tianqiao mao

Dr. tianqiao mao


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 August 2023 in Materials
Verified
Journal Article
Open access
PDF file
XSXiukuo Sun
Xiukuo Sun
SLShouding Li
Shouding Li
XLXiao Li
Xiao Li
GLGuanfang Li
Guanfang Li
BZBo Zheng
Bo Zheng
TMtianqiao mao
tianqiao mao
Shale oil is one of the most promising alternative unconventional energies in the world, and recently the Lucaogou Formation showed significant exploration potential, becoming the primary target in northwestern China. This paper focuses on the mechanical properties and fracture characteristics of shale layered samples from the Lucaogou Formation, conducting uniaxial compressive tests with real-time micro-CT scanning, as well as mineral analysis after failure. It has been found that the mechanical and fracture features are both related to the composition, distribution, content and particle size of minerals, as well as natural fractures. The main crack tends to form in the weak mineral band, for example, calcite or clay band. Since the discontinuous stress usually forms at the interfaces of different minerals, the sample with several major minerals of close content is easier to break into a fractured zone, causing lower uniaxial compressive strength and elastic modulus, compared with the composition of only one dominant mineral. Also, the region will be more fractured after failure if the mineral particles there become smaller. Additionally, although natural cracks have a certain influence on the development of new fractures, not all of the natural ones will propagate into the final fracture network, some of them are just compacted and closed.

26 October 2023 in Energies
Verified
Journal Article
Open access
PDF file
PGPeng Guo
Peng Guo
XLXiao Li
Xiao Li
SLShouding Li
Shouding Li
TMtianqiao mao
tianqiao mao
The economic exploitation of unconventional gas and oil in deep shale relies closely on effective hydraulic fracturing stimulations. However, the fracturing operations of deep shale reservoirs face challenges of insufficient fracture growth and a rapid decline in productivity due to the increasing in situ stress level. In addition, the shale strata on the margin of the Sichuan Basin are frequently folded and faulted, and the change in bedding inclinations significantly complicates the process of hydraulic fracturing. The investigation of the combined effect of the in situ stress level and bedding anisotropy on the hydraulic fracture configuration is vital for fracturing engineering design. To analyze this, we conducted hydraulic fracturing tests on shale cores to simulate the hydraulic fracture initiation and growth from a horizontally positioned perforation. By using acoustic emission detection and CT scans, the influence of natural stress levels and the angle of the shale’s bedding on the process of hydraulic fracturing in shale and the resulting fracture geometry were analyzed. The results showed that the area of hydraulic fracture under a higher stress level (σ1 = 50 MPa, σ3 = 40 MPa) was about 13%~23% smaller than that created under the lower stress level (σ1 = 30 MPa, σ3 = 20 MPa) when the bedding angle was smaller than 60°. With the increase in bedding angle, the curves of the fracture area and fracture network index under two different stress levels presented similar decreasing trends. Also, the time from micro-crack generation to sample breakdown was significantly reduced when the bedding orientation changed from the horizontal to vertical position. The increasing stress level significantly increased the breakdown pressure. In particular, the fracturing of shale samples with bedding angles of 0° and 30° required a higher fluid pressure and released more energy than samples with larger bedding inclinations. Additionally, the measurement of the sample radial deformation indicated that the hydraulic fracture opening extent was reduced by about 46%~81% with the increasing stress level.

24 May 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DWDuo Wang
Duo Wang
XLXiao Li
Xiao Li
GLGuanfang Li
Guanfang Li
TMtianqiao mao
tianqiao mao
BZBo Zheng
Bo Zheng
The pore structure and the petrophysical properties are essential parameters during the marine and continental shale reservoir evaluation. In order to the reveal the mechanism of the pore parameters differences and discuss whether the controlling factors of pore structure have extensive influence in different lithologies. Based on the analysis of N2/CO2 isotherm adsorption, FE-SEM, and geomechanical test for the marine shale samples of Longmaxi Formation and continental shale samples of Yanchang Formation are undertaken. The results indicate that (1) Continental shale is a typical transversely isotropic, while marine shale can be considered a homogeneous rock on a centimeter scale. The lithological stratification is the main reason for the difference in petrophysical properties. (2) The thermal evolution degree has significant influence on the pore structure in shale samples except for TOC content, particularly for the micropores structure. (3) Since the matrix strength of shale is much greater than the strength of bedding planes, the continental shale tends to crack and fail along the weak surface of the bedding during the axial compression, showing a lower peak strength, while the marine shale presents main crack along the principal stress direction without activating the bedding crack.

