This paper outlines the design and validation of a four-port compact Multi-Input Multi-Output (MIMO) antenna engineered to provide reconfigurable band notches within the ultra-wideband spectrum. The antenna features a circular monopole engraved with split ring slots along its radiating section, while a U-shaped slot is etched onto the feed line to facilitate band notches at specific frequencies—4.3 GHz (corresponding to INSAT), 6.8 GHz (aligned with Wi-Fi-6E), and 8.3 GHz (pertaining to X-band satellite). To ensure proper isolation, the MIMO elements are arranged orthogonally, and a decoupling periodic structure is strategically interposed between these elements to enhance isolation further. The incorporation of a PIN diode within the U-shaped slot introduces reconfigurability into the band notching mechanism. The MIMO antenna operates in two distinct modes depending upon the state of the PIN diode, either activated (ON) or deactivated (OFF). In the former mode, the antenna offers switchable band notches across three frequencies, while in the latter mode, it offers band notches at two specific frequencies. The validity of the antenna’s performance is validated through real-time fabrication and measurement. Both simulated and measured results exhibit a notable correlation. The antenna stands as an appropriate candidate for future cognitive radio applications.
In modern ICs, sub-threshold voltage management plays a significant role due to its perspective on energy efficiency and speed performance. Level shifters (LSs) play a critical role in signal exchange among multiple voltage domains by ensuring signal integrity and the reliable operation of ICs. In this article, a Pass-Transistor-Enabled Split Input Voltage Level Shifter (PVLS) is designed for area, delay, and power-efficient applications with a wide voltage conversion range. The represented low-power LS structure is a general blend of both pull-up and pull-down networks that perform level-up or level-down shifts. The proposed PVLS is incorporated with the multi-threshold CMOS technique and a load-balancing driving split inverter to limit high static current, leakage power, and performance degradation. The schematic structure could be able to convert voltages from low to high as well as high to low. The architecture design has the lowest silicon area. The implementation of the proposed design was taken under 55 nm CMOS technology. The represented LS could be able to convert voltage ranges between 0.3 V and 1.3 V, which has a dynamic power of 2.00 nW. The overall propagation delay of the LS is 90 ps and an area of 7.66 µm2 for an input frequency of 1 MHz.
1 April 2025 in International Journal of Electrical and Computer Engineering (IJECE)
The focus on power optimization in embedded systems is especially important for embedded applications since it has brought in many methods and factors that are necessary for developing systems that are both power- and area-efficient. In contrast to the current delayed wavelet μ-law proportionate least mean square (DWMPLMS) and delayed least mean square (DLMS) algorithms, this work offers the development of adaptive filters based on the least mean square (LMS) method, which improves power and timing performance. In order to improve area and time efficiency, the proportionate least mean square (PLMS) algorithm's architecture has been modified to remove delay, add a proportionate gain block, design for a fixed length, include an approximate multiplier block, and swap out standard blocks for floating-point adder and divider blocks. According to a power and temporal comparison with the DWMPLMS and DLMS algorithms, field-programmable gate array (FPGA) synthesis reduces power usage by 95% for a 32-bit filter length in PLMS when compared to the above methods.
12 November 2026 in Journal of Circuits, Systems and Computers
This paper presents a triple-band planar antenna with diverse radiation patterns. The proposed planar antenna is a modified swastika shape with three fingers and the ground plane is a circle with rectangular slots etched on four sides radially. The slotted ground plane is loaded with Four PIN diodes to realign the surface current. Pattern reconfigurability is achieved at the triple bands by changing the states of the diode. The antenna operates in triple bands centered at 2.2, 2.9 and 3.5 GHz. The antenna is printed on FR4 Epoxy substrate. The simulated reflection coefficient is well below −10dB at resonant frequencies. The measured patterns and return loss are in very close agreement with the simulated results. This antenna can find potential applications in 5G systems.