Chengtao Wang

Dr. Chengtao Wang


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2013 in Prosthetics and Orthotics International
Verified
Journal Article
Open access
HZHai Zhou
Hai Zhou
ALAnmin Liu
Anmin Liu
DWDongmei Wang
Dongmei Wang
XZXiangsen Zeng
Xiangsen Zeng
SWSan Wei
San Wei
CWChengtao Wang
Chengtao Wang
Sitting cross-legged as an activity of daily living and its kinematics have significantly different demands on the arthroplasty of hip and knee, which can be referred in the design of joint arthroplasty. The purpose of this study was to obtain the kinematics of the lower limb in Chinese people during cross-legged sitting. This study identified the necessary requirements for joint arthroplasty to carry out sitting cross-legged activity. A total of 40 healthy Chinese participants (average age = 23.8 years) performed six cross-legged sitting trials per person. Three-dimensional kinematic data of ankle, knee, and hip joints were collected; the means of the three-dimensional angles of these three joints were calculated. At the hip, the range of motion of the flexion was 101.7°, the abduction reached 43.2°, and the range of motion of the external rotation was 36.4°. At the knee, the range of motion of the flexion was 131.9° and the range of motion of the internal rotation reached 32.4°. At the ankle, the range of motion in three planes was not great. Such motion ranges were likely to result in prosthetic dislocation. The results would provide valuable references for prosthesis design in the Chinese population. The kinematic data of sitting cross-legged activity provided the baseline information for physicians and therapists concerned with the surgical and functional rehabilitation, and offered reference for lower limbs prosthesis designing.

4 March 2019 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
CWChengtao Wang
Chengtao Wang
DCDa Cheng
Da Cheng
KZKai Zhang
Kai Zhang
YWYingzhe Wang
Yingzhe Wang
EKErshuai Kong
Ershuai Kong
QXQingjin Xu
Qingjin Xu
R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics (IHEP) for pre-study of high energy accelerators in the future. As the first step, a 12-T subscale common-coil dipole magnet named LPF1 (Let the Proton Fly) with two 7 mm apertures and graded coil configuration was designed, fabricated, and tested. With 4 NbTi double-pancake racetrack coils outside and 2 $\rm Nb_{3}Sn$ double-pancake racetrack coils inside, this hybrid dipole magnet was designed to provide a 12-T main field in two apertures operating at 6100 A. The load line ratio is 83 % @ 4.2 k for the designed current and field. To reduce the field enhancement at the ends of the coils, the coils were designed with different lengths. All of the six coils were wound with superconducting Rutherford cables and impregnated with epoxy CTD-101k. Bladders and keys technology was used to pre-stress coils during the assembly of LPF1. A 0.1 Ohm dump resistor and a voltage dependent varistor were used for the quench protection during the test of LPF1. LPF1 was tested at 4.2 K under the self field and a field plateau had been shown around 10.2 T after the $\rm 13^{th}$ quench. The parameters of the design, the process of the fabrication and the test performance of LPF1 are presented in this paper.

5 May 2023 in Superconductor Science and Technology
Verified
Journal Article
Closed access
CWChengtao Wang
Chengtao Wang
YWYingzhe Wang
Yingzhe Wang
JSJinrui Shi
Jinrui Shi
ZFZe Feng
Ze Feng
CLChunyan Li
Chunyan Li
QXQingjin Xu
Qingjin Xu
The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb3Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb3Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb3Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb3Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid—Nb3Sn, NbTi—common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.

