This paper presents for the first time a fully integrated galvanic isolation interface in a GaN technology. It is based on planar micro-antennas and chip-to-chip communication with an on-off keying-modulated RF carrier. This approach can achieve high isolation rating and high common-mode transient immunity by properly setting the distance between chips. The interface provides the isolation channel for a main driver/power switch and the one for the control feedback of the dc-dc converter providing the isolated power supply. Driver and power control channels adopt an RF carrier of 2 GHz and 1.2 GHz, which are modulated by a pulse width modulated signal of 2 MHz and 0.5 MHz, respectively. The interface includes a continuously operating offset compensation approach, which overcomes not only the strong variations due to the large process tolerances of the GaN technology, but also offset drifts due to temperature variations. An accurate pulse width modulated signal with a large duty cycle variation in both channels was achieved. The isolation interface adopts a 6-V power supply, which delivers a quiescent current of 6.3 mA and 7.5 mA to the driver and power control channels, respectively, assuming a signal with a duty cycle of 50%.
The first fully integrated GaN pulse width modulation (PWM) generator for power conversion applications is presented in this paper. The solution is implemented in a 0.5-μm technology, avoiding additional pins and external capacitors for sawtooth signal generation while providing high accuracy. Indeed, the large GaN process spreads are addressed through an innovative dynamic offset compensation approach whose clock signal takes advantage of the PWM signal itself. The proposed PWM generator adopts a 6-V power supply and includes a 25 digital divider to set the PWM frequency at 500 kHz and the minimum and maximum duty cycles at 6% and 94%, respectively. Experimental results on integrated prototypes validated the correct circuit functionality over the temperature range from -40°C to 120°C. As a main achievement, this work demonstrates effective all-GaN integration of complex mixed analog and digital circuits, thus representing a significant advancement in the approaches to overcome the main limitations of GaN devices and enable fully integrated signal processing implementation.
6 March 2025 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents the design and experimental measurement of a fully integrated gate driver fabricated together with a 200-V GaN power switch in a GaN-on-SOI technology. The driver exploits 20-V low-voltage enhancement-mode HEMTs (E-HEMTs), Metal-Insulator-Metal (MIM) bootstrap capacitors and two-dimensional electron gas (2DEG) resistors. To overcome the inherent lack of p-channel devices in the GaN technology, the design employs the bootstrapping approach which allows for full turn-on of the 200-V power GaN switch while minimizing static power consumption. Furthermore, the relatively high breakdown voltage (20 V) of the low-power E-HEMTs allows them to withstand the high voltages generated during bootstrapping. Static power consumption is further reduced by minimizing the number of ratioed logic inverters and implementing an anti-cross-conduction network to eliminate cross-conduction switching losses. The design also leverages the third quadrant of the HEMTs’ IDS-VDS characteristic to emulate the diode behavior, potentially reducing external component requirements. Measured performance reveals an average gate driver current consumption ranging from 370 μA at -40 ∘C to 150 μA at 150 ∘C. Additionally, the rise and fall times when driving the power switch with 365-mΩ on-resistance are respectively 6.5 ns and 3.5 ns at room temperature.
26 November 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
Modern high-performance electronics is pushing Si technology to its limits. Gallium Nitride (GaN) emerges as a promising alternative due to its superior properties in high-frequency and high-power applications. To fully utilize the fast-switching ability of the GaN technology, monolithic integration is a key. A monolithically integrated GaN power IC (Integrated Circuit) reduces the inductive parasitic enabling a fast efficient switching operation. However, GaN basic building blocks, particularly operational amplifiers (Op-Amps), face severe challenges due to the limitations of the GaN technology. This paper presents the first three-stage Op-Amp for high-performance feedback circuits realized in the IMEC’s 200-V GaN-IC technology on a GaN-on-SOI (Silicon on Insulator) substrate. The design utilizes a cascade of three differential stages resistively loaded to achieve a nearly 60-dB DC gain and 25-MHz gain-bandwidth and implements a novel dual single-Miller frequency compensation technique to provide closed-loop stability. The Op-Amp offers a Slew Rate exceeding 70 V/μs with 1% settling time of about 120 ns at room temperature. The correct circuit functionality from −40 °C to 150 °C was demonstrated through simulations and experimental test.
This paper presents, analyzes, and experimentally validates a bootstrapped inverter implemented via low-voltage enhancement-mode HEMTs offered by a 200-V E-mode GaN-on-SOI monolithic platform. Unlike conventional resistor–transistor logic (RTL), the proposed topology exploits intrinsic device capacitances to achieve a transient current-source-like pull-up behavior without dedicated bootstrap capacitors. A detailed analytical model is developed to describe the dynamic operation and to identify the conditions under which the low-to-high transition overcomes the RC limitation of RTL inverters. Measurements demonstrate a more than 30% reduction in rise time, higher static gain, and an overall improvement in total noise margins under comparable static current conditions. The temperature dependence of bootstrap efficiency from −40 °C to 150 °C is also investigated. By combining experimental measurements with model-based parameter extraction, we show that the high-temperature performance crossover is attributed primarily to leakage-induced overdrive reduction. In contrast, threshold-voltage drift acts in the opposite direction and mobility degradation affects both topologies similarly.
This paper presents a three-channel galvanic isolation interface in GaN technology. Driver, diagnostic, and control channels have been implemented in a two-die integrated system to perform an isolation interface for a high-performance power switching system. Chip-to-chip communication has been used, which is based on planar micro-antennas with on–off keying modulated RF carriers. This approach provides a high isolation rating by properly setting the distance between chips. Various innovation aspects are adopted with respect to previously published works. They mainly involve the receiver robustness thanks to the switched-capacitor bias control, a bidirectional data channel implementation for power section diagnostic, and a duty cycle distortion compensation for accurate PWM signal. Driver and control channels use RF carriers of about 2 GHz and 0.9 GHz and achieve 2 MHz and 0.5 MHz measured pulse width modulation signals, respectively. The bidirectional channel adopts an RF carrier of about 400 MHz and exhibits a maximum measured data rate as high as 10 Mb/s. Thanks to the extensive use of switched-capacitor circuit solutions, well-controlled behavior is achieved against the large process tolerances and temperature drifts of the GaN technology. The isolation interface is supplied at 6 V and occupies a die area of 7.6 mm2 for each chip.