R&D of high field accelerator magnets is ongoing at the Institute of High Energy Physics (IHEP) for pre-study of high energy accelerators in the future. As the first step, a 12-T subscale common-coil dipole magnet named LPF1 (Let the Proton Fly) with two 7 mm apertures and graded coil configuration was designed, fabricated, and tested. With 4 NbTi double-pancake racetrack coils outside and 2 $\rm Nb_{3}Sn$ double-pancake racetrack coils inside, this hybrid dipole magnet was designed to provide a 12-T main field in two apertures operating at 6100 A. The load line ratio is 83 % @ 4.2 k for the designed current and field. To reduce the field enhancement at the ends of the coils, the coils were designed with different lengths. All of the six coils were wound with superconducting Rutherford cables and impregnated with epoxy CTD-101k. Bladders and keys technology was used to pre-stress coils during the assembly of LPF1. A 0.1 Ohm dump resistor and a voltage dependent varistor were used for the quench protection during the test of LPF1. LPF1 was tested at 4.2 K under the self field and a field plateau had been shown around 10.2 T after the $\rm 13^{th}$ quench. The parameters of the design, the process of the fabrication and the test performance of LPF1 are presented in this paper.
28 February 2020 in IEEE Transactions on Applied Superconductivity
Iron-based superconductor (IBS) is expected to be the next generation high temperature superconductor with their potential good properties for the high-field application. This study focus on exploration of the characteristics of IBS coils at high field and development of the IBS coil fabrication technology. A series of diameter 35 mm IBS coils including single pancake (SPC) and double pancakes (DPC) were designed and winded with the 7-filamentary Ba 1-x K x Fe 2 As 2 (Ba122) tape which was produced by the Institute of Electrical Engineering, Chinese Academy of Sciences (IEE-CAS). The IBS coils were divided into 3 groups according to the different fabrication processes. The tests of the IBS coils were firstly carried out at 4.2 K and 10 T background field. The highest quench current of the coils at 10 T is 69.4 A, which is about 90% of the critical current of the short sample at 10 T. Then, two SPCs were selected and tested at 4.2 K at 24 T [1]. The highest quench current of the coils at 24 T is 25.6 A, which is about 39% of the quench current at self-field. The test results were presented and analyzed with respect to the different fabrication processes.
9 November 2018 in IEEE Transactions on Applied Superconductivity
A Nb3Sn/NbTi subscale dipole magnet named LPF1 with graded coil design and common-coil configuration has been designed, assembled and tested at IHEP, China. Compared to the previously proposed FECD1, LPF1 is designed with a longer outer NbTi racetrack coil to reduce the peak field in the coil end. The computed bore field and peak coil field of LPF1 is 12.0 T and 12.1 T if it works at 6100 A with a safety margin of 17% at 4.2 K. The horizontal and vertical directions of the coil packs are preloaded by using bladder & key technology while the axial direction of the coil packs is preloaded by pre-tightening four aluminum rods. Before assembly, we tested the electron-beam welded (EBW) bladders in a subscale shell-support structure and verified the strain measurement system. During assembly, we preloaded the coil packs gradually by referring to the measured shell strain after inserting stainless steel keys and removing the bladders. After assembly, we started to test the subscale dipole magnet vertically at 4.2 K. LPF1 reached a bore field of 10.2 T after 13 training quenches and then it reached a stable quench current without detraining. This paper presents the updated design parameters, the stress analysis, the magnet assembly and test of LPF1.
3 June 2022 in IEEE Transactions on Applied Superconductivity
Epoxy resins are commonly used in high field superconducting magnets for electrical insulation and mechanical reinforcement. However, many of the epoxy systems for vacuum pressure impregnation (VPI) techniques show drawbacks like easy cracking at low temperatures, short pot life, and/or low glass transition temperatures ( T g ), etc . High-field dipole magnets are under development at the Institute of High Energy Physics (IHEP) for the pre-study of future high-energy accelerators. Finding the most appropriate epoxy is critically important. Herein, a new epoxy resin (named IR-3) is developed. Its potting properties including thermal shock, viscosity, T g , and mechanical strength before and after radiation are presented and were compared with CTD-101K which is mostly used in accelerator magnets. Additionally, the thermal and electrical characteristics of high-temperature superconductor (HTS) coils encapsulated with these epoxies were also investigated. The results show that IR-3 is a promising encapsulating material for impregnating HTS coils and has the potential application in high field accelerator magnets.
23 January 2018 in IEEE Transactions on Applied Superconductivity
We carried out the 3D mechanical design of a 2 m-long 20-T common-coil dipole magnet and provided solutions for coil stress management. Instead of using flared ends to make space for the beam pipe, the prototype magnet is designed with a unique configuration which consists of four Nb3Sn and six Bi-2212 racetrack coils. The designed peak coil field is 20.4-T at the operating current of 14,700 A. The operating margin is 11% on the load line at 4.2 K. The magnitude of the calculated Lorentz force for 1/8 model is around 1,562 t, 405 t and 206 t for the horizontal, vertical and axial directions, respectively. The special coil configuration and such significant magnetic force bring unprecedented challenges in applying pre-load to coils and optimizing the coil stress and the stress in the other components. By using an extended Aluminum shell and a split yoke assembly, we minimized the coil end effects and applied a uniform and large enough preload to the coil straight section and the coil ends. This paper presents the stress analysis and the optimized 3D mechanical design of the magnet.
24 February 2022 in IEEE Transactions on Applied Superconductivity
The iron-based superconductor (IBS) is a good candidate for high field magnet applications. The bending effect and properties of IBS tapes were systematically investigated in this work. The bent Ba 1-x K x Fe 2 As 2 (Ba122/Ag/AgSn) 7-filamentary tapes with different bending diameters (D = 10, 15, 20, 25, 30 mm) were prepared by bend-and-react method. A special mechanical structure was used to prevent the heat-treated IBS tapes from being damaged during joint soldering and performance test. The critical current ( I c ) performances of all the bent samples have been tested at 4.2 K and 6-10 T. When the bending diameter is smaller than 30 mm, the transport I c of bent IBS tapes decreases with smaller bending diameters. The average ratio of I c (bent tape) and I c (straight tape) was also calculated. The Optical Microscope Images (OMI) show a lot of cracks that appear regularly in the outermost superconducting core away from the bending center, especially in D10 bent IBS tapes. The magnitude, type, and distribution of the stress in the bent tapes during the bending process were simulated and compared. The causes of the crack formation and the I c reduction in bent IBS tapes were also discussed in detail.