A vector curvature and temperature sensor based on an in-fiber hybrid microstructure is proposed and experimentally demonstrated. The proposed scheme enables the dimensions of the Fabry–Perot and Mach–Zehnder hybrid interferometer to be adjusted for the formation of the Vernier effect by simply changing the length of a single optical fiber. The sensor is fabricated using a fiber Bragg grating (FBG), multimode fiber (MMF), and a single-hole dual-core fiber (SHDCF). The sensor exhibits different curvature sensitivities in four vertical directions, enabling two-dimensional curvature sensing. The temperature and curvature sensitivities of the sensor were enhanced to 100 pm/°C and −25.55 nm/m−1, respectively, and the temperature crosstalk was minimal at −3.9 × 10−3 m−1/°C. This hybrid microstructure sensor technology can be applied to high-sensitivity two-dimensional vector curvature and temperature detection for structural health monitoring of buildings, bridge engineering, and other related fields.
Phase-stabilized frequency transfer via free-space optical (FSO) links is urgently demanded for high-precision frequency synchronization. However, intensity fluctuations and optical loss in FSO links significantly degrade synchronization precision. We demonstrate a stable frequency synchronization system with low phase noise over a 250-m FSO link. A 100-MHz signal generated by an oven-controlled crystal oscillator is phase-stabilized transferred based on phase-conjugate cancellation. In the FSO link, tip-tilt mirrors are used to suppress beam wander. Meanwhile, a voltage-controlled oscillator is used in the remote site to reduce the phase noise. The phase drift can be reduced from 150 ps to less than 1 ps. Since the phase-locked VCO is used, an ultra-low phase noise of -180 dBc/Hz @ 1 MHz offset is realized and the integrated timing jitter can be reduced to 0.62 ps. The long-term frequency stability and low phase noise may support the synchronization across coherent distributed systems.
In the near-zero negative dispersion region of highly nonlinear fiber, the process of wavelength conversion based on the mechanism of intra-pulse stimulated Raman scattering is sensitive to the parameters of pumping pulse and fiber length under the combined effects of nonlinearity and dispersion. Therefore, we experimentally demonstrate the process in detail by using conventional soliton pulses with three sets of pulse parameters and two highly nonlinear fiber lengths of 400 m and 500 m. The experimental results show that, under the combined action of dispersion and several types of nonlinear mechanisms, the wavelength conversion processes are apparently different when using pulses with different parameters to pump different lengths of highly nonlinear fibers. Specifically, the separation degree of the frequency-shifted pulse spectrum and pumping pulse spectrum, and the corresponding redshift rate and pump power consumption all show significantly different results. The experimental results can guide the selection of more suitable parameters for the pumping pulse and the length of highly nonlinear fiber to achieve a better effect of wavelength redshift or spectrum broadening for various practical applications.
A novel mode-locking method based on nonlinear multimode interference (NLMI) using a distributed large-core (105 μm) graded-index multimode fiber (GIMF)-based saturable absorber (SA) capable of generating four pulse modes is proposed. The distributed SA geometry consists of two GIMFs located at different positions in the resonant cavity. The coupling and joint operation not only facilitate resistance to pulse fragmentation but also provide a sophisticated and widely tunable transmission with saturable and reverse saturable absorption phenomena. Based on this, dissipative soliton (DS), dissipative soliton resonance (DSR), wedge-shaped, and staircase pulses are achieved without additional filters. The DS has accessible output power, pulse energy, bandwidth, and duration of up to 15.33 mW, 2.02 nJ, 22.63 nm, and ~1.68 ps. The DSR has an achievable pulse duration and energy of ~32.39 ns, 30.3 nJ. The dispersion range that allows DS operation is studied, and the dynamics of the evolution from DS to DSR are observed. The versatility, flexibility, and simplicity of the SA device, combined with the possibility of scaling the pulse energy, make it highly attractive for ultrafast optics and nonlinear dynamics.
We experimentally demonstrate an 80 Gbit/s Nyquist-dense wavelength division multiplexed (Nyquist-DWDM) transmission system operating in a simulated atmospheric turbulence channel. The system utilizes eight wavelength-tunable lasers with 100 GHz spacing, modulated by cascaded Mach–Zehnder modulators, to generate phase-locked Nyquist pulse sequences with a 10 GHz repetition rate and a temporal width of 66.7 ps. Each channel is synchronously modulated with a 10 Gbit/s pseudo-random bit sequence (PRBS) and transmitted through controlled weak turbulence conditions generated by a temperature-gradient convection chamber. Experimental measurements reveal that, as the turbulence intensity increases from to , the signal-to-noise ratio (SNR) of the edge channel (C29) and central channel (C33) decreases by approximately 6.5 dB while maintaining stable Nyquist waveform profiles and inter-channel orthogonality. At a forward-error-correction (FEC) threshold of , the minimum receiver sensitivity is −17.66 dBm, corresponding to power penalties below 5 dB relative to the back-to-back condition. The consistent SNR difference (<2 dB) between adjacent channels confirms uniform power distribution and low inter-channel crosstalk under turbulence. These findings verify that Nyquist pulse shaping substantially mitigates phase distortion and scintillation effects, demonstrating the feasibility of high-capacity DWDM free-space optical (FSO) systems with enhanced spectral efficiency and turbulence resilience. The proposed configuration provides a scalable foundation for future multi-wavelength FSO links and hybrid fiber-wireless optical networks.
Ultrafast fiber lasers operating near 2 μm have emerged as a critical platform for advancing mid-infrared photonics due to their narrow pulse durations, high peak powers, and broad tunability. These sources exploit the rich energy-level structures of Tm3+ and Ho3+ doped fibers and reside within an atmospheric transmission window, enabling applications spanning nonlinear microscopy, precision micromachining, optical frequency metrology, biophotonics, and free-space optical communication. Recent progress in low-loss fiber fabrication, dispersion-engineered cavity design, and mode-locking technologies has significantly expanded the performance boundaries of 2 μm ultrafast fiber lasers. This review systematically examines the underlying pulse-formation mechanisms and categorizes state-of-the-art mode-locking approaches. Representative laser architectures are compared with respect to pulse duration, energy scalability, repetition-rate enhancement, spectral characteristics, and environmental stability. Key application pathways in high-resolution spectroscopy, biomedical diagnostics, and mid-IR supercontinuum generation are highlighted. Finally, the remaining challenges and prospective research directions are discussed to inform the development of next-generation ultrafast photonic sources in the 2 μm band.