Fatigue life of heavily loaded rolling bearings is strongly dependent on elastic-plastic material properties. For bearing steels these elastic-plastic properties can be accurately obtained by performing monotonic or half-compressive tests. A three-dimensional strain deformation analysis based on the incremental theory of plasticity and the use of Prandtl-Reuss relations in conjunction with the von Mises yield criterion was developed in order to evaluate the permanent deformation in dry contacts loaded above the elastic limit in case of normal loading. The Ramberg-Osgood stress-strain relation for two martensitically hardened variants of SAE 52100 bearing steel considered the nonlinear kinematic and/or isotropic material behavior. Parameters describing the influence of retained austenite are modeled by using a nonlinear isotropic law. Pressure distribution and contact surface displacements during incremental loading are evaluated by using a conjugate gradient method and the internal stress field is derived by using the superposition principle. Further, a fast analysis of smooth surfaces in elastic-plastic static and rolling contact is developed based on analytical relations for the internal stress field. Cyclic evaluation of plastic strains and residual stresses is carried out until shakedown. In order to verify the theoretical model, rolling contact tests under high normal load were performed. Residual stresses and residual profiles measurements show excellent agreement between numerical and measured cyclic values.

Classical and modern methods are used to release curcumin by degrading the polysaccharides found in the turmeric powder matrix. Classical methods use chemicals as acids (HCl, H₂SO₄, CH₃COOH), oxidants (H₂O₂, kojic acid), and enzymes (amylase type) that can degrade amylose and amylopectin from starch. The modern applied methods consist of the degradation of the polysaccharides in the turmeric powder during eco-friendly processes assisted by ultrasound or microwaves. The extraction medium can consist of only water, water with a solvent, and/or an oxidizing agent. The presence of curcumin in turmeric powder is confirmed by FTIR analysis. The UV–VIS analysis of the extracts allows the determination of the efficiency of modern extraction processes. The release of curcumin from turmeric is highlighted quantitatively by colorimetric measurements for the obtained extracts, using a portable DataColor spectrophotometer. The comparison of the results leads to the conclusion that microwave-assisted extractions are the most effective. These extracts are able to dye many types of textile fibers: wool, cotton, hemp, silk, polyacrylonitrile, polyamide, polyester, and cellulose acetate. CIELab and color strength (K/S) measurements indicate that the most intense yellow colors are obtained on polyacrylonitrile (b* = 86.32, K/S = 15.14) and on cellulose acetate (b* = 90.40, K/S = 14.17).

This paper describes a model for the prediction of micro-plastic material transformation and associated residual stress field development in bearing steels during over-rolling. The high and mainly hydrostatic pressure field induced by the rolling element load, leads to the development of micro-plastic deformation in the subsurface layer of the rolling contact. The resulting plastic strain distribution gives rise to an associated self-equilibrating residual stress field that can be experimentally quantified using X-ray diffraction methods. A novel three-dimensional elastic-plastic over-rolling solution is used to evaluate the plastic strains and material transformation. Central to this plastic contact formulation is the incremental approach to deal with nonlinear material behavior. The Prandtl-Reuss constitutive equations in conjunction with Huber-Mises-Hencky yield criterion and Ramberg-Osgood strain-hardening relationships are applied to describe the plastic behavior of common hardened bearing steels. A nonlinear isotropic law is applied to describe the transformation of the retained austenite during stress cycles and changes in the strain-hardening behavior of the material microstructure. Application of this model with an incremental solution scheme based on the Conjugate Gradient Method (CGM) gives good convergence properties and fast solution for each cycle. Comparison between experimentally obtained residual stresses and stress fields derived from the present micro-plastic contact model, indicates good agreement. Numerical simulations, carried out to derive the maximum operating contact pressures in the elastic regime are also in agreement with published data. The model opens new possibilities in the evaluation of steels and heat treatments used in rolling bearings. Furthermore, this micro-plastic contact model may help the interpretation of the load history leading to a given pattern of residual stress measured in bearing rings.

This article demonstrates that the quality of laundry soap obtained by hot/cold saponification of two vegetable oils (olive and coconut) and an essential oil (such as Neem, Tea Tree or Thyme) influences the effects obtained after washing textiles: cleansing capacity and antibacterial effect. The results of FTIR, SEM, EDX, thermogravimetry and colorimetry analyses are presented comparatively for hot- and cold-prepared soaps. Saponification, Iodine number and Iodine Number Saponification values are determined for each oil but also for the mixture used in soap-making. Soap quality refers to texture, hardness, foaming capacity, stability, durability, cleansing capacity after washing and antimicrobial capacity. The removal power of greasy dirt (heavy used engine oil) of these laundry soaps is higher than that of some commercial soaps, obtaining dirt visibility <2.6% after washing at 100 °C, soiling addition density SAD < 0.0229 and cleansing capacity between 80.88 and 92.16%. UV-VIS analysis confirms the presence of essential oil in soaps (even after 10 months from manufacture) but also in textiles washed with them. The essential oil imparts strong antimicrobial properties to the laundry soaps (since they do not allow for attachment or multiplication of microorganisms from the environment), which makes them particularly useful in washing and disinfecting textile products used in hospitals.