The operational energy efficiency of new buildings in the EU should be at the level of ultra-low or near-zero energy buildings. It is therefore relatively difficult to achieve further energy savings. However, the pre-operational phase—raw material sourcing, manufacturing, transportation, and construction—offers significant energy savings and greenhouse gas reduction opportunities, referred to as embodied energy and equivalent CO2 emissions. Unlike operational energy, no standard or legislative criteria have yet been established for embodied energy. Setting maximum embodied energy values converted to the unit of heated building area, accounting for building shape factor, and differentiating between high-mass and lightweight constructions are proposed. This study illustrates assessing environmental indicators based on building shape, highlighting the necessity of relative assessments over absolute values to favour energy efficiency. It also emphasizes that precise criteria should derive from authentic data collected during the energy certification and building permitting processes. Integrating assessments of embodied energy and operational energy demand facilitates a comprehensive evaluation of buildings’ environmental performance.
30 July 2019 in Eastern-European Journal of Enterprise Technologies
Problem statement. Cross-laminated timber (CLT) is a modern building material that can be used in the construction of buildings for various purposes. Despite its popularity abroad, CLT is still a relatively new material in Ukraine, and the current standards for designing timber structures do not include recommendations for the calculation of structures made from CLT panels. To promote the use of CLT in domestic practice, it is necessary to conduct studies on its strength characteristics in accordance with international standards. The purpose of the article is to investigate the characteristics of bending and compressive strength of domestically produced CLT through tests according to European standards. Methods. For experimental studies, samples of elements from the CLT-Result domestic manufacturer were used. The samples consisted of coniferous lumber (pine Pinus sylvestris I.) in a configuration of 3 layers 30 mm thick (CLT thickness 90 mm) and 5 layers 20 mm thick (CLT thickness 100 mm). Bending and compression tests were performed parallel and perpendicular to the plane of the longitudinal layers in accordance with the requirements of EN 16351:2021 and EN 408:2012. Conclusion. The bending strength of CLT samples is determined by the strength of the timber of the outer, most stretched layer. The destruction of the samples during bending began with the formation of cracks along the annual rings of the wood of the outer lower layer, followed by the rupture of the stretched fibers. CLT samples, when tested for compression parallel to the plane of the layers, collapsed due to the exhaustion of the bearing capacity of the timber of the longitudinal layers, which was accompanied by shearing along the inclined areas. The destruction of the CLT compressed perpendicular to the plane of the layers occurred as a result of significant compression of the wood. The following characteristics were determined: the bending strength of the 3-layer CLT panel was 15.3 MPa, and the 5-layer panel had a bending strength of 20.1 MPa; the compressive strength of the 5-layer CLT panel parallel to the plane of the layers fc,0 = 26.88…29.15 MPa, and perpendicular to the plane of the layers fc,90 = 11.16...12.13 MPa.
The current trend in the construction industry is the development of projects of multi-storey buildings with a hybrid structural system using mainly timber load-bearing elements. The joints of load-bearing elements are criti-cal points of the frame with glued timber structures in terms of ensuring the load-bearing capacity and servicea-bility of the entire system. Existing publications in this area are mainly aimed at theoretical and experimental as-sessment of the stress-strain state of joints, while information on the construction of components for multi-storey buildings and recommendations for their design is extremely insufficient. The article presents structural solutions of the joints of glued laminated timber columns and beams, namely, hinged, which takes and transmits to the col-umn the support reaction of the beam, and rigid, which in addition to the support reaction takes the bending mo-ment. The support reaction from the beam to the column is transferred through a bolted connection and a T-shaped welded metal element. The bending moment is taken by two angles, which are fixed to the beam and welded to a vertical plate. Criteria of conformity of the proposed joints to load-bearing capacity requirements are pro-posed. The load-bearing capacity of the joint under the action of the support shear force is determined by the shear strength of the bolts in the column; the embedment strength of the metal of the T-shaped plate in the hole and bearing capacity of the bolted connection in the timber element. The action of the support bending moment requires the strength of the angles fastening to the beam and wood in the area of the bolts installation. A detailed algorithm for calculating the proposed design solutions in accordance with the requirements of the design stand-ards has been developed. Keywords: joint, glued laminated timber, beam, column, bearing capacity.
29 November 2021 in Building constructions. Theory and Practice
The construction industry is the main consumer of natural resources, characterized by significant consumption of non-renewable resources and the impact on environmental pollution. Up to 50% of carbon dioxide emissions are accounted for by the construction industry. In addition, the main feature of the traditional construction industry is the overuse of energy, which affects the process of global warming and climate change. Energy is consumed in the extraction of raw materials, production and transportation of materials, in the process of construction, operation, repair and liquidation of buildings. Awareness of global environmental problems has led to a rethinking of the process of design, construction, operation and disposal of buildings in the European Union, the United States, Canada and others and the emergence of the concept of sustainable development and "green" construction. In this aspect, the main criteria for designing buildings are to minimize the impact on the environment, as well as reduce energy costs, reduce waste and harmful emissions. The solution of the above problems, taking into account national specifics, can be achieved by developing typical resource- and energy-efficient, cost-effective design solutions for load-bearing and enclosing elements and their joints using environmentally friendly materials of local origin (wood and materials based on it, clay materials, straw, reeds, etc.