Mark Hardy

Dr. Mark Hardy


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 May 2020 in Metallurgical and Materials Transactions A
Verified
Journal Article
Open access
PDF file
MHMark Hardy
Mark Hardy
MDM. Detrois
M. Detrois
EME. T. McDevitt
E. T. McDevitt
CAC. Argyrakis
C. Argyrakis
VSV. Saraf
V. Saraf
STS. Tin
S. Tin
This paper reviews the status of technology in design and manufacture of new wrought polycrystalline Ni-base superalloys for critical engineering applications. There is a strong motivation to develop new alloys that are capable of operating at higher temperatures to realize improvements in thermal efficiency, which are necessary to achieve environmental targets for reduced emissions of harmful green-house gases. From the aerospace sector, the development of new powder metallurgy and ingot metallurgy alloys is discussed for disk rotor and static applications. New compositions for powder metallurgy contain about 50 to 55 pct of gamma prime (γ′) strengthening precipitates to ensure components operate successfully at temperatures up to 788 °C (1450 °F). In contrast, new compositions for ingot metallurgy aim to occupy a design space in temperature capability between Alloy 718 and current powder alloys that are in-service, and show levels of γ′ of about 30 to 44 pct. The focus in developing these alloys was design for manufacturability. To complement the aerospace developments, a review of work to understand the suitability of candidate alloys for multiple applications in Advanced-Ultra Supercritical (AUSC) power plants has been undertaken by Detrois, Jablonski, and Hawk from the National Energy Technology Laboratory. In these power plants, steam temperatures are required to reach 700 °C to 760 °C. The common thread is to develop alloys that demonstrate a combination of high-temperature properties, which are reliant on both the alloy composition and microstructure and can be produced readily at the right price. For the AUSC applications, the emphasis is on high-temperature strength, long-term creep life, phase stability, oxidation resistance, and robust welding for fabrications. Whereas for powder disk rotors in aircraft engines, the priority is enhanced resistance to time-dependent crack growth, phase stability, and resistance to environmental damage, while extending the current strength levels, which are shown by existing alloys, to higher temperatures.

6 August 2014 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
CHC. Herbert
C. Herbert
DAD. A. Axinte
D. A. Axinte
MHMark Hardy
Mark Hardy
PWPhilip John Withers
Philip John Withers
Aero-engine manufacturers are continuously striving to improve component performance and reliability while seeking to increase the efficiency of manufacturing to reduce costs. Efficiency gains by using higher rates of material removal, however, can be counter-productive if they give rise to surface anomalies that distort the material microstructure and reduce the resistance of the material to fatigue crack nucleation. This paper investigates the effect of hole making processes and parameters on surface integrity and the initiation of cracks from low-cycle fatigue (LCF). It reports the dependence of elevated temperature (600 °C) low-cycle fatigue performance of nickel alloy RR1000 from surfaces produced from hole making and subsequent surface conditioning. As-machined surfaces include a reference “damage-free” surface, and two distorted microstructures: (i) a white layer, produced to a depth of 5 and 10 μm and (ii) a distorted gamma prime (γ') structure, produced to a depth of 10 and 15 μm. The effect of shot peening damage-free and 10 μm deep white layer surfaces was also evaluated. It was found that the presence of white layer significantly reduced fatigue performance compared with that shown by the damage-free surface, regardless of whether the white layer was subsequently shot peened or not. In contrast, surfaces showing distorted γ' structures produced much less debit in fatigue life and only from a depth of 15 μm. These results have been rationalized from an examination of fracture surfaces and from measurement of residual stresses before and after fatigue testing. This research is of particular importance as it is among the few reports that quantify the effect of different levels of work piece surface integrity on the fatigue life of a nickel-based superalloy that has been developed for critical rotating components in aero-engine applications.

