Naciri Naciri

Dr. Naciri Naciri

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2021 in Practice Periodical on Structural Design and Construction
Verified
Journal Article
Closed access
PDF file
NNNaciri Naciri
Naciri Naciri
IAIssam AALIL
Issam AALIL
ACAli Chaaba
Ali Chaaba
MAMuzahim Al-Mukhtar
Muzahim Al-Mukhtar
Detailed micromodeling (DMM), macromodeling, and multiscale modeling (MM) as a transitional solution between the two have been extensively used in the last years to model masonry. However, most previous works are based on an advanced theoretical background and/or require a user-defined subroutine, which may restrict their application in engineering practice. This paper proposes a practical and ready-to-use alternative to model and analyze small- and large-scale masonry using DMM and MM. To this end, brick–mortar interfaces were modeled using surface-based cohesive behavior; concrete damaged plasticity was used to model the nonlinear behavior of brick, mortar, and homogenized masonry. These constitutive models have already been implemented in ABAQUS software version 6.14. Mechanical characteristics of the homogenized masonry were derived from simple numerical tests conducted on a representative volume element. Numerical analyses were validated by comparison with experimental results of a confined shear test. It was shown that the DMM provides high accuracy in the simulation of the failure mechanism. The proposed homogenization technique for the MM, on the other hand, provides a satisfactory degree of accuracy with a significant computational cost savings. Both techniques can be used to predict the behavior of masonry at different scales.


18 August 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
SBSaid Beldjilali
Said Beldjilali
Antonella SarcinellaAntonella Sarcinella
Antonella Sarcinella
MOMohamed Amine Ouared
Mohamed Amine Ouared
ABABDELKADER BOUGARA
ABDELKADER BOUGARA
NNNaciri Naciri
Naciri Naciri
Rodica-Mariana IonRodica-Mariana Ion
Rodica-Mariana Ion
Replacing virgin raw materials with recycled waste in construction products is a key strategy for advancing sustainable development. This study explores the partial substitution of commercial gypsum with powdered waste brick (WB) in gypsum mortars, assessing its impact on mechanical performance, water absorption, and environmental footprint. Mortars were prepared with 0%, 5%, 10%, 20%, and 30% WB by weight. Results indicate that a 20% replacement level enhances flexural strength by 56% and compressive strength by 33% at 28 days, compared to the reference mix. SEM and XRD analyses revealed no formation of new crystalline phases, suggesting that the performance improvement is primarily due to physical interactions and microstructural effects. However, at 30% WB, a significant reduction in adhesion strength was observed, falling below the typical threshold for gypsum-based coatings, which may constrain practical application at higher replacement levels. Environmental assessment showed that both CO2 emissions and energy consumption decreased by up to 20% with a 30% substitution. A 20% WB content is therefore proposed as the optimal compromise between mechanical performance and environmental benefit. This approach supports circular economy principles by promoting the reuse of ceramic construction waste in the development of new sustainable materials.

23 September 2026 in Construction and Building Materials
Verified
Journal Article
Closed access
FBFatima Boukabous
Fatima Boukabous
FAFakhr Eddine M’HArzi Alaoui
Fakhr Eddine M’HArzi Alaoui
NNNaciri Naciri
Naciri Naciri
SASomaya Ben Abbou
Somaya Ben Abbou
ACAli Chaaba
Ali Chaaba
IAIssam AALIL
Issam AALIL