This paper proposes a comprehensive methodology for Field-Oriented Control (FOC) with parameter variation analysis for Interior Permanent Magnet Synchronous Machines (IPMSM). The modeling approach for an IPMSM is first presented, followed by a step-by-step procedure for designing a vector-controlled strategy. The formulation is based on a dq-rotating reference frame aligned with the rotor shaft position. A key distinction of this methodology from traditional approaches is that the current controller is designed in the time domain based on desired time constants, while the speed control is formulated within a frequency response domain framework. The proposed hybrid approach enables accurate tuning of the Proportional-Integrator (PI) controllers for both current and speed control loops. Additionally, a parameter variation analysis is conducted to enhance the proposed methodology. The validity region for the design procedure is presented, ensuring that for any wide speed variation of the machine, loop gains are properly tuned. One of the main advantages of the proposed methodology is that it provides a fast, reliable, and accurate technique for implementing IPMSM drive systems. Results from a Controller Hardware-in-the-Loop (C-HIL) setup with an external microcontroller are presented. The comprehensive design approach is validated under two different IPMSM parameter sets, demonstrating its effectiveness.
Low voltage direct current (LVDC) system with photovoltaic (PV) source typically contains multiple converters that are used to control the power flow from the PV array to DC loads leading to less end-to-end efficiency, control complexity, reliability issues, voltage regulation challenges, compactness issues, and increased system cost. In this paper, a new power flow architecture is designed for LVDC system that directly connects the PV array to consumer electronics (rated at 24 V) and employs only one front-end bidirectional DC-DC converter between the 24 V load line and the 48 V bus. The bi-directional converter manages load line voltage regulation through a 48 V bus. Under normal conditions, the PV array powers the load while seeking minimal support from the 48 V bus via bi-directional converter, while extensive power is drawn only when the PV output is insufficient for the load requirement, ensuring differential power processing. By introducing a unique power flow layout with a simple design and eliminating intermediate converters, this architecture offers superior end-to-end efficiency, simplified control, and greater reliability compared to previous solutions. To assess theoretical efficiency, a mathematical model of the proposed architecture is also developed. Simulation tests have been conducted, which validate the fundamentals of proposed architecture and indicate its efficiency over 95 % under normal weather conditions. Moreover, the comparative analysis confirms the superior capability of proposed architecture over existing ones. Finally, the functionality of the proposed architecture is verified by experimental prototype.
In this paper, a better power optimizer architecture has been presented for PV strings, using a buck converter for each PV module to address partial shading conditions. The buck converter, though rarely used, is a natural converter for partial shading effects, as it converts the lower current of the shaded module to a higher output current. Usually, the advanced architecture activates the isolated converters (complex) of only shaded modules to draw extra current from the inverter’s DC-link node to maintain the string current (). On the other hand, the conventional architecture activates converters (basic) of all modules regardless of their shading status. The proposed architecture contains a unique design with a new schematic layout, where it activates the buck converters of only shaded modules without drawing extra current from the DC-link. Thus, it combines the benefits of both architectures—selective converter operation, basic topology, high efficiency, low voltage stress, and low control complexity—while eliminating their drawbacks. The designing philosophy, control mechanism, and fundamental operation of the proposed architecture have been comprehensively explained and validated through simulation experiments. Three levels of shading are used to test the proposed architecture for string containing three PV modules: (1) a single module moderate (15%) shading level, (2) a single module strong (50%) shading level, and (3) a double module extreme (75%) and moderate (25%) shading levels. The results show a successful operation of the proposed architecture as it maintains a common for an inverter, where all the shaded modules remain active. The architecture exhibits an average efficiency over 97% under normal conditions. A comparative analysis of architectures has been presented to indicate the enhanced features of the proposed architecture.
This paper presents a standalone system that utilizes a capacitive isolated series resonant converter using an extremum-seeking control algorithm to extract the maximum power from PV panels. While resonant converters have been used for battery charging applications, series resonant converters that utilize capacitive galvanic isolation have not been sufficiently explored, and their design considerations for battery charging have not been established. In addition, extremum-seeking control algorithms have been explored for maximum power point tracking using PWM converters, but not using PFM converters such as resonant converters. This paper lays out the advantages of using an extremum-seeking-based control algorithm with resonant converters, specifically series resonant converters, and it presents simulation results of a 200 W standalone battery charging system to validate the stated benefits.
Adjustable-speed drives (ASD) are extensively adopted in industrial power systems due to their ability to enhance overall efficiency by supplying optimal power to motors based on specific speed and torque requirements. While much existing research focuses on conventional diode rectifiers or voltage-source inverters as front-end solutions, this paper introduces a three-phase power factor correction (PFC) approach using a common DC-link voltage for motor drive applications. This innovative method significantly reduces input current harmonics and improves power factor with minimal active switching components and straightforward control strategies. Furthermore, the DC-link bus can be utilized for multiple motor drives as well. Both analytical and simulation studies validate the effectiveness of the proposed system, demonstrating that the input currents achieve a sine wave form with a unity power factor, while total harmonic distortion of the input current (THDi) is minimized to approximately 2% at the rated power level.