Maricely De Abreu Rodrigues

Prof. Dr. Maricely De Abreu Rodrigues


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
PSPatricia Santos
Patricia Santos
MIMihaela Iordachescu
Mihaela Iordachescu
MRMaricely De Abreu Rodrigues
Maricely De Abreu Rodrigues
AVAndres Valiente
Andres Valiente
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
This paper addresses the mechanical characterization of dissimilar overlap joints made by autogenous laser welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS) with an optimized welding technology able to produce sound overlap joints. This involved applying the laser beam from the CS-side to reduce the SS overheating. The research is focused on the analysis of combined tensile-shear behavior of the weld and of the heat-affected zones. During testing, the applied tensile-shear load rotates the weld connecting the CS and SS plates. The rotation angle transmitted to the free ends of the plates, together with relevant strain fields, were measured by using a digital image correlation system, VIC-2D. Thus, it was found that the weld acts as a non-linear hinge which experiences a sudden loss of stiffness when strain concentrations develop from the weld ligament edges towards the loaded sides of the plates. The welded joint fails by yielding localization and necking in the CS plate, far from the weld. This mode of failure is a consequence of the weld and heat-affected zone strength mismatches of 1.09 and 1.33, respectively. These values are consistent with the hardness profile and the documented microstructural heterogeneities.

Verified
Journal Article
Open access
PDF file
MIMihaela Iordachescu
Mihaela Iordachescu
PSPatricia Santos
Patricia Santos
AVAndres Valiente
Andres Valiente
MRMaricely De Abreu Rodrigues
Maricely De Abreu Rodrigues
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
This research work addresses the mechanical and metallurgical characterisation, as well as the failure features, of two types of lap-fillet autogenous laser-welded joints made of ultra-thin sheets by applying an appropriate welding technology for producing sound welds and flawless joints. Both welded samples, one made only of stainless steel (SS-SS) sheets, and the other made of stainless steel and carbon steel (SS-CS) plates, were subjected to tensile–shear loads that are representative of the in-service conditions. The experimental research was focused on determining, by the digital image correlation (VIC-2D) method, the strain field and the rotation angle of the welded joints that were developed during loading tests of the welded specimens. Comparing to the classical testing method applied to study the joint overall mechanical properties, the novelty of this research consists of local mechanical behaviour assessment of relevant zones from similar and dissimilar welded joints, by using the innovative technique VIC-2D. Based on the analysis of the experimental results, it was found that the maximum rotation angle is 2.5 times higher in the SS-SS similar welded joint, in comparison with the SS-CS dissimilar welded joint. Despite this finding, the SS-CS specimen failed in the CS base material, far from the weld, with the failure phenomenon being preceded by the material yielding and necking. This failure mode is consistent with the detected strength mismatch of the SS-CS joint, with respect to the CS base material. In contrast, the quasi-ductile fracture of the SS-SS welded joint occurred by plastic exhaustion at the boundary between the narrow Heat-Affected Zone (HAZ) of SS and the Fuzion Zone (FZ). These outcomes are consistent with the hardness profile, microstructural heterogeneities found in the lap-fillet welded joints, and the load versus elongation curves that are determined and discussed in this paper. This research provides new insight and original information on the materials’ response to the autogenous laser welding, which will contribute to improving the knowledge on the ultra-thin lap-fillet welded similar and dissimilar steels.