Jozef Bronček

Dr. Jozef Bronček


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2022 in Production Engineering Archives
Verified
Journal Article
Open access
PDF file
Norbert RadekNorbert Radek
Norbert Radek
AKArtur Kalinowski
Artur Kalinowski
JPJacek Pietraszek
Jacek Pietraszek
LOLukasz Orman
Lukasz Orman
MSMarcin Szczepaniak
Marcin Szczepaniak
OPOlga Paraska
Olga Paraska
A number of modern surface processing methods use an energy flux. The examples include electro-spark deposition (ESD) and laser beam processing (LBP). The work concerns the study of Cu-Mo coatings deposited on C45 carbon steel, which were then eroded with a laser beam. The analysis included the analysis of the microstructure, measurements of macrogeometry and microhardness, corrosion resistance tests of selected areas after laser treatment. The coatings were applied with ELFA-541 and subjected to Nd:YAG laser treatment with variable laser parameters. The problem presented in the work can be used to extend the knowledge of the areas of application of ESD coatings, especially in sliding friction pairs.

6 December 2018 in Metals
Verified
Journal Article
Open access
PDF file
MNMiroslav Neslušan
Miroslav Neslušan
LTLibor Trško
Libor Trško
PMPeter Minárik
Peter Minárik
JČJiří Čapek
Jiří Čapek
JBJozef Bronček
Jozef Bronček
JMJán Moravec
Ján Moravec
This paper reports about the non-destructive evaluation of surfaces after severe shot peening via the Barkhausen noise technique. Residuals stresses and the corresponding Almen intensity, as well as microstructure alterations, are correlated with the Barkhausen noise signal and its extracted features. It was found that residual stresses as well as the Barkhausen noise exhibit a valuable anisotropy. For this reason, the relationship between the Barkhausen noise and stress state is more complicated. On the other hand, the near-the-surface layer exhibits a remarkable deformation induced softening, expressed in terms of the microhardness and the corresponding crystalline size. Such an effect explains the progressive increase of the Barkhausen noise emission along with the shot-peening time. Therefore, the Barkhausen noise can be considered as a promising technique capable of distinguishing between the variable regimes of severe shoot peening.

1 December 2023 in System Safety: Human - Technical Facility - Environment
Verified
Journal Article
Open access
PDF file
AKArtur Kalinowski
Artur Kalinowski
Norbert RadekNorbert Radek
Norbert Radek
LOLukasz Orman
Lukasz Orman
JPJacek Pietraszek
Jacek Pietraszek
MSMarcin Szczepaniak
Marcin Szczepaniak
JBJozef Bronček
Jozef Bronček
Laser surface texturing (LST) has emerged as a versatile and efficient technique for modifying surface properties across various materials. This paper provides an analysis of the characteristics and diverse applications of laser surface texturing. The paper begins by explaining the fundamental principles underlying LST, highlighting the mechanisms involved in material interaction and the resultant surface modifications. It explores the influence of laser parameters such as pulse duration, energy density, and wavelength on the texturing process, emphasizes their impact on surface morphology, roughness, and topographical features. Furthermore, this paper delves into the wideranging applications of LST across different industries and fields. It examines how LST enhances surface functionalities, including improvements in tribological properties, wettability, friction reduction, and biocompatibility. Additionally, the utilization of LST for creating microstructures enabling advanced functionalities in optics, electronics, biomedical devices, and energy harvesting systems is discussed. Moreover, the challenges and future directions in LST technology are highlighted, which encompass advances in precision, scalability, and integration of LST with other manufacturing processes. The potential environmental implications and economic feasibility of LST are also discussed. In summary, this paper examines the characteristics, applications, challenges, and future prospects of laser surface texturing, showcasing its significance as a promising technology for tailoring surface properties across diverse materials and industries.

1 June 2016 in Acta Mechanica et Automatica
Verified
Journal Article
Open access
PDF file
PJPeter Jankejech
Peter Jankejech
PFPeter Fabian
Peter Fabian
JBJozef Bronček
Jozef Bronček
YSYuriy Shalapko
Yuriy Shalapko
The article describes basic principles of induction bending and the change of mechanical properties from as received (straight) pipe made from HSLA steel to induction bend. The main purpose of this article is to experiment with tempering temperatures below 540°C. After tempering at 540°C which is the lowest recommended temperature for post bend heat treatment (PBHT) according to CSA specifications (Canadian Standards Association) the induction bend area in many cases does not achieve the minimum required mechanical properties and therefore it is not accepted for usage. In this article mechanical properties such as tensile, toughness, hardness are evaluated. Also the article contains microstructural analyses and comparison of bended and heat treated samples.

1 September 2021 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
DVDaniel Varecha
Daniel Varecha
JBJozef Bronček
Jozef Bronček
RKRobert Robert Kohar
Robert Robert Kohar
FNFrantišek Nový
František Nový
MVMartin Vicen
Martin Vicen
NRNorbert Radek
Norbert Radek

1 January 2024 in Applied Engineering Letters : Journal of Engineering and Applied Sciences
Verified
Journal Article
Closed access
MVMartin Vicen
Martin Vicen
OBOtakar Bokůvka
Otakar Bokůvka
LTLibor Trško
Libor Trško
RJRichard Joch
Richard Joch
JBJozef Bronček
Jozef Bronček
Robert UlewiczRobert Ulewicz
Robert Ulewicz
The roughness and lubrication of the contact surfaces play a major role in determining the contact forces and the coefficient of friction during contact between the two parts. The objective of the research, the results of which are presented in this paper, was to establish what, in fact, is the influence of those two important parameters on the surface properties of the shot- peened C35 steel specimens. Another important aspect that was considered was the influence of the post-treatment of the shot-peened specimen surfaces, the fine grinding. The experimental work included verification of the steel’s chemical composition (as compared to the standard values), the heat treatment, evaluation of the material’s microstructure, measurement of the mechanical properties, the shot-peening treatment and evaluation of the magnitude of the compressive residual stresses, measurement of the surface roughness profiles and the friction tests. An effect of the surface roughness and lubricant on the coefficient of friction (CoF) was established. The CoF values of the dry shot-peened steel surface after the fine grinding, as compared to the unground surface, decreased from about 30% to 39%. The application of lubricant caused the CoF to decrease by 66% and 43% for the ground and unground surfaces, respectively.