This work concerns the experimental verification of changes in the energy efficiency of photovoltaic installations through the use of bifacial modules. For this purpose, an experimental stand was designed and built for the comparative analysis of the efficiency of two types of photovoltaic panels: bifacial (bPV) and monofacial (mPV). The tests consisted of placing the panels at different heights above the ground surface and at different angles. During the tests, three substrates with different albedo were taken into account: green grass, gray concrete (fabric), and white snow (polystyrene). The tests for both types of panels were carried out simultaneously (in parallel), which guaranteed the same environmental conditions (temperature and solar radiation intensity). Based on the results of the voltage and current measurements for different angles of PV module inclination and, for bPV panels, different heights above the ground surface and different types of substrate, a series of current–voltage characteristics and power characteristics were plotted. The “additional” energy efficiency of bifacial panels compared to monofacial panels was also determined. It was shown that under favorable conditions, using bifacial panels instead of monofacial panels can increase the production of electricity by more than 56% from structures of the same dimensions. The research results can be of great value when designing photovoltaic installations.
The paper describes the influence of the drum system construction of two modern carding machines on the porous structure of spunlace non-wovens composed of polyester and viscose. The non-woven fabric structure, including the number and size of the pores, determines the tensile strength of the composites obtained. The spunlace non-wovens were subjected to tensile strength tests in the machine, and cross-directions and microscopic observations of their structure were made. The results of the experiments were used to determine the relationship between the strength of the material and the porosity of its structure. This knowledge was used to prepare recommendations for the manufacturer of wet wipes in order to enable the selection of a carding machine for the mass production of final products with strength properties that meet market requirements and satisfy the end customer.
1 December 2024 in Advances in Science and Technology Research Journal
The article presents the results of experimental studies on selected, mechanical properties of three-layer film, produced by blown film extrusion. Three-layer film was developed for making garbage bags. The research was carried out under industrial conditions. The three-layer film sleeves tested...
The paper describes the influence of the drum system construction of two modern carding machines on the porous structure of spunlace non-wovens composed of polyester and viscose. The non-woven fabric structure, including the number and size of the pores, determines the tensile strength of the composites obtained. The spunlace non-wovens were subjected to tensile strength tests in the machine, and cross directions and microscopic observations of their structure were made. The results of the experiments were used to determine the relationship between the strength of the material and the porosity of its structure. This knowledge was used to prepare recommendations for the manufacturer of wet wipes in order to enable the selection of a carding machine for the mass production of final products with strength properties that meet market requirements and satisfy the end customer.
The main focus of this article is the simulation and analysis of the operating principles of selected maximum power point tracking (MPPT) algorithms for photovoltaic panels, as well as a comparison of various techniques used to address this challenge. The article discusses the underlying rationale for the necessity of identifying the operating point at which a photovoltaic panel delivers maximum power. In addition to the theoretical description, the algorithms were classified, and in the simulation section, the most popular and widely used MPPT algorithms were implemented and compared in the MATLAB 24.11 (R2024a) environment. The application of appropriate solutions among the modelled and tested algorithms enables improved efficiency of photovoltaic cells within panels or larger photovoltaic systems.
This paper presents the results of experimental tests on the static tensile strength and relative elongation of three-layer films containing varying proportions of recycled polyethylene and subjected to an embossing process. Films containing varying proportions of recycled low-density and high-density polyethylene were produced by blown film extrusion. The embossing process was carried out under varying processing conditions, and embossing patterns with different geometrical characteristics were produced on the three-layer films under investigation. The films were manufactured and the experimental tests were conducted under industrial conditions. Based on the results obtained, the effects of three different embossing pattern geometries and the embossing process parameters on the tensile strength of three-layer films made from recycled polyethylene were evaluated in the machine and transverse directions. The experimental results enabled the identification of embossing pattern geometries and recycled polyethylene contents that increased static tensile strength in selected material–process combinations. No statistically significant improvement in elongation at break was confirmed compared with the non-embossed reference films. The findings are limited to static tensile strength and elongation at break in the machine direction (MD) and cross direction (CD), which contribute to improving certain functional properties of refuse bags, specifically ensuring adequate load-bearing capacity for the waste they contain.