Paweł Telega

Dr. Paweł Telega

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
Kacper ŚwiechowskiKacper Świechowski
Kacper Świechowski
BMBartosz Matyjewicz
Bartosz Matyjewicz
PTPaweł Telega
Paweł Telega
Andrzej BialowiecAndrzej Bialowiec
Andrzej Bialowiec
The proof-of-the-concept of application of low-temperature food waste biochars for the anaerobic digestion (AD) of food waste (the same substrate) was tested. The concept assumes that residual heat from biogas utilization may be reused for biochar production. Four low-temperature biochars produced under two pyrolytic temperatures 300 °C and 400 °C and under atmospheric and 15 bars pressure with 60 min retention time were used. Additionally, the biochar produced during hydrothermal carbonization (HTC) was tested. The work studied the effect of a low biochar dose (0.05 gBC × gTSsubstrate−1, or 0.65 gBC × L−1) on AD batch reactors’ performance. The biochemical methane potential test took 21 days, and the process kinetics using the first-order model were determined. The results showed that biochars obtained under 400 °C with atmospheric pressure and under HTC conditions improve methane yield by 3.6%. It has been revealed that thermochemical pressure influences the electrical conductivity of biochars. The biomethane was produced with a rate (k) of 0.24 d−1, and the most effective biochars increased the biodegradability of food waste (FW) to 81% compared to variants without biochars (75%).

3 April 2024 in Journal of Environmental Management
Verified
Journal Article
Open access
WRwaheed Rasaq
waheed Rasaq
Vaikunthavasan ThiruchenthooranVaikunthavasan Thiruchenthooran
Vaikunthavasan Thiruchenthooran
PTPaweł Telega
Paweł Telega
ŁBŁukasz Bobak
Łukasz Bobak
Chinenye Adaobi IgwegbeChinenye Adaobi Igwegbe
Chinenye Adaobi Igwegbe
Andrzej BialowiecAndrzej Bialowiec
Andrzej Bialowiec
This study employs response surface methodology and a central composite design (CCD) to optimize hydrothermal treatment (HTT) conditions for the valorization of food waste (FW). Lab-scale pressure reactor-based HTT processes are investigated to detect the effects of temperature (220-340 °C) and resident time (90-260 min) on elemental composition and fatty acid recovery in the hydrothermal liquid. Central to the study is the identification of temperature as the primary factor influencing food waste conversion during the HTT process, showcasing its impact on HTT product yields. The liquid fraction, rich in saturated fatty acids (SFA), demonstrates a temperature-dependent trend, with higher temperatures favoring SFA recovery. Specifically, HTT at 340 °C in 180 min exhibits the highest SFA percentages, reaching up to 52.5 wt%. The study establishes HTT as a promising avenue for nutrient recovery, with the liquid fraction yielding approximately 95% at optimized conditions. Furthermore, statistical analysis using response surface methodology predicts the optimal achievable yields for hydrochar and hydrothermal liquid at 6.15% and 93.85%, respectively, obtained at 320 °C for 200 min.

22 August 2025 in Materials
Verified
Journal Article
Open access
PDF file
IRIwona Ryłko
Iwona Ryłko
RZRobert Zarzycki
Robert Zarzycki
ŁBŁukasz Bobak
Łukasz Bobak
PTPaweł Telega
Paweł Telega
DDDidyk-Mucha Didyk-Mucha
Didyk-Mucha Didyk-Mucha
Andrzej BialowiecAndrzej Bialowiec
Andrzej Bialowiec
Biochar (BC), derived from wood biomass through pyrolysis, exhibits properties that make it a promising additive in mortars for sustainable construction. This study investigated the influence of biochar produced at three pyrolysis temperatures (450 °C, 550 °C, and 700 °C) on the performance of cementitious adhesive mortars. The evaluation encompassed physicochemical characterization, mechanical and adhesive strength, volatile organic compound (VOC) emissions, leachability of contaminants, and a life-cycle assessment (LCA). The results demonstrate that biochar obtained at 700 °C has the highest carbon content, an alkaline pH, and increased porosity. In contrast, biochar produced at 450 °C exhibits better sorption capacity and a higher concentration of functional groups. Incorporating 1–5% BC (produced at any temperature) improves mortar performance; however, higher doses negatively affect adhesion to expanded polystyrene board (EPS) and concrete. Emissions of VOCs and leachable metals largely remained within environmental threshold values, with only isolated instances of exceedance. The LCA revealed that substituting mineral fillers with biochar could reduce the carbon footprint by up to 35% compared to the reference formulation. These findings confirm biochar’s potential as a safe and environmentally beneficial component in low-emission construction materials, aligning with the principles of the circular economy and climate-neutral goals.

