Krystian Michalczewski

Dr. Krystian Michalczewski

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 July 2022 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
WGWaldemar Gawron
Waldemar Gawron
LKLukasz Kubiszyn
Lukasz Kubiszyn
KMKrystian Michalczewski
Krystian Michalczewski
JPJozef Piotrowski
Jozef Piotrowski
PMPiotr Martyniuk
Piotr Martyniuk
This letter presents InAs $/$ InAsSb-based superlattice (SL) long wavelength (8– $12 \mu \text{m}$ ) range (LWIR) cascade photodetector operating at temperatures > 190 K. The design of the detector resolves the problem of the low quantum efficiency ( QE ) and resistance of the traditional photovoltaic detectors optimized for high temperature (HOT) conditions. The device was deposited by molecular beam epitaxy (MBE) on GaAs substrates with type-II InAs $/$ InAsSb superlattice (T2SLs) absorbers. The constituent stages of the cascade are connected by the low resistance tunnel junctions. Detectivity ( $D^{\ast }$ ) of the unbiased device reaches ~ $6.7\,\,\times10$ 8 cmHz $^{1/2} /\text{W}$ at 210 K, $\lambda $ = $10 \mu \text{m}$ .

1 July 2024 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
MKMałgorzata Kopytko
Małgorzata Kopytko
PMPawel Madejczyk
Pawel Madejczyk
Krzysztof MurawskiKrzysztof Murawski
Krzysztof Murawski
ŁKŁukasz Kubiszyn
Łukasz Kubiszyn
KMKrystian Michalczewski
Krystian Michalczewski
JRJarosław Rutkowski
Jarosław Rutkowski
Four types of barrier detectors based on a type II InAs/InAsSb superlattice with a wide-gap barrier made of a solid AlInAsSb lattice matched to the GaSb buffer were compared. The tested detectors differed in the type of doping of the active layer and the level and type of doping of the contact layer at the barrier. The epitaxial layers were deposited on GaAs (100) substrates using the molecular beam epitaxy method. The spectral and current–voltage characteristics of the analyzed detectors were compared. The highest current responsivities were observed in the structure with a p-type absorber (p+BpN+). Detectors with an n-type absorber (p+Bnn+, n+Bnn+, and nBnn+) show an increase in the current responsivity with an increase in the reverse bias voltage due to the reduction in the undesirable barrier in the valence band. Arrhenius characteristics for the dark current show that only in nBnn+ detectors, it was possible to limit the generation–recombination current. These detectors at 150 K were characterized by the highest normalized detectivity of approximately 3 × 1011 cm · Hz1/2/W. The obtained results were compared with literature data, showing that the parameters of type II superlattice photodetectors are close to those of HgCdTe photodiodes according to the “Rule 07” and “Rule 22” principles.

26 October 2018 in Semiconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
MKMałgorzata Kopytko
Małgorzata Kopytko
EGEmilia Gomółka
Emilia Gomółka
KMKrystian Michalczewski
Krystian Michalczewski
PMPiotr Martyniuk
Piotr Martyniuk
JRJarosław Rutkowski
Jarosław Rutkowski
ARAntoni Rogalski
Antoni Rogalski
In this paper we have investigated dark current sources in high-operating temperature HgCdTe p + B p nN + and InAsSb p + B p nn + and p + B p nN + barrier infrared detectors fabricated using metal organic chemical vapour deposition and molecular beam epitaxy, respectively. The bulk leakage and surface leakage components of the dark current were determined for unpassivated devices fabricated in a round mesa geometry and in different sizes, from 100 to 500 μ m diameters. Results show that the surface leakage current depends on both the conductivity types of the active layers and the semiconductor surfaces. In the InAsSb p + B p nn + detector the bulk component constitutes 100% of the total dark current flowing through the heterostructure. Since the absorber region has the same conductivity type in its bulk and at its surface, the unipolar barrier blocks the current in the bulk, and also blocks the current along the n -type surface of the device. For the HgCdTe p + B p pN + detector, the bulk component constitutes about 50% of the total dark current density in the 200 μ m device operating at 230 K and −0.1 V, whereas for the InAsSb p + B p pN + detector this share is much higher and amounts to 98%. In the HgCdTe detector, the surface leakage current is attributed to the sidewall surfaces along the absorber, as well as depleted surface. In InAsSb, the surface states are pinned into the conduction band, thus the surface current is limited and comes mainly from the depleted area.