9 November 2018 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
KZKai Zhang
Kai Zhang
YWYingzhe Wang
Yingzhe Wang
CWChengtao Wang
Chengtao Wang
DCDa Cheng
Da Cheng
EKErshuai Kong
Ershuai Kong
QXQingjin Xu
Qingjin Xu
A Nb3Sn/NbTi subscale dipole magnet named LPF1 with graded coil design and common-coil configuration has been designed, assembled and tested at IHEP, China. Compared to the previously proposed FECD1, LPF1 is designed with a longer outer NbTi racetrack coil to reduce the peak field in the coil end. The computed bore field and peak coil field of LPF1 is 12.0 T and 12.1 T if it works at 6100 A with a safety margin of 17% at 4.2 K. The horizontal and vertical directions of the coil packs are preloaded by using bladder & key technology while the axial direction of the coil packs is preloaded by pre-tightening four aluminum rods. Before assembly, we tested the electron-beam welded (EBW) bladders in a subscale shell-support structure and verified the strain measurement system. During assembly, we preloaded the coil packs gradually by referring to the measured shell strain after inserting stainless steel keys and removing the bladders. After assembly, we started to test the subscale dipole magnet vertically at 4.2 K. LPF1 reached a bore field of 10.2 T after 13 training quenches and then it reached a stable quench current without detraining. This paper presents the updated design parameters, the stress analysis, the magnet assembly and test of LPF1.

16 November 2023 in Superconductor Science and Technology
Verified
Journal Article
Open access
PDF file
CLChunyan Li
Chunyan Li
JZJin Zhou
Jin Zhou
YZYanchang Zhu
Yanchang Zhu
CLCong Liu
Cong Liu
RKRui Kang
Rui Kang
QXQingjin Xu
Qingjin Xu
To explore the potential of iron-based superconducting (IBS) tapes in high-field applications, IBS pancake coils were dry-wound using the uninsulated IBS tape, supplemented with cowound stainless steel tapes for reinforcement. We have successfully fabricated a double pancake coil (DP-1) and a series-connected coil consisting of six DP coils (DP-6). These coils underwent multiple charging tests in a 35 T resistive magnet and retesting in a 14 T superconducting magnet. After conducting multiple rounds of retesting in two different background field magnets, it was found that the IBS coils did not show any degradation in their current-carrying performance. The critical current (I c) value of the DP-1 at 4.2 K and 32 T reached 60 A. To systematically evaluate the I c performance of the six coils in the DP-6, we monitored the V–I curves between 26 voltage taps. The resistive voltage rise was observed at low charging currents, indicating that each coil has suffered different levels of damage. Nevertheless, the overcurrent tests demonstrated that the IBS coil can still carry a current far exceeding its I c without irreversible degradation. We concluded the possible reasons for these phenomena by analyzing the experimental details and test data. In addition, the coil’s internal structure was observed to assess the quality of coil winding, joint soldering, and epoxy resin impregnation. This study will provide references for the electromagnetic and mechanical properties of IBS tapes under ultra-high magnetic fields and contribute to the future development of higher-performance practical IBS coils.

3 June 2022 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
HYHuanli Yao
Huanli Yao
YZYalin Zhao
Yalin Zhao
HZHua Zhang
Hua Zhang
YWYingzhe Wang
Yingzhe Wang
CWChengtao Wang
Chengtao Wang
QXQingjin Xu
Qingjin Xu
Epoxy resins are commonly used in high field superconducting magnets for electrical insulation and mechanical reinforcement. However, many of the epoxy systems for vacuum pressure impregnation (VPI) techniques show drawbacks like easy cracking at low temperatures, short pot life, and/or low glass transition temperatures ( T g ), etc . High-field dipole magnets are under development at the Institute of High Energy Physics (IHEP) for the pre-study of future high-energy accelerators. Finding the most appropriate epoxy is critically important. Herein, a new epoxy resin (named IR-3) is developed. Its potting properties including thermal shock, viscosity, T g , and mechanical strength before and after radiation are presented and were compared with CTD-101K which is mostly used in accelerator magnets. Additionally, the thermal and electrical characteristics of high-temperature superconductor (HTS) coils encapsulated with these epoxies were also investigated. The results show that IR-3 is a promising encapsulating material for impregnating HTS coils and has the potential application in high field accelerator magnets.