The effects of cross-sectional shape on the properties of cationic dyeable poly(ethylene terephthalate) fibres were investigated. Three different cross sections, namely tetra channel, snowflake and hollow, were used. Tensile test results showed that the hollow cross section has the highest breaking strength, while the snowflake has the lowest. In terms of thermal properties, no significant difference was observed. However, some differences in their morphology and surface topography were seen. According to birefringence studies, the hollow cross section has the highest overall orientation, while tetra has the lowest. In addition to this, hollow cross section gives the highest roughness value.
Aim of this study was to investigate the effects of filament cross section on the performance of automotive upholstery fabrics. Thirty-six yarns were produced by changing the cross section of poly(ethylene terephthalate) fibers (round, octolobal and W-channel) and the air-jet texturing parameters (overfeed and number of core and effect yarns). After heat-setting and dyeing the yarns were woven into fabrics and laminated. Performance tests of both the air-jet textured yarns and the fabrics were carried out. It was observed that W-channel gave the most different air-jet textured yarn structure. It formed a bulky, uneven yarn structure with many open loops. No pronounced difference in the recovery from strain behaviors of the air-jet textured yarns was recorded. For all the cross-section types, increase in the looped structure resulted in higher permanent elongation values. In case of fabrics, all the filament cross sections gave satisfactory results for the light fastness and the abrasion resistance tests. It was concluded that changing filament cross section had the most significant effect on air permeability. W-channel gave the lowest air permeability, while octolobal gave the highest one.
1 March 2015 in Journal of Engineered Fibers and Fabrics
Potential applications of atomic force microscopy (AFM) in textiles are explained. For this purpose samples were carefully selected from both natural and synthetic fibers. Cotton, wool, conventional polyethylene terepthalate (PET), antibacterial PET, and antistatic PET were investigated by means of 3D topography imaging, phase imaging, and calculation of their Rq values. The distribution of the additives in the cross sections of antibacterial PET and antistatic PET were analyzed. Moreover, differences between inner and outer cross section of trilobal PET was observed by force spectroscopy. The results are discussed considering the fiber properties. It is concluded that AFM is a powerful tool to investigate different properties of textile fibers, and it gives valuable information.
Essential oils are natural insect repellents, which can be microencapsulated and protected by wall materials to provide prolonged protection against insects. The protection and release of these repellents depend on various parameters, including morphology and production conditions. Herein, twenty-seven gum arabic/citronella essential oil (GA/CEO) spray-dried microcapsules were produced by using three wall-to-core ratios (3:1, 4:1, 6:1), three inlet temperatures (120, 150, 180 °C), and three feed rates (1, 2.5, 5 mL/min). The morphology, particle size, encapsulation efficiency, and release rates were evaluated. The insect repellent activity of microcapsules (0.25, 0.5, and 1 g) against Drosophila melanogaster flies was tested. A systematic process optimization was carried out by evaluating the effects of both emulsion concentration and process parameters on the release rates. Microcapsules with smooth surfaces and homogeneous particle sizes were produced. Encapsulation efficiency reached 90% by increasing the inlet temperature and feed rate. Slower release rates (approximately 40%) were achieved with higher concentrations of the wall material and temperatures, generally. Optimal process conditions were determined as a wall-to-core ratio of 4:1, temperatures exceeding 150 °C, and feed rates above 2.5 mL/min. The highest repellent activity achieved was 95%, indicating effectiveness of GA/CEO microcapsules as insect repellent materials.
5 April 2019 in Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi
Bu çalışmada pamuk ve pamuk/poliester karışımı yüzeylerin antibakteriyel ve antimantar etkinlikleri, hem laboratuvar ortamında ISO 20645, ASTM 2149 ve AATCC 30 standartları kullanıldıktan sonra hem de Uludağ Üniversitesi Tıp Fakültesi Enfeksiyon Hastalıkları Kliniği’nde hem doktorlar hem de hastalar üzerinde ortalama 7 gün kullanıldıktan sonra araştırılmıştır. SEM görüntüleri incelendiğinde, antibakteriyel işlem uygulanmış yüzeylerde gümüş içerikli kimyasalın lif yüzeyinde ince bir film tabakası oluşturduğu açıkça görülmektedir. Antibakteriyel ve antimantar testleri sonrası işlem uygulanmamış yüzeylerin herhangi bir etkinliğe sahip olmadığı görülürken, işlem uygulanmış yüzeylerin kalitatif ve kantitatif testler sonrası hem Staphylococcus aureus’a hem de Escherichia coli’ye karşı ve antimantar test sonuçlarına göre ise Aspergillus niger’e karşı oldukça etkili olduğu tespit edilmiştir. Klinik uygulamaların sonuçlarına göre, antibakteriyel işlem uygulanmış doktor önlükleri ve hastalar için kullanılan çarşafların her iki bakteriye karşı oldukça iyi antibakteriyel etkinliğe sahip olduğu belirlenmiştir. Sonuç olarak antibakteriyel işlem görmüş tekstiller, bakterilerin ve mantarların üremesini engellerken özellikle hastane, otel gibi insan yoğunluğunun fazla olduğu yerlerde kullanımının önemli avantajlar sağlayacağı net olarak görülmektedir.