Cortisol is a pivotal hormone regulating stress responses and is linked to various health conditions, making precise and continuous monitoring essential. Despite their non-invasive nature, conventional cortisol detection methods often suffer from inadequate sensitivity and reliability at low concentrations, limiting their diagnostic utility. To address these limitations, this study introduces a novel paradigm for high sensitivity cortisol detection using field-effect transistor (FET) sensors with dual-gate (DG) structures. The proposed sensor platform enhances sensitivity through capacitive coupling without requiring external circuits. Cortisol detection performance was evaluated by immobilizing monoclonal antibodies activated via 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide and N-hydroxysuccinimide onto a SnO2 thin film-based extended-gate. The results revealed a sensitivity of 14.3 mV/dec in single-gate mode, which significantly increased to 243.8 mV/dec in DG mode, achieving a detection limit of 276 pM. Additionally, the reliability and stability of the sensor were validated by evaluating drift effects, confirming its ability to provide accurate detection even in artificial saliva environments containing interfering substances. In conclusion, the DG-FET-based cortisol detection approach developed in this study significantly outperforms conventional FET-based methods, enabling precise monitoring at ultra-low concentrations. This approach holds significant potential for diverse bioassays requiring high sensitivity and reliability in complex environments.
In this study, we propose a bidirectional chemical sensor platform based on a reconfigurable ion-sensitive field-effect transistor (R-ISFET) architecture. The device incorporates Ni-silicide Schottky barrier source/drain (S/D) contacts, enabling ambipolar conduction and bidirectional turn-on behavior for both p-type and n-type configurations. Channel polarity is dynamically controlled via the program gate (PG), while the control gate (CG) suppresses leakage current, enhancing operational stability and energy efficiency. A dual-control-gate (DCG) structure enhances capacitive coupling, enabling sensitivity beyond the Nernst limit without external amplification. The extended-gate (EG) architecture physically separates the transistor and sensing regions, improving durability and long-term reliability. Electrical characteristics were evaluated through transfer and output curves, and carrier transport mechanisms were analyzed using band diagrams. Sensor performance—including sensitivity, hysteresis, and drift—was assessed under various pH conditions and external noise up to 5 Vpp (i.e., peak-to-peak voltage). The n-type configuration exhibited high mobility and fast response, while the p-type configuration demonstrated excellent noise immunity and low drift. Both modes showed consistent sensitivity trends, confirming the feasibility of complementary sensing. These results indicate that the proposed R-ISFET sensor enables selective mode switching for high sensitivity and robust operation, offering strong potential for next-generation biosensing and chemical detection.
1 June 2025 in Japanese Journal of Applied Physics
Lead zirconate titanate oxide (PZTO) thin films, fabricated via the sol-gel process, were studied as high-sensitivity pH-sensing membranes for ion-sensitive field-effect transistor (ISFET)-based biosensors. This study evaluated the surface and structural characteristics of PZTO membranes in their as-deposited state and after microwave annealing (MWA) at power levels (600, 1000, 1400, 1800 W). X-ray photoelectron spectroscopy (XPS), X-ray diffraction, and atomic force microscopy revealed that MWA significantly improved membrane properties by promoting Ti- and Zr-hydroxyl group formation, reducing surface roughness. The 1400 W MWA-treated PZTO membrane exhibited superior pH-sensing performance, achieving 56.9 mV pH−1 sensitivity, an 11.8 mV hysteresis voltage, and a 9.5 mV h−1 drift rate, outperforming the as-deposited membrane. These findings highlight MWA as an effective treatment for optimizing PZTO membranes and demonstrate its potential for ISFET-based biosensors in real-time, accurate pH detection. This study advances biosensor technology and provides a foundation for PZTO optimization.
Heterojunction engineering provides an effective route to modulate carrier transport and threshold voltage in amorphous oxide semiconductor thin-film transistors (TFTs); however, thermal processing can induce interfacial intermixing and defect redistribution, potentially obscuring the designed electronic structure. In this work, Al-doped In–Zn–Sn–O/Zn–Sn–O (AIZTO/ZTO) heterojunction channels were integrated with microwave annealing (MWA) to control the interfacial electronic structure and oxygen-related defect states while maintaining a low thermal budget. Optical and ultraviolet photoelectron spectroscopy revealed a conduction-band offset across the AIZTO/ZTO heterointerface, giving rise to a potential-well-like region that promotes interfacial carrier accumulation and transport. X-ray photoelectron spectroscopy, including depth profiling, further showed that MWA suppressed excessive cation intermixing and altered the distribution of oxygen-related bonding states across the heterointerface relative to conventional thermal annealing. Optimization of the AIZTO/ZTO thickness ratio further enabled simultaneous regulation of carrier transport and threshold voltage. The optimized microwave-annealed heterojunction TFT exhibited a near-zero threshold voltage of −0.38 V, together with a high linear field-effect mobility of 37.64 cm2 V−1 s−1 and a subthreshold swing of 202.09 mV dec−1. Furthermore, the device exhibited reduced threshold-voltage shifts of +0.52 and −1.59 V under positive and negative bias stress, respectively. These results demonstrate that microwave-controlled heterointerface engineering enables the coupled regulation of band alignment, oxygen-related defect states, and interfacial cation mixing, providing a materials-engineering strategy for mitigating the mobility–threshold-voltage–stability trade-off in oxide TFTs.