2 July 2019 in IEEE Transactions on Applied Superconductivity
Quench protection is a critical issue for magnet using high temperature superconducting (HTS) materials like REBCO. For cable-in-conduit conductor (CICC) with twisted REBCO tapes, which is considered for high current HTS conductor for fusion magnet, the anisotropic critical current density (Jc) of tape and complex conductor layout will further complicate the quench behavior. The CryoSoft code THEA is used to simulate the quench behavior of various sub-scale CICCs in view of a quench experiment in SULTAN facility. The CICCs are composed of the twisted tape stack assembled into copper shell (strand). It has been found that neglecting the anisotropy of Jc in quench simulation will significantly underestimate the hot spot temperature by about 40 K. Therefore, it could leave potential risk to damage the magnet. It is also shown that the thermal contact resistance between strand and the steel jacket (the conduit) plays a very important role on quench behavior. The hot spot temperature can be reduced by more than 100 K if the thermal resistance is reduced by two order of magnitude. On the other hand, variations of inter-strand electrical and/or thermal resistance have only very little influence (few Kelvin).
4 March 2021 in IEEE Transactions on Applied Superconductivity
High Temperature Superconductors (HTS) are promising materials for future fusion magnets. One of HTS conductors' main issues is the quench protection: the quench develops much slower than in LTS, delaying the quench detection by voltage monitoring and causing a massive temperature increase before detection. The Swiss Plasma Center (SPC), with the support of EUROFusion, has upgraded the SULTAN facility to test large current conductors during the whole quench evolution. The 100 kA superconducting transformer has been replaced by an 18 kA direct power supply, which allows sustaining the operating current in the sample during a quench. Five HTS conductors have been manufactured at SPC: they are sub-size of the HTS high-current cables designed by the group for an HTS high current high field cable proposed for EU-DEMO Central Solenoid (CS) hybrid magnet. Every conductor has a specific feature. The aim is to compare the quench behavior of the five conductors “parametrically”. The commissioning of the upgraded facility and the preliminary results of the measurements are presented in this work.
28 April 2022 in IEEE Transactions on Applied Superconductivity
Using a co-wound and insulated NbTi low temperature superconducting (LTS) wire to detect quench in coils wound with high temperature superconducting (HTS) tapes has recently been experimentally proved, yet a theoretical study is still needed to further develop this technique and make it prepared to be applied more generally in high field accelerator magnets. In this manuscript, we present some theoretical and numerical analyses, which confirm a few important facts: 1) It is the significant difference in the temperature dependence of critical current between LTS and HTS but not the normal zone propagation velocity (NZPV), that makes LTSs good quench detectors; 2) LTS quench detectors should have low matrix fraction or high matrix resistivity to increase its normal resistivity and therefore enhance its ability as a quench detector; 3) Heat transfer between cable and detector is important, but a poor heat transfer condition is tolerable; 4) At field beyond 15 T, Nb 3 Sn, Nb 3 Al and MgB 2 all show good potential as quench detectors, and some degradation in wire performance is also acceptable.
16 November 2023 in Superconductor Science and Technology
To explore the potential of iron-based superconducting (IBS) tapes in high-field applications, IBS pancake coils were dry-wound using the uninsulated IBS tape, supplemented with cowound stainless steel tapes for reinforcement. We have successfully fabricated a double pancake coil (DP-1) and a series-connected coil consisting of six DP coils (DP-6). These coils underwent multiple charging tests in a 35 T resistive magnet and retesting in a 14 T superconducting magnet. After conducting multiple rounds of retesting in two different background field magnets, it was found that the IBS coils did not show any degradation in their current-carrying performance. The critical current (I c) value of the DP-1 at 4.2 K and 32 T reached 60 A. To systematically evaluate the I c performance of the six coils in the DP-6, we monitored the V–I curves between 26 voltage taps. The resistive voltage rise was observed at low charging currents, indicating that each coil has suffered different levels of damage. Nevertheless, the overcurrent tests demonstrated that the IBS coil can still carry a current far exceeding its I c without irreversible degradation. We concluded the possible reasons for these phenomena by analyzing the experimental details and test data. In addition, the coil’s internal structure was observed to assess the quality of coil winding, joint soldering, and epoxy resin impregnation. This study will provide references for the electromagnetic and mechanical properties of IBS tapes under ultra-high magnetic fields and contribute to the future development of higher-performance practical IBS coils.
5 May 2023 in Superconductor Science and Technology
The superconducting magnet group at IHEP (the Institute of High Energy Physics, Chinese Academy of Sciences, China) has been engaging in the R&D of high field accelerator magnets since 2014 for the pre-study of the next-generation high energy particle accelerators like CEPC-SPPC (Circular Electron Positron Collider-Super Proton Proton Collider), FCC (Future Circular Collider), etc. A superconducting model dipole magnet named LPF1 was first fabricated with NbTi and Nb3Sn in a combined common-coil configuration in 2017 and tested in 2018, a main field of 10.23 T was reached within two 10 mm apertures. The magnet was reassembled with higher pre-stress in 2019 to investigate the influence of the pre-stress loading level on the performance of common-coil dipole magnets. The main field of this upgraded magnet named LPF1-S was increased to 10.71 T within two 12 mm apertures. By improving the key processing technologies in Rutherford cable fabrication, coil winding, Nb3Sn & NbTi splices soldering and coil impregnation, the recently fabricated model dipole magnet named LPF1-U attained a 12.47 T main field in two 14 mm apertures in 2021. To fully take advantage of Nb3Sn and NbTi superconductors in different field regions, LPF1-U was still designed and developed with a combined coil configuration with Nb3Sn for the inner two coils and NbTi for the outer four coils. Additionally, graded coil topology and different coil LSS (length of straight section) settings were adopted in the optimization of LPF1-U layouts. Bladder and key technology was used for the support structure, and fiber optic sensors based on FBG (fiber Bragg grating) were utilized to monitor the stress distribution and variation in the structures and coils through the whole process from magnet assembly to cool-down and excitation. During the performance test, a relatively large number of trainings were carried out and LPF1-U became more stable after the thermal cycle. A peak field of 12.7 T in the coils (12.47 T main field in apertures) corresponds to an operating current of 6865 A and a load line ratio of 90% was finally attained. It is worth mentioning that LPF1-U is the first hybrid—Nb3Sn, NbTi—common coil dipole magnet that has achieved a main field of more than 12 T in two apertures. The design, fabrication and performance analysis of the LPF series dipole magnets are presented in this paper.
7 October 2022 in Cryogenics