This study aimed to evaluate the surface roughness (Ra; µm), color stability (∆E 00 ), and surface morphology of universal composites after exposure to discoloring solutions. 200 composite discs (2 × 10 mm) were prepared using four paste type (Estelite Asteria, G-aenial A’chord, Filtek Universal, and Filtek Ultimate) and one highly filled flowable (G-aenial Universal Injectable) universal composites (n = 40). Following storage in distilled water, each composite was randomly divided into four subgroups according to the discoloring solutions; black tea, coffee, red wine, and artificial saliva. Baseline, 7, 14, and 21-day color measurements (∆E 00 ) were performed while Ra was evaluated at baseline and 21 days. Data were analyzed using three-way ANOVA and post-hoc Tukey’s tests ( p < 0.05). The correlation between ∆E 00 and Ra was evaluated using Pearson’s correlation test ( p < 0.05). ∆E 00 and Ra were significantly influenced by the composite ( p < 0.001), discoloring solution ( p < 0.001), and the evaluation period ( p < 0.001) while significant interactions were evaluated between the variables for both test methods. For all the composites and evaluation periods, red wine resulted significantly in the highest color change which was followed by black tea and coffee ( p < 0.001). All the composites revealed significantly higher Ra after exposure to discoloring solutions ( p < 0.001). There was a positive correlation between ∆E 00 and Ra with all the tested universal composites ( p = 0.0001). All the tested universal composites revealed clinically unacceptable color change and increased surface roughness after exposure to discoloring solutions. Highly filled flowable universal composite showed the highest color stability in coffee, red wine, and black tea.
This study assessed the repair shear bond strength (SBS; MPa) and surface roughness (Ra; μm) of aged hybrid ceramic (Cerasmart270, GC) and nano-hybrid ceramic (Grandio Blocs, Voco) CAD/CAM blocks after different surface pretreatment methods. In this study, 2 mm thick Cerasmart270 and Grandio Blocs were cut into slabs (Isomet; n = 80 per group). Following aging for six months, the specimens in each CAD/CAM material were randomly divided into four groups (n: 20 each) according to the surface pretreatments: control (no pretreatment), Er:YAG laser, sandblasting, and bur grinding. A total of 10 specimens in each CAD/CAM material pretreatment group were used for Ra evaluation (Perthometer Mahr), while the other 10 were for SBS. After the application of a silane primer (G-Multi Primer, GC) and universal adhesive (G2-Bond, GC), composite build-ups (Filtek Z250; 3MESPE) were performed for the SBS evaluation. After storage in distilled water for 24 h, SBS was evaluated with a universal testing machine (Instron). SBS and Ra data were analyzed with two-way ANOVA and Tukey’s post hoc tests (p < 0.05). SBS was significantly affected by the surface pretreatment methods (p = 0.0001) and by the types of CAD/CAM material (p = 0.005). Bur grinding showed the highest SBS for both CAD/CAM materials, while the control groups yielded significantly lower SBS than bur grinding and sandblasting (p < 0.05). Er:YAG lasers did not significantly enhance the SBS compared to the control group. Sandblasting presented significantly higher SBS than lasers only in Grandio Blocs (p < 0.05). The surface pretreatment methods significantly influenced Ra (p = 0.0001); however, no significant interaction was found between the types of CAD/CAM material and the surface pretreatments (p > 0.05). Control groups exhibited, significantly, the lowest Ra for both materials (p = 0.0001), while no significant differences were observed between the other pretreatment methods. Bur grinding was identified as the most effective pretreatment method for repairing hybrid ceramic CAD/CAM materials.
This study aimed to evaluate the effect of preheating on the push-out bond strength (PBS) and microhardness (HV) of fiber-reinforced flowable and injectable composites and to compare them with dual-cure resin–cement for post cementation. Fifty premolars were endodontically treated, and post spaces were prepared. Specimens were divided into five groups (n = 10) based on the resin luting material. After adhesive application, fiber posts were luted with dual-cure resin–cement (LinkForce), fiber-reinforced flowable composites (EverX Flow; non-heated/preheated), and injectable composites (G-aenial Universal Injectable; non-heated/preheated). After 24 h, roots were sectioned (coronal, middle, apical) for PBS testing (Instron). For HV, 10 specimens per resin luting material were prepared, and top/bottom microhardness was measured to assess the depth of cure. Data were analyzed with two-way ANOVA and post hoc Tukey tests (p < 0.05). Both types of resin luting material and preheating significantly affected PBS and HV (p = 0.0001). Preheated EverX Flow showed significantly higher PBS and HV than LinkForce, while G-aenial Injectable exhibited the lowest values (p < 0.05). Within each resin luting material, PBS significantly decreased from the coronal to the apical region (p = 0.0001). Preheated fiber-reinforced flowable composites demonstrate improved microhardness and adhesion, offering a reliable alternative to the dual-cure resin–cements for fiber post cementation.