Alessandro Castorina

Dr. Alessandro Castorina

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2023 in IEEE Access
Verified
Journal Article
Open access
KSKatia Samperi
Katia Samperi
NSNunzio Spina
Nunzio Spina
ACAlessandro Castorina
Alessandro Castorina
APAntoine Pavlin
Antoine Pavlin
Salvatore PennisiSalvatore Pennisi
Salvatore Pennisi
GPGiuseppe Palmisano
Giuseppe Palmisano
The first fully integrated GaN pulse width modulation (PWM) generator for power conversion applications is presented in this paper. The solution is implemented in a 0.5-μm technology, avoiding additional pins and external capacitors for sawtooth signal generation while providing high accuracy. Indeed, the large GaN process spreads are addressed through an innovative dynamic offset compensation approach whose clock signal takes advantage of the PWM signal itself. The proposed PWM generator adopts a 6-V power supply and includes a 25 digital divider to set the PWM frequency at 500 kHz and the minimum and maximum duty cycles at 6% and 94%, respectively. Experimental results on integrated prototypes validated the correct circuit functionality over the temperature range from -40°C to 120°C. As a main achievement, this work demonstrates effective all-GaN integration of complex mixed analog and digital circuits, thus representing a significant advancement in the approaches to overcome the main limitations of GaN devices and enable fully integrated signal processing implementation.

9 April 2024 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Open access
NSNunzio Spina
Nunzio Spina
MRMarcello Raimondi
Marcello Raimondi
ACAlessandro Castorina
Alessandro Castorina
Egidio RagoneseEgidio Ragonese
Egidio Ragonese
GPGiuseppe Palmisano
Giuseppe Palmisano
This article presents the design of a three-channel package-scale galvanic isolation interface for SiC and GaN power switching converters. The isolation interface consists of two side-by-side co-packaged chips fabricated in a low-cost 0.32- $\mu$ m bipolar CMOS–DMOS (BCD) technology and includes three isolation data channels based on RF-coupled integrated microantennas. The isolation interface provides a channel for the gate driver control, a bidirectional channel for diagnostic, and a channel for the isolated power supply control. They use on–off keying (OOK)-modulated RF carriers of 1.5, 0.5, and 1.5 GHz, respectively. The galvanic isolation interface provides a maximum signal rate of 2 and 1.9 MHz for the driver and the power control channels, respectively, whereas the diagnostic channel guarantees half-duplex bidirectional communication up to 15 MHz. Thanks to the package-scale isolation approach, both reinforced galvanic isolation and first-rate common-mode transient immunity (CMTI) are achieved. High immunity to adjacent channel crosstalk is guaranteed by using channel frequency/physical separation. To best of the authors’ knowledge, this is the first implementation of a package-scale galvanic isolation interface with three independent communication channels, including a bidirectional channel, in silicon technology.

29 March 2023 in IEEE Transactions on Microwave Theory and Techniques
Verified
Journal Article
Open access
GPGiuseppe Papotto
Giuseppe Papotto
APAlessandro Parisi
Alessandro Parisi
AFAlessandro Finocchiaro
Alessandro Finocchiaro
CNClaudio Nocera
Claudio Nocera
ACAndrea Cavarra
Andrea Cavarra
GPGiuseppe Palmisano
Giuseppe Palmisano
This article presents a 77-GHz transmitter (TX) in a 28-nm fully depleted silicon-on-insulator CMOS technology for automotive radar applications. The circuit has been designed to simultaneously fulfill both short-/medium-range (S/MR) and long-range (LR) operations. It exploits an LO frequency doubling architecture, which allows preventing voltage-controlled oscillator (VCO) pulling effects for improved phase noise (PN) performance. The proposed TX comprises a 38-GHz VCO driving a frequency doubler and then a current-combining two-path power amplifier. The VCO takes advantage of a novel tank architecture to cope S/MR and LR requirements with an effective and silicon area-saving solution. The proposed TX also features a feedback loop that allows properly setting the power delivered to the output load. It exhibits a 5-GHz bandwidth, ranging from 76 to 81 GHz, with a PN performance as low as $-$ 93 dBc/Hz at a 1-MHz offset frequency from a 77-GHz carrier. It is also able to deliver a maximum output power as high as 17.5 dBm with a dynamic control range of around 13 dB. The overall power consumption is 351 mW.

