A novel Circular Polarized (CP) spatial diversity reception scheme is proposed to mitigate the human-body related fading in off-body communication. Compared to the typical Linear Polarized (LP) diversity receptions, it seems that the proposed scheme can effectively reduce the Root mean square Delay Spread (RDS), Multi-Path Component (MPC) numbers and their variations over different persons and measured locations. Both the signal-level models of LP and CP diversity receptions which take the polarization misalignment into consideration are mathematically derived with the help of diversity gain and cross polarized discrimination (XPD) gain factor. The equal-gaincombination (EGC) signal levels for CP diversity reception are verified to be around 2.1 dB greater than the LP reception, if the polarization mismatch loss is removed. Further, the great signallevel fluctuation caused by the polarization misalignment effect can be mitigated by introducing CP reception when comparing to LP one. The proposed scheme is expected to be useful for designing robust off-body communications.
27 November 2023 in IEEE Antennas and Wireless Propagation Letters
A wideband circularly polarized (CP) substrate integrated waveguide (SIW) cavity-backed stacked dipoles array antenna is proposed for millimeter-wave (mm-wave) applications. Firstly, double-layer SIW cavities are utilized to construct the CP stacked dipole element, which consists of two crossed stacked linearly polarized (LP) electric dipoles and four metallic probes in driven, short-circuited, and suspended states. These probes can achieve orthogonal phase and energy coupling through a magnetic field without additional baluns. Next, wideband CP working principle and parameter analysis of the element are addressed. A full corporate feeding scheme with 4-way SIW power divider and 4 SIW cavities is adopted for array verification. Finally, a 4 × 4 array is designed, fabricated, and measured, which demonstrates wide impedance bandwidth of 28.1%, wide axial ratio (AR) bandwidth of 23%, and a peak gain of 19.35 dBic, respectively. These results demonstrate that the CP stacked dipole is a promising candidate for mm-wave wireless systems.
1 January 2014 in International Journal of Antennas and Propagation
A novel, receiving antenna-height-dependent path loss model under indoor stair environment is presented. The effect of a cross-beam in the stairs is also considered. The proposed model can be applied to describe both of the line-of-sight (LOS) and the non-LOS (NLOS) cases. By using least square criterion, the parameters of proposed model are extracted. Finally, using the maximum likelihood estimation, the precision of the proposed model is evaluated by the standard deviation of shadowing.
The Industrial Internet of things (IIoT) is one of the typical application scenarios in the beyond fifth generation (B5G) wireless communication systems. Due to numerous metal obstacles and machines, the industrial channel, especially at the millimeter-wave (mmWave) bands, exhibits complex characteristics that haven’t been considered in existing literature. This paper proposes an innovative three-dimensional (3D) non-stationary geometry-based stochastic model (GBSM) for IIoT scenarios at mmWave bands. In the proposed model, device reflections (DR) caused by massive metal machines are modeled based on geometrical optics. Furthermore, the generalized extreme value (GEV) distribution and generalized Pareto (GP) distribution are used to parameterize the number of clusters and rays within a cluster, respectively. Further, the Doppler shift is modeled and analyzed using the Gaussian distribution. Some channel statistical characteristics are captured by the proposed model, such as the power delay profile, root-mean-square delay spread, root-mean-square angle spread, inter-cluster delay, and space-time-frequency correlation function. Then, these channel statistical characteristics are well fitted to the ray-tracing simulations and the channel measurements. The excellent fitting results demonstrate the high accuracy of the proposed model, which is crucial for future IIoT communication system design. What’s more, this paper shows the antenna height and propagation scenarios can significantly affect the DR ratio, which should adapt to various IIoT communication scenarios.
Massive robust communication demands among machines and humans are required in ubiquitous Internet of Things (IoTs) applications. To design appropriate communication system, the knowledge of the propagation characteristics for various IoTs scenarios is necessary. In this paper, a measurement-based neural network based root mean square (RMS) delay spread model for ubiquitous indoor IoTs scenarios is presented. The proposed model is a two-layer feed-forward neural network plus a random variable, characterizing the average RMS delay spread and uncertain shadowing effect respectively. The neural network consists of five inputs, including transmitting/receiving antennas (Tx/Rx) separation, frequency, antenna height, environment, and line-of-sight/non-line-of-sight (LOS/NLOS) propagation condition, seven hidden layer neurons and one output layer neuron. Compared with different configurations of the neural network, the hyperbolic tangent sigmoid functions and the Levenberg-Marquardt back propagation algorithm are selected as neurons’ activation functions and training method, respectively. Additionally, the random variable is found to follow the normal distribution using the maximum likelihood estimation. Finally, the novel model is experimentally validated to be accurate, general and extensible compared with the conventional normally distributed RMS delay spread model. This model is well applicable to the design and planning of the ubiquitous communication links for future IoTs scenarios.
Target detection helps to identify, locate, and monitor key components and potential issues in power sensing networks. The fusion of infrared and visible light images can effectively integrate the target the indication characteristics of infrared images and the rich scene detail information of visible light images, thereby enhancing the ability for target detection in power equipment in complex environments. In order to improve the registration accuracy and feature extraction stability of traditional registration algorithms for infrared and visible light images, an image registration method based on an improved SIFT algorithm is proposed. The image is preprocessed to a certain extent, using edge detection algorithms and corner detection algorithms to extract relatively stable feature points, and the feature vectors with excessive gradient values in the normalized visible light image are truncated and normalized again to eliminate the influence of nonlinear lighting. To address the issue of insufficient deep information extraction during image fusion using a single deep learning network, a dual ResNet network is designed to extract deep level feature information from infrared and visible light images, improving the similarity of the fused images. The image fusion technology based on the dual ResNet network was applied to the target detection of sensing insulators in the power sensing network, improving the average accuracy of target detection. The experimental results show that the improved registration algorithm has increased the registration accuracy of each group of images by more than 1%, the structural similarity of image fusion in the dual ResNet network has been improved by about 0.2% compared to in the single ResNet network, and the mean Average Precision (mAP) of the fusion image obtained via the dual ResNet network has been improved by 3% and 6% compared to the infrared and visible light images, respectively.