Elfira Sagymbekova

Mrs. Elfira Sagymbekova

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2025 in Open Engineering
Verified
Journal Article
Open access
PDF file
DADanagul Aubakirova
Danagul Aubakirova
ESElfira Sagymbekova
Elfira Sagymbekova
YKYernat Kozhakhmetov
Yernat Kozhakhmetov
Piotr KowalewskiPiotr Kowalewski
Piotr Kowalewski
YDYerkhat Dauletkhanov
Yerkhat Dauletkhanov
AUAzamat Urkunbay
Azamat Urkunbay
This research aims to optimizing the synthesis of Ni–Ti–Cu alloys with shape memory effect (SME) through a combination of mechanosynthesis and spark plasma sintering (SPS). It has been established that the rotation speed (650/750 rpm) and the duration of mechanosynthesis (1–8 h) critically affect the phase composition and morphology of the powders. The speed of the formation of the intermetallic phase NiTi is limited at 650 rpm, whereas it intensifies defect accumulation and amorphization at 750 rpm. X-ray phase analysis and scanning electron microscopy confirmed that the optimal mechanosynthesis regime (8 h, 750 rpm) ensures: synthesis of target phases B2-NiTi and B19 ′ -NiTi; minimal crystallite size ( ∼ 109 Å); high chemical homogeneity ( ∼ 46 at% Ni, ∼ 42 at% Ti, ∼ 10 at% Cu). Subsequent SPS at 850–900 ° C and 49.2 MPa allowed for the production of dense samples. Sintering at 90 0 ° C after mechanosynthesis at 750 rpm ensured the predominance of the stable B2 austenitic phase, high microstructural homogeneity, and minimal porosity, which is critical for the reversibility of martensitic transformations. EDS analysis confirmed the chemical homogeneity ( ∼ 46 at% Ni, ∼ 42 at% Ti, ∼ 10 at% Cu) and the uniform distribution of elements. The results demonstrate the effectiveness of combining mechanosynthesis at an increased rotation speed and reduced duration with SPS for the formation of microstructures optimized for the requirements of shape memory alloy (SMA) materials.

30 October 2025 in Crystals
Verified
Journal Article
Open access
PDF file
DADanagul Aubakirova
Danagul Aubakirova
ESElfira Sagymbekova
Elfira Sagymbekova
YKYernat Kozhakhmetov
Yernat Kozhakhmetov
YDYerkhat Dauletkhanov
Yerkhat Dauletkhanov
AUAzamat Urkunbay
Azamat Urkunbay
YTYERKEZHAN TABIYEVA
YERKEZHAN TABIYEVA
This study investigates the control of the phase-structural state in Ni–45Ti–xCu (x = 5, 7 at.%) shape memory alloys fabricated via a shortened powder metallurgy route: mechanical activation → spark plasma sintering (SPS) → heat treatment. Compact samples were produced from mechanically alloyed powders (650–750 rpm, up to 5 h) and sintered at 900 °C. The structure and microstructure were characterized using X-ray diffraction (to identify B2/B19′/Ni4Ti3 phases and assess ordering) and SEM–BSE/EDS (to analyze morphology, porosity, and Ni-rich precipitates). Two post-processing treatments were applied: single-stage annealing (500 °C, 2 h) and a three-stage treatment (900 °C/30 min → water quenching → 300 °C/20 min). Mechanical alloying transformed the initial elemental powder mixture (fcc-Ni, hcp-Ti, fcc-Cu) into a supersaturated fcc-(Ni, Cu, Ti) solid solution with emerging NiTi phases, with a minimum particle size achieved after ~300 min at 750 rpm. SPS compaction yielded a high-density matrix consisting predominantly of the B2 phase. Single-stage annealing preserved B19′ martensite and Ni4Ti3 precipitates, particularly in the 5 at.% Cu alloy. In contrast, the three-stage treatment dissolved the Ni4Ti3 precipitates, suppressed the formation of B19′ and R phases, and stabilized a highly ordered B2 matrix. Increasing the Cu content from 5 to 7 at.% significantly enhanced the B2 phase fraction, reduced secondary nickel-rich phases, and improved structural homogeneity, evidenced by a continuous neck network and closed porosity. The optimized condition—7 at.% Cu combined with the three-stage annealing—produced a microstructure with >95% B2 phase, <1% Ni4Ti3, and ~98% relative density. This forms the prerequisite microstructural state for a narrow transformation hysteresis and high functional cyclic stability.

