It is uncertain whether the interchangeable use of two adhesive systems would yield comparable shear bond strength (SBS) for both Polyetheretherketone (PEEK) and Polyetherketoneketone (PEKK); investigating this was the main objective of this study. Milled PEEK (Bredent, Senden, Germany) and PEKK (Pekkton Ivory, AnaxDent, Stuttgart, Germany) blocks were prepared with standardized roughness (0.20 μm) and randomly assigned into two groups (n = 72): with and without aluminum oxide air abrasion (AquaCare Twin, Medivance Instruments, London, UK). Two adhesive systems (Visio.link, Bredent, Senden, Germany, or PEKKBond, AnaxDent, Stuttgart, Germany) were randomly applied (n = 36). Flowable gingival composite (AnaxGum Gingiva, AnaxDent, Stuttgart, Germany) was bonded, and the samples were stored in water (37 °C, 24 h). SBS was measured (MPa) and data were analyzed using three-way ANOVA, followed by Tukey’s test (α = 0.05). All main effects and interactions were significant (p < 0.05), except for polymer (p = 0.163) and the triple interaction (p = 0.601). In the PEEK group, Visiolink showed higher SBS (p < 0.001), regardless of prior air abrasion. For the PEKK group, PEKKBond significantly increased SBS values (p < 0.001) for both pre-treatment groups. Previous air abrasion only significantly increased the SBS of controls without adhesive. This study highlights the importance of material-specific adhesive selection, rather than interchangeable use, for optimal results. The bond strength of PEEK and PEKK is influenced by the adhesive system applied. Moreover, PEKK consistently demonstrated higher SBS values in comparison to PEEK, even without the need for pre-treatment or adhesive conditioning. This characteristic renders PEKK a preferred choice for the fabrication of adhesive restorations.

Indirect laminate veneers can deliver excellent esthetic results, but their use must remain secondary to biological and functional principles, requiring an ethical and evidence-based approach during treatment planning.

Facial and dental analysis should be integrated with all dental treatments, where aesthetics and function should be the main objectives, since the face is the main basis of aesthetic balance, and dentistry must be in sync with it. The objective of this work is a literature review to identify the factors that should be considered in an aesthetic analysis of the patient when submitted to a dental treatment. The perception of a balanced face is possible, there being a diversified concept of facial beauty, and this varies according to the patient, the aesthetic treatment must always be an allied function, so that you can improve the facial harmony with the smile, return the positive aesthetic means meeting expectations and giving a positive self-image. It is concluded that the perception of a balanced face is possible, there is a diversified concept of facial beauty, and this varies according to the patient.

Objective: The aim of this study was to evaluate the pterygoid canal (PC) by Cone Beam Computed Tomography (CBCT), establishing its configuration and proximity with anatomical structures. Material and Methods: We evaluated 398 CBCT exams, all from a public University radiology clinic archive. Four parameters were evaluated: single or double PC, distance between PC and the inferior part of the sphenoid sinus (SS), ratio of PC and SS and the distance between the PC and the foramen rotundum. Results: It was observed that most of the PC of the sample presented simple morphology, the most frequent type of relationship between the PC and the SS on both sides was the close contact with the wall. Among the cases that there were some distances between the PC and the inferior wall of the SS, the mean of this distance did not exceed 3.20 mm, being the left side (3.03 mm) slightly closer than the right (3.20 mm). Finally, the distances between the PC and the corresponding Foramen Rotundum are presented with mean values of 5.87 mm for the right side and 6.31 mm for the left side. Conclusion: CBCT examination is of paramount importance for PC identification; once in the studied sample, the mean values found evidence the close relation between the PC and the SS. Keywords Cone beam computed tomography; Endonasal approach; Vidian canal.

This study evaluated the survival probabilities of two lithia-based glass-ceramics after final crystallization in a microwave furnace using conventional crystallization as a reference. Disc-shaped samples of a lithium silicate (LS, Celtra Duo) and a lithium disilicate (LD, e.max CAD) were prepared and divided into two groups according to the crystallization method (n = 30): microwave (M) or conventional furnaces (C). The biaxial flexural strength test was used to determine the fatigue test profile and its parameters. Then, specimens were submitted to an accelerated life test (step stress) using three profile levels – mild, moderate, and aggressive – varying the load increments and the number of cycles until fracture (4 Hz). Survival data were used to calculate Weibull’s beta (β) value and reliability of the assigned missions. Scanning electron microscopy was employed to analyze surface morphology, fracture characteristics, and failure patterns. Beta (β) values for the LS-C, LS-M, LD-C, and LD-M groups were 2.65, 0.25, 0.62, and 0.3, respectively. Similar reliability was observed in all groups after 50,000 cycles at 100 and 150 Mpa. At 200 Mpa, the crystallization method did not affect the reliability within LS or LD. However, LD showed greater reliability than LS when crystallized by microwave energy. Thus, microwave energy can be suggested as an alternative to the process of conventional lithia-based glass-ceramics crystallization without damaging their survival probabilities.

Introduction: In cases where there is an association of two or more diseases, it’s complex to improve individual’s well-being and quality of life, especially when these diseases have a bidirectional relation, as observed between diabetes mellitus and periodontal disease. Aim: The present study aims to review the literature on the relation between Diabetes Mellitus and Periodontal Disease, identifying the main aspects and pathognomonic characteristics.Conclusion:Due to the exposed in the literature on the interrelation of diabetes mellitus and periodontal disease, further studies are needed for a better understanding of the subject, knowing that the interdisciplinary approach is very important for the patient to have a better quality of life.