28 May 2024 in Electronics
Verified
Journal Article
Open access
PDF file
GPGiuseppe Papotto
Giuseppe Papotto
APAlessandro Parisi
Alessandro Parisi
AFAlessandro Finocchiaro
Alessandro Finocchiaro
CNClaudio Nocera
Claudio Nocera
ACAndrea Cavarra
Andrea Cavarra
GPGiuseppe Palmisano
Giuseppe Palmisano
This paper presents recent results on CMOS integrated circuits for automotive radar sensor applications in the 77 GHz frequency band. It is well demonstrated that nano-scale CMOS technologies are the best solution for the implementation of low-cost and high-performance mm-wave radar sensors since they provide high integration level besides supporting high-speed digital processing. The present work is mainly focused on the RF front-end and summarizes the most stringent requirements of both short/medium- and long-range radar applications. After a brief introduction of the adopted technology, the paper addresses the critical building blocks of the receiver and transmitter chain while discussing crucial design aspects to meet the final performance. Specifically, effective circuit topologies are presented, which concern mixer, variable-gain amplifier, and filter for the receiver, as well as frequency doubler and power amplifier for the transmitter. Moreover, a voltage-controlled oscillator for a PLL efficiently covering the two radar bands is described. Finally, the circuit description is accompanied by experimental results of an integrated implementation in a 28 nm fully depleted silicon-on-insulator CMOS technology.

29 August 2023 in Electronics
Verified
Journal Article
Open access
PDF file
APAlessandro Parisi
Alessandro Parisi
GPGiuseppe Papotto
Giuseppe Papotto
CNClaudio Nocera
Claudio Nocera
ACAlessandro Castorina
Alessandro Castorina
GPGiuseppe Palmisano
Giuseppe Palmisano
This paper presents a Ka-band three-stage power amplifier for 5G communications, which has been implemented in a 150 nm GaN-on-SiC technology and adopts a Doherty architecture. The amplifier is made up of a 50 Ω input buffer, which drives a power splitter, thanks to which it delivers its output power to the two power amplifier units of the Doherty topology, namely the main and auxiliary amplifier. Finally, the outputs of the two power amplifiers are properly arranged in a current combining scheme that enables the typical load modulation of the Doherty architecture, alongside allowing power combining at the final output. The proposed amplifier achieves a small signal gain of around 30 dB at 27 GHz, while providing a saturated output power of 32 dBm, with a power-added efficiency (PAE) as high as 26% and 18% at peak and 6 dB output power back-off, respectively.

13 November 2025 in Electronics
Verified
Journal Article
Open access
PDF file
AMAlessandro Domenico Minnella
Alessandro Domenico Minnella
GPGiuseppe Papotto
Giuseppe Papotto
AFAlessandro Finocchiaro
Alessandro Finocchiaro
APAlessandro Parisi
Alessandro Parisi
ACAlessandro Castorina
Alessandro Castorina
GPGiuseppe Palmisano
Giuseppe Palmisano
This paper presents a 0–360° phase shifter in 28 nm FD-SOI CMOS technology, suitable for radar applications and mm-wave wireless communication systems, which adopt high-efficiency transmitter architectures. It exploits a novel switching vector modulator based on a double-balanced Gilbert cell, which guarantees high-resolution phase control while exhibiting inherently high robustness against process and temperature variations. The phase control is performed by merely changing the currents in the Gilbert cells using digitally controlled current generators. The proposed phase shifter operates at 39 GHz and provides RMS phase and gain errors of 2.7–4.7° and 0.3–0.5 dB, respectively, while drawing 13 mA from a 1 V supply voltage.