21 January 2026 in Crystals
Verified
Journal Article
Open access
PDF file
YTYERKEZHAN TABIYEVA
YERKEZHAN TABIYEVA
DYDias Yerbolat
Dias Yerbolat
SZSayat Zakerov
Sayat Zakerov
YDYerkhat Dauletkhanov
Yerkhat Dauletkhanov
AUAzamat Urkunbay
Azamat Urkunbay
NKNurgamit Kantay
Nurgamit Kantay
This work investigates the effect of titanium content and the duration of mechanical alloying on the structural and phase state of powder mixtures in the Ni–Al–Ti system. The initial mixtures of Ni68Al25Ti7, Ni72Al22Ti6, Ni70Al21Ti9, and Ni75Al25 were subjected to high-energy milling in a planetary ball mill for 1–6 h. It was found that the addition of titanium accelerates the dissolution of components and promotes the formation of a supersaturated fcc Ni(Al,Ti) solid solution. The most pronounced effects were observed for the Ni70Al21Ti9 composition, where after 6 h of alloying, the minimum crystallite size (11.3 nm) and maximum lattice strain (1.52%) were achieved. It is shown that titanium reduces the tendency for cold welding and promotes more uniform particle refinement. The optimal conditions for synthesizing a nanocrystalline solid solution with a homogeneous structure are a titanium content of 9 at.% and a mechanical alloying duration of 6 h. The resulting powders are promising for subsequent sintering and application in structural and heat-resistant intermetallic alloys and coatings.

10 February 2025 in Crystals
Verified
Journal Article
Open access
PDF file
YKYernat Kozhakhmetov
Yernat Kozhakhmetov
YTYERKEZHAN TABIYEVA
YERKEZHAN TABIYEVA
NMNuriya Mukhamedova
Nuriya Mukhamedova
AUAzamat Urkunbay
Azamat Urkunbay
MAMadina Aidarova
Madina Aidarova
ESElfira Sagymbekova
Elfira Sagymbekova
This study is focused on the sorption properties and the changes in the structure and state of Ti-25Al-25Nb (at.%) system alloys under thermal cyclic loading. These samples were produced by combining high-energy processing methods through mechanization and spark plasma sintering in the temperature range of 1100–1300 °C, followed by two-stage heat treatment at temperatures of 800 °C and 1250 °C. Thermal cyclic experiments on hydrogen sorption/desorption with samples of the Ti-25Al-25Nb (at.%) system were conducted at the VIKA experimental installation at a saturation temperature of about 500 °C and a degassing temperature of 610 °C. It took about 41 min to reach pressure equilibrium at 500 °C. The hydrogen diffusion coefficient was calculated based on the Barrer formula and was 9.1 × 10−5 cm2/s at 500 °C. The maximum hydrogen content was recorded after the first sorption/desorption cycle and was 1.91 wt%. Due to the multiple thermal cyclic effects in the hydrogen medium, the predominantly two-phase (O + B2) alloy structure underwent transformation to form a new structure (O-AlNbTi2). In the phase composition of the Ti-25Al-25Nb (at.%) alloy, the formation of hydrides in the form of independent phases as a result of thermal cycling was not detected. Hydrogen absorption is most likely to be associated with the formation of an interstitial solution based on existing crystalline phases.

15 October 2026 in Crystals
Verified
Journal Article
Open access
PDF file
YDYerkhat Dauletkhanov
Yerkhat Dauletkhanov
DYDias Yerbolat
Dias Yerbolat
YSYerzhan Sapatayev
Yerzhan Sapatayev
LILeonid Izmaylov
Leonid Izmaylov
Piotr KowalewskiPiotr Kowalewski
Piotr Kowalewski
ASAmangeldi Sagidugumar
Amangeldi Sagidugumar
Tungsten borides are promising superhard materials, but their mechanochemical synthesis requires prolonged processing, leaving the early and intermediate stages of mechanical alloying (MA) and the role of boron content largely unexplored. This study investigated the effect of boron content and high-energy MA duration (2–10 h) on the morphology, particle size distribution, and structural and phase evolution of W–B powder mixtures, comparing a near-stoichiometric W90B10 composition with a boron-excess W80B20 composition. Scanning electron microscopy, laser diffraction, X-ray diffraction, and TEM-EDS were used for characterization. The average particle size of W90B10 initially increased to 3.48 μm after 6 h and then decreased to 1.28 μm after 10 h, whereas W80B20 exhibited non-monotonic behavior, stabilizing at approximately 4.3 μm. With increasing MA duration, bcc-tungsten reflections broadened and weakened, indicating a highly disordered nanocrystalline state. Reflections of hexagonal WB2 (crystallite size 12.5 nm) appeared in W90B10 after 8 h, whereas no crystalline boride phases were detected in W80B20 up to 10 h. TEM–EDS and SAED analyses revealed local compositional inhomogeneity and provided additional crystallographic support for the formation of nanocrystalline WB2. These results show that boron content determines the kinetics of boride phase formation and the morphology evolution pathway during MA, identifying W90B10 as the more favorable composition for rapid nanocrystalline WB2 synthesis.