The dispersion of carbon nanotubes (CNTs) is the bottleneck in CNT-reinforced metal matrix composites. In this work, CNT/Mg composites were prepared by grinding Mg powder and then dispersing CNTs via ball milling and hot pressing. The uniform distribution of Ni-coated CNTs in the matrix was achieved by optimizing the content of CNTs. Scanning electron microscope, high-resolution transmission electron microscopy and X-ray diffraction, optical microscopy, and compression tests were employed. With the CNT content being less than 1%, the CNTs can be evenly distributed in CNT/Mg composites, resulting in a sharp increase in strength. However, with the higher CNT content, the CNTs gradually cluster, leading decreased fracture strain and strength. Furthermore, the coated Ni in the CNTs reacts with the magnesium matrix and completely transforms into Mg2Ni, significantly enhancing the interface bonding. This strong interface bonding and the diffusely distributed Mg2Ni in the matrix significantly strengthen the CNT/Mg composite.
In this paper, CNT/Mg composites with high compressive properties were prepared by using Ni-plated CNT and pure magnesium powder as raw materials through the grinding of magnesium powder, ball-milling mixing and hot-pressing sintering. The effect of grinding time for finer magnesium powder on the microstructure and properties of the final composites was studied mainly by SEM, XRD, HRTEM and compression tests. The results show that with the prolongation of milling time, the magnesium particle size decreases gradually and the CNT dispersion becomes more uniform. Moreover, the nickel layer on the surface of CNT reacts with highly active broken magnesium powder in the sintering process to generate MgNi2 intermediate alloy, which significantly improves interface bonding. The strength and fracture strain of composites are significantly increased by the combined action of the uniform distribution of CNTs and strong interface bonding from the MgNi2 phase. The compressive strength, yield strength and fracture strain of the composites, prepared with a 60 h grinding of magnesium powder, reached 268%, 272% and 279% of those in composites without the grinding of magnesium powder.
The rapid development of fusion-reactor technology calls for excellent anti-irradiation materials. Complex concentrated alloy (CCA) is a newly proposed alloy concept which is a promising candidate of nuclear fusion materials by virtue of its great phase stability under irradiation. This article summarizes anti-radiation mechanism and the microstructure evolution in HEAs. The effective factors on irradiation behavior of HEAs, including entropy, sample size and temperature, are discussed. Finally, the article introduces the potential ways to solve the economic and environmental problems which the HEAs faced for their applications in the future. In summary, the HEAs usually show better irradiation resistance than traditional alloys, such as less swelling, smaller size of defects, and more stable mechanical properties. One possible reason for the irradiation resistance of HEA is the self-healing effect induced by the high-entropy and atomic-level stress among the metal atoms. The activation of the principal element should be considered when selecting components of HEA, and the high throughput technique is a potential way to reduce the design and fabrication cost of HEAs. It is reasonable to expect that coming years will see the application of novel HEAs in fusion reactors.
Grain refinement represents a critical approach in optimizing the as-cast microstructure of magnesium alloys, playing a pivotal role in the development of high-performance magnesium alloys. In the present research, a novel Al-Ce-C-O-Mg grain refiner was fabricated using an innovative rolling-assisted process, and the influence of the grain refiner on the grain size evolution of as-cast AZ91 alloy was systematically examined. The Al-Ce-C-O-Mg grain refiner prepared by the rolling-assisted process contains two types of effective refining particles—MgAl2O4 and Al4C3. These particles can act as potent nucleation sites for α-Mg in the melt, promoting efficient nucleation and achieving significant grain refinement. By adding 1.0 wt.% of the Al-Ce-C-O-Mg grain refiner to the AZ91 alloy, the grain size of the original AZ91 alloy was reduced by 73%. Moreover, adding a refiner facilitated the transformation of the coarse β-Mg17Al12 phase morphologies into a more uniformly distributed and dispersed form. The addition of 1.0 wt.% Al-Ce-C-O-Mg grain refiner to the AZ91 alloy resulted in significant improvements in its mechanical properties. The ultimate tensile strength (UTS), yield strength (YS), and elongation (EL) increased from 158 MPa, 104 MPa, and 3.9% to 203 MPa, 121 MPa, and 6.3%, respectively. The grain refiner developed in this study demonstrates promising potential for application in Mg alloys.
In contrast to practical hot compression processes, the testing of the hot workability of TiAl alloys is usually conducted under the conditions of constant strain rates and constant temperatures. This work aims at investigating the microstructural evolution of TiAl alloys on a Gleeble-3800 thermomechanical simulator under a variable strain rate (0.1, 0.01 and 0.001 s−1) at 1200 °C. The results show that, after a holding time of 30 s, the abrupt change in the strain rate at ε = 0.3 (engineering strain) has a remarkable influence on the flow stress and dynamic recrystallization (DRX) behavior of the β-γ Ti-44Al-6Nb-1Mo-0.3 (B, Y, La, Ce) (at.%) alloy. The flow stress demonstrates a rapid decrease with a sudden reduction in the strain rate. A duplex microstructure of γ + B2/β can be obtained under a high strain rate or continuous medium strain rate. During the two-step deformation, however, both γ→α phase transformation and DRX exist, and the content of the α phase demonstrates a significant increase when the strain rate becomes lower. Finally, a fine-grained structure of γ + B2/β + α2 phases with low residual stresses can be obtained via the two-step heat treatment processes. This provides a promising approach to significantly improve the hot workability of β-γ TiAl alloys.