In modern electrode manufacturing for lithium-ion batteries, the drying of the electrode pastes consumes a considerable amount of space and energy. To increase the efficiency of the drying process and reduce the footprint of the drying equipment, a laser-based drying process is investigated. Evaporation rates of up to 318 g m−2 s−1 can be measured, which is orders of magnitude higher than the evaporation rates in conventional furnace drying processes. Optical measurements of the slurry components in the visible and near-infrared spectrum are conducted. Thermal analyses the of laser-dried samples reveal that the commonly used binders carboxymethyl-cellulose (CMC) and styrene–butadiene rubber (SBR) are not affected by the laser drying process within the investigated process window. The results indicated that with the combination of a fast laser drying step and a subsequent convection drying step, high evaporation rates can be achieved while maintaining the integrity and adhesion of the anode.
Laser-based processing of materials has progressed from traditional applications such as macroscale cutting and welding, to sophisticated techniques, including ultrafast micromachining, additive manufacturing, and surface engineering at micro- and nano-metric scales. Innovations in laser source technology, particularly the advent of high-power and ultrashort-pulse lasers, have expanded the range of processable materials, enabled a plethora of manufacturing applications, and propelled groundbreaking research in optics, photonics, electronics, and biomedical domains. In this article, we provide a concise, yet broad review of the congruent evolution of lasers and materials processing, and highlight seminal developments in the field over the years, combined with a critical assessment of the state of the art. Finally, we also provide an outlook on emerging needs, as well as a roadmap of anticipated developments in laser technologies and materials platforms over the next 50 years. Graphic Abstract
Si/SiGe heterostructures are of high interest for high-mobility transistor and qubit applications, specifically for operations below . In order to optimize parameters such as charge mobility, built-in strain, electrostatic disorder, charge noise, and valley splitting, these heterostructures require Ge concentration profiles close to monolayer precision. Ohmic contacts to undoped heterostructures are usually facilitated by a global annealing step activating implanted dopants, but compromising the carefully engineered layer stack due to atom diffusion and strain relaxation in the active device region. We demonstrate a local laser-based annealing process for recrystallization of ion-implanted contacts in SiGe, greatly reducing the thermal load on the active device area. To quickly adapt this process to the constantly evolving heterostructures, we deploy a calibration procedure based exclusively on optical inspection at room temperature. We measure the electron mobility and contact resistance of laser-annealed Hall bars at temperatures below and obtain values similar or superior to that of a globally annealed reference sample. This highlights the usefulness of laser-based annealing to take full advantage of high-performance Si/SiGe heterostructures.
In this article, we present an approach to fabricate conductive tracks on polymer substrates. Here, a digital printing process is used together with subsequent processing by a laser. For this purpose, a silver flake-based composite is printed onto a polycarbonate substrate using a jet-dispensing process. The printed tracks are then cured using a pyrometer-controlled laser beam source. The fabricated samples are analyzed for electrical resistivity and the cross-sectional area of the conductive tracks and compared to conventionally oven-cured samples. Four-point measurements and an optical measurement method are used for this purpose. Based on the resulting resistance, two different process regimes can be observed for the laser curing process. By using a laser instead of an oven for post-treatment, the achieved resistance of the conductive tracks can be reduced by a factor of 2. Moreover, the tracks produced in this way are more reproducible in terms of the resistance that can be achieved.
We report an image data driven approach for inkjet printing (IJP) to improve the electrical properties of printed metallic strain gauges (SGs). The examined SGs contain narrow conducting paths of multiple orientations and therefore suffer from two challenges: 1. The printing direction of inkjet printed conducting paths has an impact on film formation and electrical properties. 2. A loss-free rotation algorithm for IJP image data is lacking. New ways of IJP image data processing are required to compensate for quality-reducing effects. Novel grid types in terms of loss-free rotation algorithms are introduced. For this purpose, a new grid (e.g., 45° tilted) with a different grid constant is placed over a given pixel grid in such a way that all cell centers of the given pixel grid can be transferred to the rotated grid. Via straightening the tilt, the image data is rotated without interpolation and information loss. By applying these methods to measurement gratings of a full bridge with two perpendicular grating orientations, the influence on the manufacturing quality is investigated. It turns out that the electrical detuning of full bridges can be reduced by one order of magnitude compared to state-of-the-art printing by using so-called diagonal rotation grids.
1 October 2016 in Journal of Microelectronics and Electronic Packaging