Electron cyclotron emission imaging on EAST provides direct measurements of the 2-D electron temperature dynamics in a continuous large observation area with high temporal and spatial resolution. Besides the normal MHD investigation, a system with a view field large enough to cover the core plasma region has been applied to extract more plasma information, such as the plasma center location, the deposition location of auxiliary heating, and the core toroidal rotation speed. These results solely based on electron cyclotron emission imaging (ECEI) data are consistent with the results of the equilibrium fitting (EFIT), numerical code, and other diagnostics, which indicate the powerful diagnostic capacity of this ECEI system.
1 October 2018 in Review of Scientific Instruments
Electron Cyclotron Emission Imaging (ECEI) is a diagnostic system which measures 2-D electron temperature profiles with high spatial-temporal resolution. Usually only the normalized electron temperature fluctuations are utilized to investigate the magnetohydrodynamics modes due to the difficulties of ECEI calibration. In this paper, we developed a self-dependent calibration method for 24 × 16 channel high-resolution ECEI on the Experimental Advanced Superconducting Tokamak. The technique of shape matching is applied to solve for the matrix of the calibration coefficients. The calibrated area is further expanded to an occupation ratio of 88% observation area by utilizing the features of sawtooth crash. The result is self-consistent and consistent with calibrated 1D ECE measurement.
Pulse thyristors are extensively utilized in pulsed plasma discharge applications. In this study, a pulse switch prototype is built using two parallel valve groups, each consisting of seven series-connected thyristors. Each thyristor is equipped with an anti-parallel protection diode, a static voltage-sharing resistor, and an RCD (resistor-capacitor-diode) dynamic voltage-sharing circuit. The prototype withstands 24 kV, delivers 150 kA peak current, operates at 10 Hz, and can run continuously for 1 s. Thermal analysis is essential under narrow-pulse high-current conditions to avoid failure from localized overheating. By investigating the expansion process of the conduction zone during thyristor turn-on, a single-thyristor turn-on model and a finite-element model of the multi-layer series thyristor module are established to analyze transient temperature distributions. Results show a non-uniform temperature profile across the silicon wafer, with the hottest zone near the gate ring. During repetitive pulses, the silicon temperature fluctuates rapidly, while the copper base heats up gradually. At a spreading speed of 30 m/s, the gate terminal temperature rises about 38 °C—within safe limits for now, but projected to exceed them under future operating conditions. Thus, improved thermal management will be critical in further development.
The rapid increase in plasma core electron temperature triggered by cold plasma injection has long been recognized as compelling evidence of nonlocal transport. This study reports on experiments investigating ‘nonlocal’ thermal transport via compact torus (CT) injection in the plasmas of the EAST tokamak. In low-density plasmas, the core temperature increase following CT injection is accompanied by a drop at the edge. Owing to the CT’s high density, high velocity, and self-organization, rapid penetration into deeper plasma regions was experimentally achieved. In this experiment, the evolution of plasma electron density during CT injection was measured using a high-time-resolution reflectometry for density profile measurement. The evolution of the electron density profile following CT injection is characterized by a rapid increase in core density and subsequent quick flattening of the profile. It has also been found that turbulence plays a crucial role in the mediation of ‘nonlocal’ thermal transport phenomena. The intensity of the quasi-coherent modes (QCMs) in core plasmas, identified by the analysis of Doppler backscattering signals, decreased following CT injection. The simulations based on the trapped gyro-Landau fluid transport model demonstrate that the QCM might be associated with the trapped electron mode (TEM). The observed increase in plasma core temperature after CT injection may be attributed to the stabilization of TEM due to reduction in the core electron density gradient. The simulation results agree well with the experimentally measured core temperature increase after CT injection.
The presence of a bright spot structure in the divertor region during the discharge process, indicative of localized overheating, has been observed through multi-band and high-speed endoscope diagnostic on the Experimental Advanced Superconducting Tokamak (EAST). This localized deposition of hyperthermal heat flux can lead to erosion and melting of the target plate material, thereby posing a significant risk to the safe operation of the device. Moreover, it may introduce impurities into the main plasma, negatively impacting plasma performance. Therefore, real-time monitoring of the divertor and rapid identification of localized overheating regions during experiments are crucial. In this context, this paper proposes an improved DeepLabv3+-based highlight structure image-segmentation algorithm, which uses minimum value, image difference method, and Prewitt operator for dataset preprocessing. In order to realize the rapid identification of local overheated regions, this paper introduces the application of the improved DeepLabv3+ neural network algorithm based on MobileNetV2 as the backbone network in the bright spot structure segmentation task for the first time. The results show that the algorithm achieves a 65.36% average crosslinking rate (mIoU), 78.75% accuracy, 0.78 s per-iteration processing time, and 22.4 MB parameter size. This provides substantial advantages in terms of reduced computing and memory resources and real-time detection performance. Ultimately, the method proposed in this paper enables the rapid identification of the bright spot structure in the localized overheating region of the divertor on the EAST; it identifies areas of overheating and prevents damage to the divertor or other critical components due to overheating, ensuring safe operation of the device.
Compact toroid (CT) injection, with its characteristics of high plasma density and extremely high injection velocity, is considered a highly promising method for core fueling in fusion reactors. Previous studies have lacked investigation into the transport process of CT within drift tubes. To investigate the dynamic processes of CT in drift tubes, this study developed a compressible magnetohydrodynamics (MHD) solver and a magnetic diffusion solver based on the OpenFOAM platform. They were integrated into a multi-region coupling framework to create a multi-region coupled MHD solver, mhdMRF, for simulating the dynamic behavior of CT in drift tubes and its interaction with finite-resistivity walls. The solver demonstrated excellent performance in simulations of the Orszag–Tang MHD vortex problem, the Brio–Wu shock tube problem, analytical verification of magnetic diffusion, and validation of internal coupling boundary conditions. Additionally, this work innovatively explored the effects of the geometric structure at the end of the inner electrode and finite-resistivity walls on the transport processes of CT. The results indicate that optimizing the geometric structure at the end of the inner electrode can significantly enhance the confinement performance and stability of CT transport. The resistivity of the wall profoundly influences the magnetic field structure and density distribution of CT.