25 March 2024 in Forests
Verified
Journal Article
Open access
PDF file
ABAdam - Bogacz
Adam - Bogacz
DKDorota Kasowska
Dorota Kasowska
PTPaweł Telega
Paweł Telega
ADAgnieszka Dradrach
Agnieszka Dradrach
Fly ashes produced in huge amounts during coal combustion requires proper management. The purpose of this study was to determine the impact of fly ash from burning hard coal used in large doses (250, 500, 1000 and 2000 t ha−1) on soil properties and vegetation of fresh mixed coniferous forest within 43 years from the ash application. The experiment was established in the Podzols in the forest habitat of Czułów, Katowice Forest district, Upper Silesia, Poland. Eight tree species were planted in ridges created by ploughing: Pinus sylvestris, P. nigra, Larix decidua, Betula pendula, Quercus robur, Q., Acer pseudoplatanus and Fagus sylvatica. The changes in soil morphology caused significant transformations in the physical and chemical properties of the soil such as soil texture, pH, macronutrients (P, K and Mg) content and C:N ratio. Increasing of ash doses changed the granulometric composition of the soil levels from loamy sand (250 t/ha−1) to silt loam (2000 t ha−1). Initially, the acidic Podzols were alkalized under the influence of the fly ash and then acidified, possibly due to the impact of accumulated litter layers, and the reaction of organic soil horizons changed from strongly acidic (250–1000 t ha−1) to alkalis (2000 t/ha−1). The macronutrients content increased in proportion to the fly ash dose, but the subsequent acidification resulted in a gradual decrease in the macronutrients share in the soil layers. The value of the C:N ratio grew after the ash application and then it gradually reduced, even by half. The transformations of soil horizons’ properties also increased the capacity of the soil sorption complex (CEC). All these processes led to a change in the trophic status of the habitat expressed by the soil habitat index (SIG) and the initial coniferous forest site can be classified as a mixed forest habitat even with the lowest ash dose used. The composition of plant communities developed forty years after the ash application was similar at the lower ash doses and the most frequent and abundant tree species were L. decidua, P. nigra and P. silvestris. B. pendula was previously co-dominant, but it was eliminated from the tree stands during the experiment. Planted trees characteristic of late stages of succession, such as Q. robur, Q. rubra, F. sylvatica and A. pseudoplatanus either did not survive or remained in very low quantities. The herb and moss layers developed in the process of spontaneous colonization, and together with the trees led to phytostabilisation of the bare substrates. After acidification of the topsoil horizons, the herb layers consisted mostly of coniferous, mixed, and deciduous forest species, and the most frequent or abundant were Lysimachia europea and Pteridium aquilinum. The moss layers were represented by coniferous forest flora. At the ash dose of 2000 t ha−1, Tilia cordata settled in one of the seral stages of spontaneous succession and this species dominated in the community and formed a dense tree stand. After the soil acidification, a shift from calcicole to calcifuge plant strategy took place among species of the herbaceous layer. The transformations of plant communities’ composition occurred in relation to changes in the soil properties.

2 May 2025 in Materials
Verified
Journal Article
Open access
PDF file
IRIwona Ryłko
Iwona Ryłko
ŁBŁukasz Bobak
Łukasz Bobak
PTPaweł Telega
Paweł Telega
Andrzej BialowiecAndrzej Bialowiec
Andrzej Bialowiec
Combustion and hydrolysis of lignocellulosic biomass generate renewable energy and biofuels, but also yield by-products, such as biomass combustion ash (BCA) and waste lignin (WL). This study investigates the reuse of these by-products in cement mortars, promoting circular economy principles and sustainable construction practices. The addition of BCA at 1–10% improved mortar consistency, homogeneity, and adhesion—most notably, formulations with 5–10% BCA increased adhesion to EPS by up to 4.3%, and compressive strength remained above the 20 MPa threshold. WL additions of 0.5–1% enhanced viscosity and adhesion to both mineral and EPS substrates, with a 0.2% WL dosage improving adhesion to EPS by 9.4% compared to the control sample. Life Cycle Assessment (LCA) confirmed a reduction in the carbon footprint by up to 14% (from 1509.5 to 1297.5 Mg CO2/year), while VOC emissions remained within acceptable limits. Leachability tests confirmed safe environmental performance. The results validate BCA and WL as functional and eco-efficient additives in cementitious composites suitable for thermal retrofitting.

17 September 2025 in Molecules
Verified
Journal Article
Open access
PDF file
ŻCŻaneta Ciastowicz
Żaneta Ciastowicz
RPRenata Pamuła Renata Pamuła
Renata Pamuła Renata Pamuła
EPEdyta Pęczek
Edyta Pęczek
PTPaweł Telega
Paweł Telega
ŁBŁukasz Bobak
Łukasz Bobak
Andrzej BialowiecAndrzej Bialowiec
Andrzej Bialowiec
This work compares reactive (castor) and non-reactive (rapeseed, sunflower, linseed, and used cooking) oils, each at a dosage of 10 wt%, when incorporated into an in-house two-component polyurethane (PU) parquet adhesive. A commercial market adhesive was tested only as an external benchmark and was not modified. Mechanical properties were evaluated according to EN ISO 17178, inorganic leaching according to EN 12457-4, and volatile organics were screened by headspace GC–MS (not comparable to ISO 16000-9 chamber protocols). All in-house formulations met the EN ISO 17178 acceptance limits. The sunflower oil variant showed the highest shear strength, whereas rapeseed and castor oils provided stable tensile performance. HS-GC-MS did not yield high-confidence VOC identifications; therefore, no regulatory emission claim is made. The formulation with used cooking oil exhibited the largest variability and elevated leaching of Zn and Sb, underscoring the need for feedstock quality control. At 10 wt% loading, standard-compliant performance was obtained with both reactive and non-reactive oils, suggesting that physical modification can be sufficient, while castor oil may additionally react. In contrast to derivatized oils reported elsewhere, our approach employs unmodified oils, thereby avoiding extra reaction steps—such as epoxidation, hydroxylation, and transesterification—that typically increase the carbon footprint, while still meeting relevant standards. Full VOC chamber testing and LCA are beyond the scope of this study.