An electric oil pump (EOP) for the hydraulic system of a continuously variable transmission (CVT)-based hybrid electric vehicle is developed, by considering the arrangement of structures and the realization of electric drive mode (EDM). The basic parameters required for the EOP motor are obtained by analyzing the flow rate and pressure of CVT. Then, the EOP motor is designed and developed. Current-pressure characteristics of different solenoid valves are measured and analyzed for designing the CVT speed ratio controller. The speed ratio controller, pressure controller, and EOP control strategy are analyzed in detail with the use of EOP as the power source of the hydraulic system only. The performances of the speed ratio controller and the EOP control strategy are verified on a test bench. Experimental results show that the steady-state error of the speed ratio controller is minimal, and the response time of speed ratio from 0.7 to 1.4 can be shortened approximately 0.49 s to 1.40 s by increasing the EOP speed from 1000 rpm to 2500 rpm. The actual EOP speed can also be adjusted by the demand of system flow to save the maximum amount of energy.
In order to develop continuously variable transmission (CVT) suited for electric vehicle (EV), a comparative analysis of the transmission used on EV is introduced in this paper. To solve the problems of traditional CVT used for EV, a newly designed electric CVT (ECVT) is proposed. The final drive ratio, speed ratio range of variator and hydraulic system of ECVT are redesigned for improving the transmission efficiency. Considering that the permanent magnet synchronization traction motor (PMSTM) of EV has an ideal driving characteristic (Constant torque at low speed, constant power at high speed) and wider high efficiency area compared with gasoline engine, the speed ratio control strategy of ECVT is studied again for improving the vehicle driving range and better meeting the requirements of driver. Finally, a simulation test system is fabricated for evaluating the battery energy consumption of an EV equipped with ECVT and single-speed transmission (SST) under constant speed and road drive cycle. The simulation results show that the ECVT proposed can extend the endurance mileage of EV at the speed of 20 to 90km/h, and improve the acceleration performance from 0 to 50km/h. The EV equipped with ECVT showed more advantages compared with SST in urban conditions.
A new dual-motor plug-in hybrid system has been developed in this paper. The system has a variety of operating modes such as "pure electric drive", "series hybrid drive", "parallel hybrid drive", and "pure oil drive", which can maximize fuel efficiency according to the driving conditions of the vehicle and the needs of the driver. By adding high-power on-board chargers and high-capacity lithium-ion battery packs to the system, more electric driving can be achieved. This paper introduces the parameters and performance indexes of the main components of the system, establishes the simulation model of the powertrain, formulates the control strategy, and analyzes the power performance and fuel economy of the system through simulation. The simulation results are as follows: the maximum speed of the vehicle can reach 180.82km/h; the acceleration time of 100 km/h is 7.72s; in the WLTC driving cycle, the fuel consumption of the hybrid power system is 7.648L/100km; the electric driving range is 156.63 km. The simulation results show that the powertrain can reduce fuel consumption while maintaining sufficient power performance, which proves the feasibility and fuel economy potential of the scheme.
An electric oil pump (EOP) must be used to supply oil for actuators in the hybrid continuously variable transmission (CVT) on the launch state of vehicle. To develop this EOP, the current CVT‐based hybrid schemes and the use of EOP on traditional automatic transmissions are analysed. Permanent magnet synchronous motor (PMSM) type is chosen as the power source of the developed EOP for its advantages of high efficiency and long‐life cycle. The PMSM EOP motor is designed and simulated by ANSYS EM. Based on the parameters of the simulation results, the sensor‐less speed controller of the EOP is designed. Then, the model of the EOP and its load CVT hydraulic system are established by Simulink and AMEsim, respectively, for joint simulation. The simulation results show that the EOP can respond to the speed command request quickly, and when the load of the hydraulic system changes it also can keep the speed stable. Finally, based on the developed prototype of EOP and hybrid CVT, the correctness of the developed EOP and its sensorless speed controller are verified by bench test.
1 January 2018 in Journal of Mechanical Engineering