21 June 2019 in Metals
Verified
Journal Article
Open access
PDF file
AGAmy Goodfellow
Amy Goodfellow
LOLewis R. Owen
Lewis R. Owen
Katerina ChristofidouKaterina Christofidou
Katerina Christofidou
JKJoe Kelleher
Joe Kelleher
MHMark Hardy
Mark Hardy
HSHoward Stone
Howard Stone
The lattice parameters and misfit of the γ and γ′ phases in a series of model quaternary Ni-based superalloys with and without Mo additions have been determined using neutron diffraction between room temperature and 700 °C. Despite the fact that Mo is typically expected to partition almost exclusively to the γ phase and thereby increase the lattice parameter of that phase alone, the lattice parameters of both the γ and γ′ phases were observed to increase with Mo addition. Nevertheless, the effect on the γ lattice parameter was more pronounced, leading to an overall decrease in the lattice misfit with increasing Mo content. Alloys with the lowest Mo content were found to be positively misfitting, whilst additions of 5 at.% Mo produced a negative lattice misfit. A general decrease in the lattice misfit with increasing temperature was also observed.

29 August 2020
Verified
Book Chapter
Closed access
PDF file
MHMark Hardy
Mark Hardy
CAC. Argyrakis
C. Argyrakis
HKH. S. Kitaguchi
H. S. Kitaguchi
AWA. S. Wilson
A. S. Wilson
RBR. C. Buckingham
R. C. Buckingham
HSH. J. Stone
H. J. Stone

30 July 2024 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
SGSimon Gray
Simon Gray
MMM. Mphahlele
M. Mphahlele
DCD. M. Collins
D. M. Collins
CJCatherine Jackson
Catherine Jackson
MHMark Hardy
Mark Hardy
MTM. P. Taylor
M. P. Taylor
Samples of the Ni-based superalloy, RR1000, were exposed to 98% Na2SO4/2% NaCl salts at 700 °C with a flux of 1.5 µg cm−2 h−1 in flowing air + 300 ppm SO2 for a total of 250 h. Three pre-exposure conditions were studied: a bare reference alloy; fast heating to the test temperature followed by a 100 h hold; heating at a rate of 5 °C min−1 to the test temperature following by a 100 h hold. The surface oxide formed under the latter two conditions were Cr2O3 or NiCr2O4, respectively. The results show corrosion pit formation on the surface of the base, reference sample, and no pits present on the sample with the preformed Cr2O3. Some protection was found for the sample heated at 5 °C min−1 with a delay in the progression to accelerated corrosion attack. Additional testing under moisture containing air was also conducted. This showed no obvious difference in surface oxide morphology under the two tested heating rates for the short-term exposures examined but a difference was noted to be dependent on the moisture content of the air.

24 June 2023 in High Temperature Corrosion of Materials
Verified
Journal Article
Open access
PDF file
MTM. P. Taylor
M. P. Taylor
DCD. Calderwood
D. Calderwood
TRT. D. Reynolds
T. D. Reynolds
NWNils Warnken
Nils Warnken
PMP. M. Mignanelli
P. M. Mignanelli
DCD. M. Collins
D. M. Collins
Improved oxidation kinetics for a polycrystalline Ni-based superalloy used in turbine disc applications has been shown to be possible by controlling the heating rate of the first thermal exposure to 5 °C min−1. The beneficial effect arises from the formation of a protective layer of NiCr2O4, instead of the more usually formed doped Cr2O3. This study shows that it was possible to form the NiCr2O4 at temperatures up to 725 °C, within the operational conditions for this alloy, and that at higher temperatures Cr2O3 formed. The improvements in alloy performance extended to the internal oxidation processes where reduced depths of degradation were observed. It is demonstrated here that Al2O3 formation is less thermodynamically stable when the highly protective NiCr2O4 oxide is present at the alloy surface compared to the doped Cr2O3. Synchrotron XRD was performed on samples removed during the heating stage and provided evidence of the oxidation sequence occurring, enabling refinement in the thermodynamic calculations and suggesting an additional route to the formation of the NiCr2O4.