Aydın Çıtlak

Dr. Aydın Çıtlak

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 November 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
ADAhmet Beyzade DEMIRPOLAT
Ahmet Beyzade DEMIRPOLAT
MUMuhammed Mustafa UYAR
Muhammed Mustafa UYAR
AÇAydın Çıtlak
Aydın Çıtlak
The objective of this study is to investigate the effects of Mn2O3 nanoparticle additives on the performance and emission characteristics of biodiesel fuels produced from vegetable- and waste-based oils. Biodiesel fuels were synthesized via the transesterification process, after which Mn2O3 nanoparticles were blended in different concentrations (50, 75, and 100 ppm). The prepared fuels were tested in a single-cylinder diesel engine operating under constant speed and variable load conditions. Engine performance parameters such as specific fuel consumption (SFC) and thermal efficiency, along with emission indicators including CO, HC, NOx, smoke opacity, and exhaust gas temperature, were systematically analyzed. Additionally, the experimental findings were modeled and validated using the machine learning-based linear regression method. The addition of Mn2O3 nanoparticles significantly improved combustion and emission performance. Among all samples, the COB10+ 100 ppm Mn2O3 fuel exhibited the best overall performance, achieving a 37.50% reduction in CO, 38.8% reduction in HC, and 33.84% reduction in smoke (soot) emissions compared to conventional diesel. This fuel also demonstrated an increase in thermal efficiency comparable to that of diesel. The improvement in thermal efficiency was attributed to enhanced the in-cylinder temperature, reduced ignition delay, and shorter combustion duration. Furthermore, the use of waste-derived vegetable oils contributed to lower production costs and a reduction in environmental impact. The linear regression model yielded an optimum prediction accuracy with a mean squared error of 5.86 × 10−6 for CO emission data. These findings indicate that Mn2O3 nanoparticles can effectively enhance the performance and sustainability of biodiesel fuels while maintaining economic and ecological advantages.

1 May 2026 in Machines
Verified
Journal Article
Open access
PDF file
TKTarkan KOCA
Tarkan KOCA
MEMehmet Bilal Er
Mehmet Bilal Er
AÇAydın Çıtlak
Aydın Çıtlak
Early detection of bearing faults in rotating machinery is essential for ensuring system reliability and effective maintenance planning. Vibration signals inherently contain characteristic fault-related frequency components, providing rich information for both physically interpretable and data-driven analyses. In this study, a multi-representation and correlation-aware feature extraction framework is proposed for automatic classification of bearing faults from vibration signals. Experimental evaluations are conducted using the Case Western Reserve University (CWRU) Bearing Dataset. The dataset includes vibration recordings corresponding to inner race, outer race, ball faults, and healthy conditions under different damage severities. The proposed approach first applies Variational Mode Decomposition (VMD) to suppress noise and enhance frequency-related characteristics. Three different feature representations are then constructed: analytical spectral descriptors, raw Transformer-based deep representations, and a hybrid feature vector obtained by combining these two representations. The hybrid structure is further enhanced through regularized Canonical Correlation Analysis (rCCA), which models the relationship between Transformer representations and spectral descriptors, enabling correlation-aware feature fusion. Spectral, raw Transformer, and rCCA-enhanced hybrid feature vectors are evaluated separately using SVM, Random Forest, and XGBoost classifiers. The results demonstrate that both spectral and Transformer-based representations provide strong performance individually; however, integrating these complementary information sources while modeling their correlations leads to superior and more balanced classification performance. In particular, the rCCA-enhanced hybrid feature vector achieves the best results across all performance metrics. The findings indicate that combining physically meaningful frequency-domain information with data-driven deep representations yields a more robust and generalizable solution for bearing fault diagnosis.

16 March 2026 in Molecules
Verified
Journal Article
Open access
PDF file
MUMuhammed Mustafa UYAR
Muhammed Mustafa UYAR
ADAhmet Beyzade DEMIRPOLAT
Ahmet Beyzade DEMIRPOLAT
AÇAydın Çıtlak
Aydın Çıtlak
This work investigates the influence of hybrid NiO–SiO2 nanoparticles on the engine behavior of biodiesel derived from waste sunflower oil and evaluates the experimental outcomes using a data-driven modeling approach. Biodiesel was produced via transesterification and doped with nanoparticles at concentrations of 50, 75, and 100 ppm. Performance and emission tests were conducted on a single-cylinder diesel engine operating at constant speed under varying loads. Specific fuel consumption, brake thermal efficiency, CO, HC, NOx, smoke opacity, and exhaust gas temperature were recorded and analyzed. The incorporation of nanoparticles improved combustion quality and contributed to substantial reductions in harmful emissions. The WSOB20 blend containing 100 ppm NiO–SiO2 provided the most balanced results, decreasing CO, HC, and smoke emissions by 39.50%, 39.40%, and 35.20%, respectively, relative to diesel fuel, while preserving competitive thermal efficiency. A linear regression model developed for CO prediction produced a low mean squared error (1.08 × 10−5), indicating strong predictive capability. The findings confirm that hybrid nanoparticle additives can enhance biodiesel performance while supporting accurate emission forecasting.

