Natalia Aleksandra Kowalska

Ms. Natalia Aleksandra Kowalska

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 March 2024 in Polimery
Verified
Journal Article
Open access
PDF file
NKNatalia Aleksandra Kowalska
Natalia Aleksandra Kowalska
Paweł SzczygiełPaweł Szczygieł
Paweł Szczygieł
MSMichal Skrzyniarz
Michal Skrzyniarz
SBSlawomir Blasiak
Slawomir Blasiak
Effect of shells number (1–5) on tensile properties of PLA samples printed using the FDM/FFF technique was investigated. The crack surface was also analyzed. The best properties were obtained for 4-shell sample. However, due to the large coefficient of variation (>> 10%) in the case of elongation, 3-shell sample was selected for testing the machining impact. Such a large coefficient of variation can be explained by the presence of voids between the layers. The greater the number of layers, the greater the structure defects. Machining increases surface smoothness while reducing tensile strength and practically unchanged elongation at break.

31 August 2024
Verified
Book Chapter
Closed access
PDF file
NKNatalia Aleksandra Kowalska
Natalia Aleksandra Kowalska
Paweł SzczygiełPaweł Szczygieł
Paweł Szczygieł
MSMichal Skrzyniarz
Michal Skrzyniarz
SBSlawomir Blasiak
Slawomir Blasiak

14 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
Mateusz RudnikMateusz Rudnik
Mateusz Rudnik
Wiktor SzotWiktor Szot
Wiktor Szot
NKNatalia Aleksandra Kowalska
Natalia Aleksandra Kowalska
Paweł SzczygiełPaweł Szczygieł
Paweł Szczygieł
The study presented an analysis of the behaviour of cellular structures under bending, produced using the PolyJet Matrix (PJM) additive manufacturing method with photopolymer resin. Structures with regular cell geometry were designed to achieve a balance between stiffness, weight reduction, and energy absorption capacity. The aim of this study was to investigate the influence of unit-cell topology (quasi-similar, spiral, hexagonal honeycomb, and their core–skin hybrid combinations) on the flexural properties and deformation mechanisms of PolyJet-printed photopolymer beams under three-point bending. Additionally, all cellular configurations were fully infiltrated with a low-modulus platinum-cure silicone to evaluate the effect of complete polymer–elastomer interpenetration on load-bearing capacity, stiffness, ductility, and energy absorption. All tests were performed according to bending standard on specimens fabricated using a Stratasys Objet Connex350 printer with RGD720 photopolymer at 16 µm layer thickness. The results showed that the dominant failure mechanism was local buckling and gradual collapse of the cell walls. Among the silicone-filled cellular beams, the QS-Silicone configuration exhibited the best overall flexural performance, achieving a mean peak load of 37.7 ± 4.2 N, mid-span deflection at peak load of 11.4 ± 1.1 mm, and absorbed energy to peak load of 0.43 ± 0.06 J. This hybrid core–skin design (quasi-similar core + spiral skin) provided the optimum compromise between load-bearing capacity and deformation capacity within the infiltrated series. In contrast, the fully dense solid reference reached a significantly higher peak load of 136.6 ± 10.2 N, but failed in a brittle manner at only ~3 mm deflection, characteristic of UV-cured rigid photopolymers. All open-cell silicone-filled lattices displayed pseudo-ductile behaviour with extended post-peak softening, enabled by large-scale elastic buckling and silicone deformation and progressive buckling of the thin photopolymer struts. The results provided a foundation for optimising the geometry and material composition of photopolymer–silicone hybrid structures for lightweight applications with controlled stiffness-to-weight ratios.

29 October 2025 in Materials
Verified
Journal Article
Open access
PDF file
NKNatalia Aleksandra Kowalska
Natalia Aleksandra Kowalska
SBSlawomir Blasiak
Slawomir Blasiak
MSMichal Skrzyniarz
Michal Skrzyniarz
Paweł SzczygiełPaweł Szczygieł
Paweł Szczygieł
Wiktor SzotWiktor Szot
Wiktor Szot
Mateusz RudnikMateusz Rudnik
Mateusz Rudnik
Additive manufacturing technologies are characterised by the capability to produce components with complex geometries that are difficult to achieve using conventional methods. Despite the wide range of available materials and additive manufacturing processes, fulfilling design requirements related to surface structure parameters remains a considerable challenge. This paper presents the findings of an investigation into the influence of abrasive treatment of a ferromagnetic fluid on the surface roughness of MEX-printed samples. The samples were fabricated using TPU 95A material. The abrasive medium employed in the study comprised carbonyl iron and silicon carbide. A dedicated tool was designed for the experiments, incorporating neodymium magnets arranged in four asymmetrically distributed slots. The proposed tool represents an unconventional approach in comparison with existing practices. Tests were conducted in three measurement series—B, C, and D—while series A served as the control group. Analysis of the experimental results revealed that, for the parameters Sp (height of the highest apex) and Sz (maximum height, defined as the sum of Sp and Sv, representing the height of the highest apex and the maximum pit depth, respectively), the most significant reduction in parameter values was observed for series D.


17 June 2026 in Materials
Verified
Journal Article
Open access
PDF file
RSRadosław Sójka
Radosław Sójka
PZPiotr Ziarkowski
Piotr Ziarkowski
KKKamil Klamczyński
Kamil Klamczyński
NKNatalia Aleksandra Kowalska
Natalia Aleksandra Kowalska
SBSlawomir Blasiak
Slawomir Blasiak
MSMichal Skrzyniarz
Michal Skrzyniarz
Controlling macro-geometrical errors in the dry drilling of ductile cast iron remains a critical challenge for sustainable and cost-efficient automotive component manufacturing. This paper investigates the influence of cutting speed (vc) and feed per revolution (fn) on the dimensional and shape accuracy of holes drilled in EN-GJS-500-7 ductile cast iron using an HSS DIN 338 helical drill (Ø 11.8 mm, Ceratizit) on an AVIA VMC800 CNC milling centre. A one-factor-at-a-time (OFAT) experimental design was applied: the feed effect was evaluated at vc = 10 m/min with fn ∈ {0.10, 0.15, 0.20} mm/rev, while the speed effect was evaluated at fn = 0.20 mm/rev with vc ∈ {10, 25, 30} m/min. Cutting forces, torques, and vibration accelerations were recorded using an HBM MSC 10 transducer and a PCB 356A01 tri-axial accelerometer. Hole geometry was assessed on a Zeiss Contura G2 coordinate-measuring machine (CMM), and surface texture was evaluated with a TOPO 01P contact profilometer. The expanded measurement uncertainty (k = 2) was estimated based on duplicate test specimens. All drilled holes fell within the IT12 dimensional tolerance (PN-EN 22768-1:1999 grade c), with diameter oversizes ranging from +0.26 mm to +0.46 mm relative to the nominal bore. Cutting speed was identified as the dominant factor affecting both diameter oversize and cylindricity, which increased by 60% (from 0.10 to 0.16 mm) as vc rose from 10 to 30 m/min. Vibration accelerations increased nonlinearly between vc = 25 and 30 m/min (by a factor of 2.5×), indicating an approach to a structural resonance condition. The lowest surface roughness (Ra = 6.6 µm) was obtained at vc = 25 m/min. These findings establish clear physical baselines for tool deflection limits, demonstrating that managing dynamic process stability is vital for optimising macro-geometrical accuracy in the dry machining of cast iron alloys.