9 June 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
LCLukasz Ciura
Lukasz Ciura
AKAndrzej Kolek
Andrzej Kolek
KMKrystian Michalczewski
Krystian Michalczewski
KHKlaudia Hackiewicz
Klaudia Hackiewicz
PMPiotr Martyniuk
Piotr Martyniuk
This article concerns the temperature dependence of low-frequency noise measured in the temperature range of 77–300 K in InAs/InAsSb superlattice photoconductors optimized for long-wavelength infrared (LWIR) and very long-wavelength infrared (VLWIR) spectral range. The differences in the T-dependence and the magnitude of 1/f noise, observed for LWIR and VLWIR photoconductors, are connected with different scattering mechanisms. Using the Hooge empirical model of 1/f noise and modeling of the total mobility, it is suggested that either the phonon-related or the defect-related mobility fluctuations can be responsible for the measured noise depending on the mechanism which determines the total mobility. In the VLWIR photoconductors, the defect-related 1/f noise prevails, while the phonon-related component dominates in the LWIR detector. The latter is best described by the Melkonyan et al. ’s mobility fluctuation model, which assumes the phonon scattering as the origin of 1/f noise. It roughly explains the T-dependence and predicts the value to within the one order of magnitude.

23 January 2020 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
TMTetiana Manyk
Tetiana Manyk
Krzysztof MurawskiKrzysztof Murawski
Krzysztof Murawski
KMKrystian Michalczewski
Krystian Michalczewski
KGKacper Grodecki
Kacper Grodecki
JRJarosław Rutkowski
Jarosław Rutkowski
PMPiotr Martyniuk
Piotr Martyniuk
The type-2 InAs/InAs1−xSbx superlattices on GaAs substrate with GaSb buffer layer were investigated by comparison of theoretical simulations and experimental data. The algorithm for selection of input parameters (binary and ternary materials) for simulations is presented. We proposed the method of the bandgap energy extraction of the absorption curve. The correct choice of the bulk materials and bowing parameters for the ternary alloys allows to reach good agreement of the experimental data and theoretical approach. One of the key achievements of this work was an electron affinity assessment for the device’s theoretical simulation. The detectivity of the long-/very long-wave InAs/InAs1−xSbx superlattice photoconductors at the level of ~ 8 × 109 cm Hz1/2/W (cutoff wavelength 12 µm) and ~ 9 × 108 cm Hz1/2/W (cutoff wavelength 18 µm) at a temperature 230 K confirmed the good quality of these materials.

27 January 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KMKrystian Michalczewski
Krystian Michalczewski
JJJarosław Jureńczyk
Jarosław Jureńczyk
ŁKŁukasz Kubiszyn
Łukasz Kubiszyn
PMPiotr Martyniuk
Piotr Martyniuk
In this paper, we report on the influence of molecular beam epitaxial (MBE) growth temperature on the spectral response of the long-wavelength infrared radiation (LWIR), three-stage thermoelectrically (TE) cooled (T = 210, 230 K) InAs/InAsSb type-II superlattice (T2SL)-based detectors grown on the GaSb/GaAs buffer layers/substrates. Likewise, antimony (Sb) composition and the superlattice (SL) period could be used for spectral response selection. The presented results indicate that the growth temperature affects the 50% cut-off (λ50%cut-off) of the fabricated devices and could be used for operating wavelength tunning. Assuming constant Sb composition and T2SL period during MBE process, the growth temperature is presented to influence λ50%cut-off covering entire LWIR (e.g., temperature growth change within the range of 400–450 °C contributes to the λ50%cut-off ~ 11.6–8.3 μm estimated for operating temperature, T = 230 K). An increase in temperature growth makes a blueshift of the λ50%cut-off, and this is postulated to be a consequence of a modification of the SL interfaces. These results show an approach to the T2SL InAs/InAsSb deposition optimization by the growth temperature in terms of the spectral response, without influencing the T2SLs’ structural properties (Sb composition, SL period).