27 September 2019 in Fırat Üniversitesi Mühendislik Bilimleri Dergisi
Verified
Journal Article
Closed access
PDF file
AÇAydın Çıtlak
Aydın Çıtlak
ADAhmet Beyzade DEMIRPOLAT
Ahmet Beyzade DEMIRPOLAT
Mehmet DASMehmet DAS
Mehmet DAS
Tr en
Bu çalışmada, duman borularının çapı 42 mm, baca çapı 230 mm ve su giriş ve çıkış çapları 65 mm olan 125.000 kcal/h ısı kapasiteli katı yakıtlı kazanda, 4 farklı tipte şerit türbülatör kullanılarak ısı transferinin iyileştirilmesi incelenmiştir. Kazandaki duman borularının tümüne yerleştirilen türbülatörlerle deneyler yapılmıştır. İlk olarak içerisine türbülatör yerleştirmeden deneyler yapılmıştır. İkinci adımda ise duman boruları içerisine türbülatörler yerleştirerek her tip için ayrı ayrı deneyler yapılmış ve ısı transferi hesaplanmıştır. Deneylerde fan debisi damper yardımıyla değiştirilerek Reynolds sayısı 1800 ile 2800 arasındaki değerlerde hesaplamalar yapılmıştır. Isı transferi iyileştirmesi için yapılan türbülatörlü deneyler, türbülatörsüz deneylere göre ısı transferinde en az % 44, en fazla % 82 oranında artış sağlanmıştır. Hesaplamalar sonucu elde edilen basınç farkı değerleri için yapay sinir ağı (YSA) kullanılarak tahminsel bir model elde edilmiştir. Elde edilen modelin hata analizleri yapılmış ve basınç değerlerini başarılı bir şekilde tahmin ettiği gösterilmiştir.

In this study, the improvement of heat transfer by using 8 different types of strip turbulators in solid fuel boiler was investigated. The smoke pipes of the boiler used are 42 mm in diameter, the chimney diameter is 230 mm and the water inlet and outlet diameters are 65 mm and the heat capacity is 125,000 kcal / h. Experiments have been carried out with turbulators placed in all smoke pipes in the boiler. Firstly, experiments were carried out without inserting a turbine. In the second step, turbulators were placed in smoke pipes for each type of experiments and heat transfer was calculated. In the experiments, the fan flow rate was changed with the help of damper and the Reynolds number was calculated between 18000 and 28000. For turbine heat exchanger experiments, turbulence tests were carried out and heat transfer was increased by at least 15% and maximum 82%. As a result of the calculations, a predictive model was obtained by using artificial neural network (ANN) for the pressure difference values. The obtained model has been analyzed for error and has been shown to predict the pressure values successfully.

1 March 2021 in Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Verified
Journal Article
Closed access
PDF file
AÇAydın Çıtlak
Aydın Çıtlak
ADAhmet Beyzade DEMIRPOLAT
Ahmet Beyzade DEMIRPOLAT
In smoke pipe boilers, the thermal efficiency of the boiler depends on the smoke pipe diameter, smoke pipe length and the heat transfer between the smoke pipe and the outlet chimney. If the heat in the smoke pipes is effectively transported through the pipes, the heat distribution on the surfaces is balanced and the thermal efficiency of the boiler increases. In this study, the improvement of heat transfer in a solid fuel boiler with 125,000 kcal / h heat capacity with a diameter of 42 mm, chimney diameter of 230 mm and water inlet and outlet diameters of 65 mm was investigated by using 4 different types of strip turbulators. Experiments were carried out with turbulators placed in all the smoke pipes in the boiler. Firstly, experiments were carried out without placing a turbulator inside. In the second step, by placing turbulators in the smoke pipes, experiments were made for each type and heat transfer was calculated. In the experiments, the flow rate of the fan was changed with the help of damper and the reynolds number was calculated between 18000 and 28000. Turbulator experiments for heat transfer improvement have increased by at least %15 and at most %41 compared to turbulator free experiments. For the heat transfer increase values obtained because of calculations, predictive models were obtained using machine learning algorithms SVM (support vector machine) and decision tree (M5P model tree). The resulting models have been analyzed for error analysis and have been shown to successfully predict heat transfer increase values.

26 January 2026 in Adıyaman Üniversitesi Mühendislik Bilimleri Dergisi
Verified
Journal Article
Closed access
MUMuhammed Mustafa UYAR
Muhammed Mustafa UYAR
AÇAydın Çıtlak
Aydın Çıtlak
HVHakan Vural
Hakan Vural
ASAhmet Saylık
Ahmet Saylık
The increasing energy demand and the dwindling fossil fuel reserves are leading to a shift towards alternative energy sources. In this context, the conversion of pressure or vibration-induced irregularities in the environment into electrical energy through piezoelectric materials that generate an electric charge under mechanical stress has been considered. In this study, the possibility of generating electrical energy from transient pressure fluctuations in municipal water distribution lines was investigated using an experimental setup. For this purpose, a laboratory-scale experimental setup consisting of 1-inch diameter pipe elements was created to simulate similar hydraulic conditions observed in urban water networks. PZT-5 and PZT-8 type piezoelectric ceramics were used in a pipeline, electrically isolated from the fluid, and subjected to pressure variations controlled by a ball valve in the range of 1–6 bar. Analysis of the results shows that the highest voltage value is reached at 3 bar with PZT-5 material. With PZT-8 material, a stepped voltage value up to 6 bar is observed. It has been shown that the use of PZT material can provide energy recovery from pressure fluctuations and can be used in water distribution lines.