In this study, aluminum single crystals with a {1 0 0} (Cube) orientation were rolled under two conditions: with external constraints imposed by an external aluminum frame (3DRC) and without external constraints (3DR). The crystal plasticity finite element method (CPFEM) was used to simulate texture evolution, and the results corresponded well with experimental observations. The minor discrepancies observed were primarily attributed to the idealized conditions in the simulation. The results demonstrate that in the 3DR model, crystal orientations predominantly rotate around the transverse direction (TD), with non-TD rotations playing a secondary role. In contrast, the 3DRC model exhibits similar rotation patterns to 3DR at lower reductions, but at higher reductions, non-TD rotations become comparable to TD rotations. This difference results in more concentrated orientations in 3DR and more dispersed orientations in 3DRC. Additionally, analysis reveals that external constraints cause deformation behavior to deviate from the plane strain condition rather than move closer to it. The presence of external constraints alters stress and strain states, modifying the activation of slip systems and crystal rotations, leading to significant variations in slip activity, shear strain, and crystal rotation along TD.
CoCrFeMnNi high-entropy alloy (HEA) coatings were fabricated on an S41500 stainless steel substrate by laser cladding and subsequently strengthened using machine hammer peening (MHP) at three hammering energies of 1.7 J, 3.5 J, and 5.0 J. The effects of MHP treatment on the phase structure, surface morphology, microhardness, and tribological properties of the coatings were systematically investigated. The results showed that all coatings retained a single-phase face-centered cubic (FCC) structure after MHP treatment, indicating excellent microstructural stability during impact-induced strengthening. With increasing hammering energy, the surface morphology gradually evolved from discrete hammering indentations to a more continuous orange-peel-like texture, while the surface roughness initially increased and then decreased. MHP significantly enhanced the surface hardness of the coatings. In particular, the MHP3.5 sample exhibited the highest surface hardness of approximately 420 HV, representing an increase of about 120% compared with the untreated coating. Under dry sliding conditions at a load of 30 N, the MHP3.5 sample exhibited the lowest and most stable friction coefficient, maintaining a steady-state value of approximately 0.40–0.45. Its specific wear rate decreased by nearly 45% compared with that of the untreated coating. The improved wear resistance was mainly attributed to the combined effects of strain hardening, grain refinement, and dislocation strengthening induced by machine hammer peening. Considering the hardness, friction coefficient, and specific wear rate results together, a hammering energy of 3.5 J was identified as the most suitable MHP parameter under the low-load wear conditions investigated in this study.
1 September 2025 in Metal Science and Heat Treatment
In this study, the stability of the {112} rolling texture component during asymmetric accumulative roll-bonding (AARB) was systematically investigated using a crystal plasticity finite element method (CPFEM) model. The CPFEM predictions showed that the plastic deformation was inhomogeneous along the thickness for all five asymmetric ratios (1.0, 1.2, 1.5, 0.83, and 0.66). To characterize the plastic deformation and texture evolution, through-thickness shear strain, slip-system shear strain, crystal rotation behaviour, pole figures, and the retained area fraction of the {1 1 2} texture component were analyzed. It was found that the asymmetric ratio, surface friction, and cutting-stacking pattern in AARB played a critical role in the preservation of initial {1 1 2}.
The uniform-field Taylor model, mean-field visco-plastic self-consistent (VPSC), and full-field crystal plasticity finite element method (CPFEM) are three typical and inherently different crystal plasticity (CP) models. In this report, these three CP models were realized within the CPFEM framework via Submodel modeling techniques. In the full-constraint Taylor model, the strain history from the Wholemodel was applied to all finite element method (FEM) nodes, while the strain from the Wholemodel was placed only on the boundaries of the Submodel in the VPSC model. The predicted textures with the Taylor, VPSC, and CPFEM models were compared, and the rolling textures at macroscopic scale were acceptably captured, and the micro-bands were also predicted by the CPFEM and VPSC. Finally, the contribution and limitations of this integrated modeling method were discussed.