A wideband circularly polarized (CP) planar U-shaped antenna array is presented for millimeter-wave (mm-wave) applications. First, the antenna element consists of two tilted parasitic U-shaped patches fed by a slot etched on a substrate integrated waveguide (SIW). An improved simulated axial ratio (AR) bandwidth of 40% is achieved by stacking the slot and the patch element. Then, the right- and left-handed orthogonal unit vectors and resonant circuit technique are employed to explain the improved CP operating principle. Finally, an 8 × 8 array is achieved based on the CP element, multiple SIW cavities, and a 16-way SIW feeding network using full-corporate scheme. To verify the design, a prototype is fabricated and measured, which demonstrates a wide impedance bandwidth of 40.4%, a wide AR bandwidth of 31%, a peak gain of 24.6 dBic and supporting dual-CP mode character. The proposed antenna array shows excellent performance and a novel structure, making it a promising candidate for mm-wave wireless systems.
27 November 2023 in IEEE Antennas and Wireless Propagation Letters
A wideband circularly polarized (CP) substrate integrated waveguide (SIW) cavity-backed stacked dipoles array antenna is proposed for millimeter-wave (mm-wave) applications. Firstly, double-layer SIW cavities are utilized to construct the CP stacked dipole element, which consists of two crossed stacked linearly polarized (LP) electric dipoles and four metallic probes in driven, short-circuited, and suspended states. These probes can achieve orthogonal phase and energy coupling through a magnetic field without additional baluns. Next, wideband CP working principle and parameter analysis of the element are addressed. A full corporate feeding scheme with 4-way SIW power divider and 4 SIW cavities is adopted for array verification. Finally, a 4 × 4 array is designed, fabricated, and measured, which demonstrates wide impedance bandwidth of 28.1%, wide axial ratio (AR) bandwidth of 23%, and a peak gain of 19.35 dBic, respectively. These results demonstrate that the CP stacked dipole is a promising candidate for mm-wave wireless systems.
A planar wideband circularly polarized (CP) end-fire antenna is presented for millimeter-wave (mm-wave) applications. First, the antenna consists of an open-ended substrate integrated waveguide (SIW) feeding line in the middle, a pair of stacked substrates with shorted triangular patches on both upper and lower sides, and an offset parallel strip. The shorted triangular patch is viewed as a horizontally polarized electric dipole, while the open-ended SIW is equivalent to an enhanced magnetic dipole due to the stacked substrates. Wide axial ratio (AR) performance is achieved by simultaneously exciting the two dipoles with orthogonal phase supplied by the offset parallel strip. Then, working principle and parameter analysis are explained and discussed for a further understanding. Finally, a prototype is fabricated and measured to verify the design scheme, which demonstrates wideband impedance bandwidth and AR bandwidth performance, novel and efficient radiating structure, simple and small antenna size. This indicates that the proposed antenna is a promising candidate to design wideband end-fire CP antenna in the mm-wave frequency band.
Accuracy improvement of the current sensor is crucial in the electric power industry. In this letter, we present a novel nonintrusive current sensor, based on the tunneling magnetoresistance (TMR) chip, with the feature of simple, low cost, low power consumption, and high accuracy. A stable reference magnetic field, which is generated by the coil, is designed to be mixed with the primary current induced magnetic field and can be detected by the TMR chip simultaneously. An error compensation scheme was introduced based on the reference magnetic field and the error created by the hysteresis is effectively reduced. Experiments were made in which the hysteresis curve, the linearity, the error, and the stability of the sensor were tested. The results show that the errors of our sensor are below 1.46%, when increasing the primary current from 1 to 10 A, which is much less than the TMR chip.
This paper proposed the test technology of traveling wave location device based on the high-speed source of traveling wave, and introduced the embodiment, which use PSCAD, ATP simulation software to create all kinds of transient traveling wave signal data that considered the effect of secondary circuits on the transmit characteristics of wave on the laboratory background PC, and then injected traveling wave signals into the experiment device by using the high-speed source of traveling wave on the site. Traveling wave location tests both in the laboratory and on the site showed that the test technique based on the high-speed source of traveling wave is reliable and accurate.