Film bulk acoustic-wave resonators (FBARs) are widely utilized in the field of radio frequency (RF) filters due to their excellent performance, such as high operation frequency and high quality. In this paper, we present the design, fabrication, and characterization of an FBAR filter for the 3.0 GHz–3.2 GHz S-band. Using a scandium-doped aluminum nitride (Sc0.2Al0.8N) film, the filter is designed through a combined acoustic–electromagnetic simulation method, and the FBAR and filter are fabricated using an eight-step lithographic process. The measured FBAR presents an effective electromechanical coupling coefficient () value up to 13.3%, and the measured filter demonstrates a −3 dB bandwidth of 115 MHz (from 3.013 GHz to 3.128 GHz), a low insertion loss of −2.4 dB, and good out-of-band rejection of −30 dB. The measured 1 dB compression point of the fabricated filter is 30.5 dBm, and the first series resonator burns out first as the input power increases. This work paves the way for research on high-power RF filters in mobile communication.
The lithographically tunable and small size features of Lamb wave resonators (LWRs) take a bright future for their use in high frequency narrow band filters. Resonant frequency drift due to temperature variation has a large impact on the narrower passband and a temperature coefficient of frequency (TCF) closer to 0 can broaden the stable temperature range of the resonator. This paper proposes a method of etching grooves in the area of the piezoelectric layer not covered by the Interdigital transducer (IDT) electrodes to improve the temperature stability of the Lamb resonator. Through the finite element method and theoretical analysis, the phase velocity, group velocity, and TCF dispersion curve of different modes of the resonator with groove structure were determined. The reason for the change of TCF under different normalized thicknesses of AlN was explained through the conversion of the LWR from a contour mode resonator (CMR) to a Cross-Sectional Lamé Mode Resonator. Simulation and test have shown that etching grooves have the effect of reducing TCF by adjusting the electromechanical coupling coefficient. The test shows that 205 nm-depth grooves can lower the TCF of the S0 mode IDT-Open LWR from −13.3 to −5.1 ppm/°C and S1 mode from −36.8 to −9.0 ppm/°C, respectively. The TCF of S0 and S1 mode LWRs decreased by 61.7% and 75.5%, respectively, after 205 nm groove etching. The groove etching method greatly raises the temperature stability of the LWR, enabling Lamb wave filters to operate stably over a wider temperature range.
Bulk acoustic wave (BAW) resonators, with their exceptional high-frequency performance and excellent quality factor, have become a key driver of advances in sensing technology. This study reports the fabrication and characterization of a force sensor based on a solid mounted resonator (SMR) structure. This SMR device utilizes a high resonance frequency of 2.257 GHz as its core sensing element. The operational mechanism involves the application of an external load inducing localized downward mechanical deformation in the SMR film at the pin contact region, thereby generating significant in-plane compressive stress within the piezoelectric layer. The applied strain modifies the intrinsic elastic and piezoelectric constants of the film, thereby changing both the acoustic phase velocity and the electromechanical coupling coefficient (), which ultimately leads to a measurable shift in the resonance frequency. The experimental results reveal a deterministic and robust correlation between the resonance frequency shift and the applied load, which forms a precise function relationship enabling the device to achieve a high sensitivity of 37.79 MHz/N. This indicates that it may possess good application and development potential in various complex industrial fields.
The Lamb wave filter (LWF) has a moderate bandwidth, and the conventional temperature compensation method with one layer of SiO2 on the Lamb wave resonator (LWR) will significantly reduce its effective electromechanical coupling coefficient. This, in turn, narrows the bandwidth of the LWF and limits its application range. This paper achieves high temperature stability for both the LWR and LWF by employing a strategy that combines a double-layer SiO2 and a groove structure based on a Sc0.2Al0.8N film. Finite element analysis is employed to investigate the effect of adding single or double layers of SiO2 films on the temperature stability of the Sc0.2Al0.8N LWR. The simulation results show that applying SiO2 to both the top and bottom of the Sc0.2Al0.8N film can mitigate the reduction in k2 while enhancing temperature stability. The groove structure in the piezoelectric layer can simultaneously improve the temperature coefficient of frequency (TCF) and k2 by altering the electric field distribution and boundary conditions. Measurement results show that the double-layer SiO2 improves the TCF of the LWR to approximately –10 ppm/°C. The grooves can further improve the TCF toward 0 ppm/°C and increase the k2 of LWR.
12 June 2025 in Journal of Physics D: Applied Physics
With the development of communication technology, the demand for high-speed transmission of massive data has imposed increasingly stringent performance requirements on filters. Film bulk acoustic resonators (FBARs) have been widely utilized in radio frequency (RF) filter applications due to their advantages such as high frequency and high quality factor (Q). In this study, we propose the design, fabrication, and characterization of Sc0.2Al0.8N-based film bulk resonators and RF filters. The proposed RF filters are designed for the S-band passband from 3.1 to 3.3 GHz, employing both Mason model circuit simulation and electromagnetic simulation. Through utilizing high-quality Sc0.2Al0.8N film, the measured effective electromechanical coupling coefficient ( ) of the FBAR reaches 10.64%. The measured −3 dB bandwidth of the filter is 223 MHz (spanning from 3.070 GHz to 3.293 GHz), with a low insertion loss of −2.058 dB and an out-of-band suppression of approximately −30 dB. This work demonstrates the potential of Sc0.2Al0.8N thin film bulk acoustic RF filters for S-band applications and provides valuable insights for future advancement in this field.
Lamb wave resonators (LWR) have the advantages of high frequency, small size and lithographically defined resonant frequency. To solve the problems of low effective electromechanical coupling coefficient ( ) and high temperature coefficient of frequency (TCF) in the application of LWR, a method of etching off the AlN film not covered by the top interdigital transducers (IDTs) is proposed to form a Parallel Cross-sectional Lamé Mode Rods Resonator (PCLMRR). The formed rods confine more longitudinal electric field and weaken the lateral capacitance between lateral rods. PCLMRR takes advantage of the high of one order Cross-sectional Lamé Mode Resonator (CLMR) and the low impedance of array structure. The complexity of manufacturing PCLMRR has been reduced by etching grooves using the same mask of IDTs. For the same thickness of AlN film, the critical dimension for PCLMRR in photolithography is twice of CLMR, reducing the demand for photolithography resolution. Compared to plate LWR with a trade-off between TCF and , the PCLMRR adjusts the electric field, capacitance and stress-free boundaries, resulting in a higher and lower TCF simultaneously. The variation of quality factor (Q) with temperature in PCLMRR is also smaller than that of the plate LWR due to the groove cutting the heat flow off and raising the thermal relaxation time.