Shengnan Yuan

Ms. Shengnan Yuan

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 March 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
RWRongjun Wang
Rongjun Wang
QZQiang Zhang
Qiang Zhang
PZPengchong Zhang
Pengchong Zhang
XLXin Liu
Xin Liu
SYShengnan Yuan
Shengnan Yuan
LMLiFeng Ma
LiFeng Ma
Currently, magnesium alloys are extensively used owing to their excellent comprehensive mechanical properties. Rolling is a primary method used to produce magnesium alloy plates. However, so far, only few reports have been investigated about the straightening of rolled magnesium alloy plates. In this study, multi-roller straightening of the magnesium alloy plate is theoretically analyzed and simulated using the finite element method. Multi-roller straightening process of the magnesium alloy plate was performed as follows: the original bending curvature that exhibited large numerical differences in different directions was gradually reduced through reasonable distribution of the plastic deformation rate of each straightening roller system. Finite element simulation and experimental results are obtained for room-temperature magnesium alloy plate straightening at four different plastic deformation rates. However, the straightening effect is minimal when the micro plastic deformation rate is used for straightening the magnesium alloy plate with an initial curvature, this is because the reverse bending rate required for straightening is not attained. Straightening effect can be achieved with low, moderate, or high plastic deformation rates, and the flatness achieved after straightening at a low plastic deformation rate is relatively better than that obtained using moderate and high deformation rates. Both perpendicular to and along the straightening direction, the residual stress after straightening is less than that observed before straightening. Furthermore, the residual stress after straightening at a low plastic deformation rate is the lowest and uniformly distributed.

26 August 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
SYShengnan Yuan
Shengnan Yuan
Hui WuHui Wu
Hui Wu
HXHaibo Xie
Haibo Xie
FJFanghui Jia
Fanghui Jia
XLXiaojun Liang
Xiaojun Liang
Zhengyi JiangZhengyi Jiang
Zhengyi Jiang
In this study, the abrasive impact wear behaviour of a bimetal composite made of medium manganese steels (MMSs) and low carbon steels (LCSs), i.e., the Mn8/SS400 bimetal composite, was investigated using a newly designed wear-testing rig. The need for a new rig arose from the difficulty in replicating real-world wear conditions. Our rig allows for precise control and measurement of wear, simulating harsh environments more accurately than other wear-testing rigs. The bimetal composite Mn8/SS400 demonstrated superior wear resistance, showing an improvement of up to 2.8 times compared to benchmark steels, attributed to its enhanced work hardening sensitivity. Scanning electron microscopy (SEM), X-ray diffractometer (XRD), and electron backscatter diffraction (EBSD) analyses were employed to elucidate the wear mechanisms. After 300 h of abrasive impact wear, the subsurface microhardness of Mn8 reached 601.31 HV, significantly higher than that of the matrix hardness of 292.24 HV, indicating a substantial work hardening effect. The wear mechanism of the Mn8/SS400 bimetal composite was found to be a synergistic effect of grain refinement strengthening, dislocation strengthening, and twin strengthening. Initially, twin strengthening was the dominant mechanism up to 200 h of wear testing. However, after 300 h, contributions from all three mechanisms became increasingly significant, enhancing the overall wear resistance of the composite.

8 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
SYShengnan Yuan
Shengnan Yuan
CZCunlong Zhou
Cunlong Zhou
HXHaibo Xie
Haibo Xie
MRMengyuan Ren
Mengyuan Ren
Fei LinFei Lin
Fei Lin
Zhengyi JiangZhengyi Jiang
Zhengyi Jiang
This study examines the deformation behaviour and fracture mechanisms of bimetal composites (BCs) composed of high-carbon medium-manganese steel (Mn8) and low-carbon steel (SS400), fabricated through hot roll bonding. The research highlights the effect of varying thickness ratios on the mechanical properties of Mn8/SS400 BCs. The microstructure and interfacial characteristics were analysed using scanning electron microscopy (SEM), revealing a well-bonded and defect-free interface with distinct elemental distributions. Tensile and bending tests were conducted to evaluate the composites’ mechanical performance, highlighting the synergistic effects of Mn8’s high strain hardening capacity and SS400’s ductility. Mathematical models, including the rule of mixtures (ROM) and the long-wavelength approach (LWA), were employed to predict the tensile strength and plastic instability strain (PIS), with experimental results showing deviations due to interfacial strengthening mechanisms and dislocation pile-ups. The findings provide insights into the interplay between layer thickness ratios, interfacial properties, and strain hardening, offering valuable guidance for optimising the design and industrial-scale production of Mn8/SS400 BCs.

2 May 2024 in Research Square
Verified
Preprint
Open access
PDF file
SYShengnan Yuan
Shengnan Yuan
HWHui Wu
Hui Wu
HXHaibo Xie
Haibo Xie
FJFanghui Jia
Fanghui Jia
XLXiaojun Liang
Xiaojun Liang
ZJZhengyi Jiang
Zhengyi Jiang
In this study, the abrasive impact wear behaviour of a bimetal composite made of MMSs and LCSs (Mn8/SS400) were investigated by comparison with the existing wear resistant steels (benchmark steels) using a newly designed wear testing rig. The parameters including wear loss, wear rate, and hardness were evaluated. Scanning electron microscopy (SEM), X-ray diffractometer (XRD), and electron backscatter diffraction (EBSD) were used to analyse the wear mechanisms. The wear resistance of Mn8/SS400 bimetal composite is up to 2.8 times higher than that of benchmark steels due to better work hardening sensitivity of the bimetal composite. After 300 h abrasive impact wear, the highest microhardness of the subsurface layer for Mn8 reaches 601.31 HV, which is much greater than that of matrix (292.24 HV), showing a remarkable work hardening effect. The wear mechanism of Mn8/SS400 bimetal composite is ascribed to synergistic effect of grain refinement strengthening, dislocation strengthening, and twin strengthening. Prior to the 200-h abrasive impact wear test, the dominant wear mechanism in the Mn8/SS400 bimetal composite is primarily attributed to twin strengthening. However, following the 300-h impact wear test, the contribution to wear resistance becomes increasingly significant from all three strengthening mechanisms (dislocation, grain refinement, and twin strengthening).