Gizem Manasoglu

Ms. Gizem Manasoglu

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 January 2021 in Coatings
Verified
Journal Article
Open access
PDF file
GMGizem Manasoglu
Gizem Manasoglu
RCRumeysa CELEN
Rumeysa CELEN
MKMehmet Kanik
Mehmet Kanik
YUYusuf ULCAY
Yusuf ULCAY
In this study, coatings were made with graphene nanopowder in two different thicknesses (0.1 and 0.5 mm) at three different concentrations (50, 100 and 150 g/kg) on polyester woven fabrics. The effects of the coating thickness and graphene concentration were examined with optical and scanning electron microscopy (SEM) images. The thermal stability properties of the samples were also evaluated by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Thermal conductivity was evaluated with two different principles: contact and radiant heat transfer, according to JIS R 2618 and EN ISO 6942, respectively. Solar measurements were performed with a Shimadzu UV-3600 Plus spectrophotometer. The graphene coating improved the thermal stability of the polyester fabrics. The solar absorbance value increased by 80% compared to reference fabrics, and reached approximately 90%. One of the important results was that the thermal conductivity coefficient increased by 87% and 262% for the two coating thicknesses, respectively.

30 May 2024 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
GMGizem Manasoglu
Gizem Manasoglu
RCRumeysa CELEN
Rumeysa CELEN
DKDilayda KANMAZ
Dilayda KANMAZ
In this study, graphene nanoplatelets were applied to polyester fabrics using the knife‐coating method at different concentrations (50, 100, and 150 g/kg). SEM, DSC, and TGA/DTG analyses were performed. The influence of graphene coating on hydrophobicity and surface roughness was examined by water contact angle (WCA) measurement and root mean square roughness, respectively. Abrasion resistance and tear strength tests were also performed. The effect of graphene used as a filler on the flammability of polyester fabric was evaluated for the first time according to the BS 5852 standard. No significant weight loss (only in the range of 0.4%–1.5%) was observed in the graphene‐coated samples even after 100,000 cycles. While the WCA value was 0 for the uncoated fabric, the blind coating and maximum graphene‐coated sample measured 86° and 95°, respectively. The coating process reduced the roughness of the base fabric, and the decrease continued with the increasing graphene ratio. The tear strength values that were 45.5 N in the warp and 53.6 N in the weft direction in the blind coating, increased to 52.2 and 59.1 N, respectively, at the maximum graphene concentration. Graphene coating enhanced thermal stability, increased hydrophobicity, and improved flame retardancy in the test using a smoldering cigarette.

23 November 2024 in Polymers
Verified
Journal Article
Open access
PDF file
DKDilayda KANMAZ
Dilayda KANMAZ
RCRumeysa CELEN
Rumeysa CELEN
EKEsra Karaca
Esra Karaca
GMGizem Manasoglu
Gizem Manasoglu
Herein, composite films were produced by incorporating different amounts (1, 3, 5, and 7%) of barium titanate nanoparticles into the thermoplastic polyurethane matrix using a solution casting method. This study examined the impact of the presence and concentration of a barium titanate additive on morphologic properties, mechanical performance, thermal stability, solar behavior, and wettability of produced film samples. The films were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal gravimetric analysis, scanning electron microscope, ultraviolet-visible near-infrared spectrophotometer, water contact angle, and tensile strength measurements. In the present study, the mass loss of samples containing 7% barium titanate was 24% lower than that of the pure polyurethane reference. The increase of barium titanate rate added to polyurethane enhanced the solar reflectance property of the films, including the near-infrared region. As a prominent result, the transmittance value decreased significantly compared to the reference in the ultraviolet region, and it dropped to 3% for the highest additive concentration. The contact angle values of polyurethane films increased by 11–40% depending on the barium titanate addition ratio. The nano additive also positively affected the mechanical performance of the reference polyurethane film by slightly increasing the tensile strength values.

