Mixed recycled aggregate (MRA) is a kind of recycled aggregate containing discarded bricks and other impurities that is inferior to ordinary recycled concrete aggregate. To study the effect of MRA in concrete, specimens with 100% MRA under different water–cement ratios (W/C) of 0.50, 0.42, 0.36 and 0.30 were prepared, and the mechanical properties and microstructure were tested. Results show that compared with ordinary concrete, the compressive strength of mixed recycled aggregate concrete (MRAC) with the same W/C was reduced by more than 50% at 28 days, but the axial compression ratio was relatively high, reaching over 0.87. Affected by the high water absorption of MRA, the hydration rate of cement slowed, which was beneficial to the long-term development of the properties of MRAC. An appropriate increase in cement content could strengthen MRA and densify the pore structure of MRAC. The research results of this article prove that MRA has high utilization value and could be used to prepare MRAC with application potential using optimal gradation, which is of positive significance for promoting the consumption of construction waste.
19 January 2025 in International Journal of Impact Engineering
To meet the requirements of durability design for concrete suffering frost damage, several test standards have been launched. Among the various damage indexes such as deteriorated compressive strength, relative dynamic elastic modulus (RDEM), residual deformation, etc., the concept of a “Durability Factor” (DF) is proposed by many standards to define the frost resistivity of concrete against frost action based on the experimental results from standard tests. Through a review of the literature, a clear tendency of strength/RDEM decay and residual deformation increase is captured with increasing cycles of freezing and thawing. However, tests following different standards finally derive huge scattering quantitative responses of frost resistance. Based on the large database of available laboratory experiments, this study presents a statistical analysis to propose a predictable model to calculate the DF with respect to other material factors. The statistical model is believed to be more convenient for engineering applications since the time-consuming experiment is no longer needed, and it is more precise compared with that developed according to only single experimental results to cover the uncertainties and unavoidable errors in specific tests. Moreover, the formula to calculate the DF is revised into a more general form so as to be applicable for all the laboratory experiments even for those cases without fully following the standards to derive a DF value.
Incorporating coarse aggregates into ultra-high-performance concrete (UHPC-CA) can reduce material costs, yet reliably predicting its strength-related behavior and overall performance remains challenging. This study examines UHPC-CA through a two-stage orthogonal experimental program comprising 18 mixtures with coarse aggregate, fly ash, and hybrid fiber reinforcements (steel, polypropylene, and composite fibers). Microstructural characterization using scanning electron microscope (SEM) and X-ray computed tomography (X-CT) was conducted to assess interfacial features and crack evolution and to link these observations to the measured mechanical response. Experimentally, fiber reinforcement markedly enhanced post-cracking performance. Compared with the fiber-free control mixture, the optimal hybrid configuration increased flexural strength from 6.9 to 23.5 MPa and compressive strength from 60.1 to 90.5 MPa. The steel–composite fiber system outperformed the steel–polypropylene system, which is consistent with the tighter composite-fiber interfacial bonding observed by SEM/X-CT and supports the feasibility of partially substituting steel fibers. An artificial neural network (ANN) model trained on 50 mixtures and evaluated on 10 unseen mixtures achieved an R2 of 0.9703, an MAE of 1.22 MPa, and an RMSE of 2.11 MPa for compressive strength prediction, enabling sensitivity assessment under multi-factor coupling. Overall, the proposed experiment–characterization–modeling framework provides a data-driven basis for performance-oriented mix design and rapid screening of UHPC-CA.
5 November 2024 in Journal of Building Engineering
In this paper, an intelligent simulation method for chloride ion diffusion behavior in marine concrete is established based on a physical information neural network. The dimensionless constraint equation is constructed to solve the influence of different physical parameter dimensions on the generalization ability of the model. The performance of the simulation method is verified by field measured data. The influence of different exposure ages and chloride ion diffusion coefficients on chloride ion diffusion behavior is quantified. The temporal and spatial distribution characteristics of chlorine ion (C) in concrete under a multi-dimensional diffusion state are analyzed, and the reliability model is further constructed to evaluate the degradation law of the service performance of marine concrete. The results show that the dimensionless physical information neural network model can effectively simulate the diffusion behavior and spatial–temporal distribution of C in marine concrete. The maximum error between the predicted value and the experimental value obtained by the method proposed in this paper is less than 15%. The dimension problem of high-order nonlinear equations can be solved by Non-PINN, with the maximum error value less than 5%. The spatial–temporal distributions of C on different exposed surfaces under a multi-dimensional diffusion state are independent of each other. The service performance of marine concrete will increase with an increase in slag content and protective layer thickness, and decrease with an increase in surface chloride ion concentration.