxiliary drivers. A hybrid MOS device is utilized for impedance matching and conversion of the received voltage signal into a current signal for amplification. Moreover, a compensation capacitance ( ) is used at the output of the main driver to minimize the residual echo signal and achieve a higher data rate. The entire FDT architecture has been designed in TSMC 28 nm CMOS standard process with 0.9 V supply voltage. The performance results validate a 16 Gbps FD operation with a root-mean-square (RMS) jitter of 16.4 ps, and a power efficiency of 0.16 pJ/b/mm over a 5 mm on-chip interconnect without significant effect due to process-voltage-temperature (PVT) variations. To the best knowledge of the authors, this work shows the highest achievable full-duplex data rate, among the solutions reported in the literature to date, yet with low complexity, low layout area of 1581 and competitive power efficiency.
21 February 2018 in e+i Elektrotechnik und Informationstechnik
This article presents an overview of modern integration concepts for receiver, transmitter and duplexer architectures. Based on innovative design techniques, a system-in-package integrated RF transceiver architecture is proposed as a low-cost low-power alternative to traditional multi-standard transceivers. The proposed transceiver architecture unites advantages of a sub-sampling receiver with tunable low noise amplifier (LNA), a high-efficiency digital power amplifier and an integrated duplexer with on-package passive components in order to fulfill the more and more stringent requirements for wireless systems. In addition to the transceiver architecture, measurement results of building blocks are presented. A LNA circuit implemented in \(65~\text{nm}\) CMOS technology provides a continuously tunable-gain (3–23 dB) and a tunable frequency band (4.5 GHz–5.5 GHz) with noise figure of \(2~\text{dB}\) and IIP3 of \(-6.5~\text{dBm}\) at the highest gain. A high Q-factor, on-package transformer, implemented in a core-less 3-metal layer system-in-package substrate, presents a coupling factor of 0.6 and a Q-factor of approximately 30. This provides a low-cost, high-performance alternative solution to integrated matching networks and duplexers. Der folgende Artikel gibt einen Überblick über moderne Integrationskonzepte von Hochfrequenz-Transceivern, anhand von spezifischen Beispielen innovativer Empfänger, Sender und Duplexer-Architekturen. Das vorgestellte Konzept nutzt moderne System-in-Package-Technologien gemeinsam mit Chip-Integration als kostengünstige und energiesparende Alternative zu traditionellen Transceiver-Konzepten. Es vereint einen innovativen Sub-Sampling Receiver mit einem flexibel abstimmbaren Low-Noise Amplifier (LNA), einen effizienten digitalen Leistungsverstärker sowie einen passiven Duplexer, integriert in einer System-in-Package-Technologie. Ergänzend zur Transceiver-Architektur wird die Schaltungsrealisierung des LNA mit kontinuierlich verstellbarer Verstärkung von 3 dB bis 23 dB, einer verstellbaren Frequenz von 4.5 GHz bis 5.5 GHz, einer Noise Figure von 2 dB und einer IIP3-Linearität von −6.5 dBm bei höchster Verstärkung präsentiert. Weiters wird ein hochqualitativer Transformator vorgestellt, welcher durch Nutzung einer dreilagigen System-in-Package-Technologie realisiert wurde und einen Qualitätsfaktor von 30 sowie einen Kopplungsfaktor von 0.6 aufweist.
A bi-directional active resistor structure with quasifloating gate MOS transistors and non-linearity compensation is used in a resistive negative feedback wide-band LNA implementation enabling a continuously tunable gain from 0dB to 24dB. The LNA has been realized in 65nm CMOS with a minimum noise figure of 2.5dB and IIP3 of -8dBm at highest gain. The LNA bandwidth is from 100MHz to 2GHz, with a power consumption of 12mW and an active area of 0.0375mm 2 .
Nowadays, the need for safe human-robot-co-existence has become increasingly important. Therefore, the requirement to faithful detection of persons in the work arena of a robot is a prime concern to ensure human-safety. Capacitance based proximity sensors system is presented to measure the presence of objects and, hence, allow the detection of proximity of persons, enabling human robot collaboration. This paper presents the techniques for sensing tiny capacitance variations due to approaching objects among the presence of large parasitic capacitances. We also introduced a commn-mode (CM) compen-satory branch to reject rail-to-rail common-mode interference. In addition, we proposed the offset tolerant amplifier with the characteristics of low noise, high gain and wide-band operation. The proposed topology is designed, simulated and verified in 65 nm standard CMOS process.