1 January 2019 in Journal of Engineered Fibers and Fabrics
Verified
Journal Article
Open access
GMGizem Manasoglu
Gizem Manasoglu
MKMehmet Kanik
Mehmet Kanik
KYKenan Yildirim
Kenan Yildirim
In this study, the yellowing behavior of cellulose powders, which is applied to pretreated polyester woven fabrics with concentrations of 100 g/kg by knife coating technique, was investigated. After drying process, coated fabrics were cured at different conditions to determine the effects of the curing temperature and time on yellowing behaviors. The yellowness–whiteness of coated fabrics was measured with a spectrophotometer according to ASTM E313. As the curing temperature and time increase, yellowing effect was more observable. However, the effect of temperature increase is found to be more significant than the increase in curing duration in terms of more observed yellowness. In order to investigate the reason of yellowing, cellulose powder samples were heated in drying oven at three different heating temperatures (130°C, 150°C, and 170°C) for three different heating periods (3, 5, and 7 min). Then, thermal gravimetric analysis and Fourier transform infrared spectroscopy analysis of powder samples were performed for each temperature–period combinations. No ring-opening reaction on the cellulose group was found in the Fourier transform infrared spectroscopy analysis. However, the changes in the spectra can be attributed to the chain breakage in the cellulose macromolecules as well as water loss from the molecular structure during the heating process. Microscopic and scanning electron microscopic analysis was carried out to see any surface change on the fiber and coated fabric. There was no detectable surface change on the fiber and coated fabric surface, apart from a color change on the fabric surface.

20 November 2021 in Materials Science
Verified
Journal Article
Closed access
PDF file
GMGizem Manasoglu
Gizem Manasoglu
RCRumeysa CELEN
Rumeysa CELEN
MAMine Akgun
Mine Akgun
MKMehmet Kanik
Mehmet Kanik
In this article, the surface roughness and friction coefficient values of graphene coated fabrics were examined. Fabrics were coated with three different graphene concentrations (5 %, 10 % and 20 %) with the knife-over-roll principle. The surface roughness of samples was measured by Accretech Surfcom 130A. Various surface roughness parameters of the coated fabrics were evaluated. Static and kinetic friction coefficients of coated fabrics were measured by Labthink Param MXD-02 friction tester using the standard wool abrasive cloth. It was observed that the coating concentration affected the frictional and roughness properties of fabrics. Experimental results showed that fabric surface roughness and friction coefficient values decreased significantly, especially at 20 % concentration. It was concluded that the coated fabrics produced could be used in applications such as anti-wear clothing.

21 January 2026 in Polymers
Verified
Journal Article
Open access
PDF file
DKDilayda KANMAZ
Dilayda KANMAZ
SYSerkan Yıldız
Serkan Yıldız
SKSerpil Koral Koç
Serpil Koral Koç
GMGizem Manasoglu
Gizem Manasoglu
CACansu Aras
Cansu Aras
EKEsra Karaca
Esra Karaca
Essential oils are natural insect repellents, which can be microencapsulated and protected by wall materials to provide prolonged protection against insects. The protection and release of these repellents depend on various parameters, including morphology and production conditions. Herein, twenty-seven gum arabic/citronella essential oil (GA/CEO) spray-dried microcapsules were produced by using three wall-to-core ratios (3:1, 4:1, 6:1), three inlet temperatures (120, 150, 180 °C), and three feed rates (1, 2.5, 5 mL/min). The morphology, particle size, encapsulation efficiency, and release rates were evaluated. The insect repellent activity of microcapsules (0.25, 0.5, and 1 g) against Drosophila melanogaster flies was tested. A systematic process optimization was carried out by evaluating the effects of both emulsion concentration and process parameters on the release rates. Microcapsules with smooth surfaces and homogeneous particle sizes were produced. Encapsulation efficiency reached 90% by increasing the inlet temperature and feed rate. Slower release rates (approximately 40%) were achieved with higher concentrations of the wall material and temperatures, generally. Optimal process conditions were determined as a wall-to-core ratio of 4:1, temperatures exceeding 150 °C, and feed rates above 2.5 mL/min. The highest repellent activity achieved was 95%, indicating effectiveness of GA/CEO microcapsules as insect repellent materials.