Within the double-sided countersunk riveting process of aircraft wings with a composite wedge structure, riveting consistency is poor, and composite damage is severe, which seriously affects the performance and reliability of the aircraft structure. This paper used the principal stress method to establish a stress model of countersunk riveting, and, based on the analysis of the stress on the structure during the pressure-riveting process, a composite structure rivet was designed. A finite element simulation model of the double-sided countersunk riveting of composite wedge structures’ composite rivets was established. The influences of the structure and the matching parameters of composite rivets on both the plastic flow of pressure riveting and the compressive stress of the structure during the pressure-riveting process were analyzed. The structural parameters and riveting process of composite rivets were optimized. The results show that the composite rivet structure could significantly reduce the contact-compressive stress at the riveting joint by more than 20%, thereby reducing the damage caused by the riveting to the composite material. For 4 mm rivets, an aperture of 4.04~4.06 mm can achieve precise relative interference riveting at 0.6% to 1.0%. Employing a 2.6 mm rivet elongation can exactly fill the countersunk hole of the wedge.
According to the requirements for the rapid scanning and measurement of the geometric shape during the process of chemical milling of an aviation engine casing, the scanning path of the casing is planned and studied. This paper introduces the principle and method of the tracking scanner and automatic measuring system and analyzes the scanning area range, approach distance, and wide angle of the field. The casing process is modeled by applying part of the machine, obtaining a series of scanning path point and synthesizing the scanning trajectory. On this basis, the entire scanning process is divided into two alternating actions: scanning measurement and posture adjustment, and the mathematical model of the annular scanning path on the outer surface of the casing part is obtained. Adjusting the scan height was used to solve the repeated scan area problem, and the results show that the adjustment method effectively shortened the scan path’s length and time. The simulation method verifies the planned finite ring-scanning path, which verifies the correctness and feasibility of the mathematical model. Through the automatic scanning reconstruction process test, the reconstruction rate of the ring scanning trajectory reaches 85%, which is 80% higher than the manual detection efficiency.
To address the technical bottlenecks of low path planning efficiency and insufficient point cloud coverage in the automated 3D scanning of complex structural components, this study proposes an offline method for the generation and optimization of scanning paths based on CAD models. Discrete sampling of the model’s surface is achieved through the construction of an oriented bounding box (OBB) and a linear object–triangular mesh intersection algorithm, thereby obtaining a discrete point set of the model. Incorporating a standard vector analysis of the discrete points and the kinematic constraints of the scanning system, a scanner pose parameter calculation model is established. An improved nearest neighbor search algorithm is employed to generate a globally optimized scanning path, and an adaptive B-spline interpolation algorithm is applied to path smoothing. A joint MATLAB (R2023b)—RobotStudio (6.08) simulation platform is developed to facilitate the entire process, from model pre-processing and path planning to path verification. The experimental results demonstrate that compared with the traditional manual teaching methods, the proposed approach achieves a 25.4% improvement in scanning efficiency and an 18.6% increase in point cloud coverage when measuring typical complex structural components. This study offers an intelligent solution for the efficient and accurate measurement of large-scale complex parts and holds significant potential for broad engineering applications.
The aim of manufacturing large aerospace parts for the three-dimensional scanning field demands high precision and efficiency. However, it may be more challenging to meet the full coverage of the measurement problems for large aerospace parts with the scanning range of traditional three-dimensional scanning methods. This paper establishes a dynamic posturing scanning measurement system for large aerospace parts with a six-degree-of-freedom posturing platform and a six-degree-of-freedom industrial robot linkage. It establishes a mathematical model of dynamic three-dimensional scanning posturing. It proposes a platform attitude adjustment strategy based on the field of view angle of a 3D scanner during the adjustment of a six-degree-of-freedom platform. The dynamic scanning path planning is carried out using the three-dimensional spatial decomposition method, and the vector coordinates of the critical points at the edges of the missing areas of the scan are used to re-scan the missing areas to establish the dynamic scanning paths of large aerospace parts. It is experimentally verified that the system can realize the dynamic scanning of complex curved large aerospace parts. The experimental results show that the measurement efficiency is improved by more than 75%, and the point cloud coverage of the scanning reconstruction is improved by 18% for large aerospace components with complex surfaces.
This study employed numerical simulations to investigate the aerodynamic characteristics of a flapping wing by solving the governing incompressible Navier–Stokes equations. Using computational fluid dynamics (CFD), the effect of frequency acceleration on the aerodynamic performance of a two-degrees-of-freedom (DoF) flapping wing in hovering was examined. The results indicate that the pitching frequency acceleration significantly influences the aerodynamic force: positive acceleration enhances lift by up to 2.0 times while maintaining propulsion compared to the case under negative acceleration. This mechanism is attributed to the delayed shedding of the leading-edge vortex (LEV) and the shedding of the trailing-edge vortex (TEV). Moreover, aerodynamic forces are also affected by plunge acceleration, with both negative and positive acceleration contributing to performance improvement. An increase in the acceleration coefficient leads to a notable enhancement in the aerodynamic force; however, the improvement becomes marginal when the coefficient n exceeds 0.4. The underlying flow evolution is illustrated and analyzed through pressure and vorticity contours. These findings on the acceleration effect will be applied to optimize the kinematics and design of flapping wing drones.
Aiming at the engineering problems of the severe wear and limited service life of mandrels during the hole extrusion strengthening of critical aerospace components, this study proposes a surface modification strategy for mandrels based on the anti-friction mechanism of micro-textures. Based on the Lame stress equation and the Mises yield criterion, a plastic strengthening stress distribution model of the hole wall was developed. Integrating Bowden’s adhesive friction theory, a parameterized numerical model was constructed to investigate the influence of micro-texture morphology on interfacial friction and wear behavior. An elastic–plastic contact model for micro-textured mandrels during hole extrusion strengthening was established using ANSYS. The effects of key parameters such as the micro-texture depth and area ratio on the contact pressure field, friction stress distribution, and strengthening performance were quantitatively analyzed. The results show that a circular micro-texture with a depth of 50 μm and an area ratio of 20% can reduce the fluctuation and peak value of the contact pressure by 41.0% and 29.7%, respectively, and decrease the average friction stress by 8.1%. The interfacial wear resistance and the uniformity of the residual compressive stress distribution on the hole wall are significantly enhanced, providing tribological insight and surface optimization guidance for improving the anti-wear performance and extending the service life of mandrels.