24 January 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DTDong Tingfa
Dong Tingfa
JZJian Zhou
Jian Zhou
ZYZiqian Yan
Ziqian Yan
YWYanfang Wu
Yanfang Wu
TMtianqiao mao
tianqiao mao
In rock mass engineering, stress balance changes often cause the relative slip of fractures along a wall surface, impacting the seepage behavior of fluid in the fractures. Using computer tomography (CT) scanning, spatial models of fractures with dislocations ranging from 0 to 10 mm were created to explore the relationship between changes in fracture dislocation and changes in fluid flow behavior, respectively. The spatial fractal dimension of cavity distribution within the fractures was calculated using a thin-plate filling approach to characterize the complexity of the fracture cavity distribution. The fluid flow within the dislocation fractures was then simulated using COMSOL, and the effect of cavity alterations in the form of dislocation on the fluid seepage behavior was analyzed using the spatial fractal. The results show that the values of mechanical aperture after dislocation of the fracture obtained by a CT test are normally distributed, the distribution range of mechanical aperture gradually widens with an increase in the dislocation distance, and the average mechanical aperture increases on a logarithmic curve. The relative spatial fractal dimension decreases gradually with an increase in dislocation distance, and the interconnected pathways within the fracture decrease; in addition, it is observed that the change in the relative spatial fractal dimension is closely correlated with the change in the mean mechanical aperture. Numerical simulations of dislocation fracture seepage found that the permeability increases nonlinearly with increasing dislocation distance. When the dislocation distance reaches 5 mm, nonlinear behaviors such as eddy currents occur, and the influence range of eddy currents gradually expands with the increase in dislocation distance under the influence of the boundary. Moreover, the inertia coefficient B in the Forchheimer equation and the critical hydraulic gradient Jc, which can describe the nonlinear seepage characteristics, show a power function decreasing trend with increasing dislocation distance, and the fluid in the fracture is more likely to produce nonlinear flow.

28 November 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YWYixi Wang
Yixi Wang
JCJing Chen
Jing Chen
SLShouding Li
Shouding Li
PZPengfei Zhang
Pengfei Zhang
XCXinshuo Chen
Xinshuo Chen
XLXiao Li
Xiao Li
The occurrence of mountainous geological hazards, primarily including rockfalls, landslides, and debris flows, is frequently influenced by multiple environmental factors and exhibits significant spatial heterogeneity and cumulative effects. To address the need for regional-scale susceptibility assessments within complex geological settings, we propose a novel geological hazard susceptibility assessment model based on conditional probability. This study establishes a dual-module evaluation framework incorporating certainty factors (CFs) and weights (W), in which the CF quantifies the contribution of each factor class to hazard occurrence, while the weights reflect the relative importance of the conditioning factors, thereby improving the model’s capability to characterize multifactorial coupling effects. Using three representative mountainous regions in Xinjiang, China—the Ili Valley Region (IVR), the Northern Piedmont of the Tianshan Mountains (NPTM), and the Kunlun–Altun Mountain Region (KAMR)—we integrate 7938 historical hazard points and 11 conditioning factors within a GIS environment to conduct the assessment. The results reveal regional differences in the weights of conditioning factors: IVR is primarily controlled by Elevation (0.184), Urban-Critical Infrastructure Density (0.163), and Annual Precipitation (0.156); NPTM is dominated by Annual Precipitation (0.153), Urban-Critical Infrastructure Density (0.145), and Road Density (0.136); and KAMR is governed by Elevation (0.197), Seismic Acceleration (0.167), and Hydrogeological Type (0.134). In IVR, NPTM, and KAMR, the Very-High and High susceptibility zones occupy 37.10%, 34.86%, and 26.23% of the land area, respectively, and contain 78.18%, 77.24%, and 82.10% of the identified geological hazards. The region-specific ROC-AUCs are 0.8536 (IVR), 0.8545 (NPTM), and 0.8775 (KAMR), indicating good predictive capability across sedimentary basins and tectonically active zones. This study provides methodological and data support for quantitative risk assessment of geological hazards at the regional scale under complex geological conditions.

27 October 2025 in Fractal and Fractional
Verified
Journal Article
Open access
PDF file
YWYanfang Wu
Yanfang Wu
XLXiao Li
Xiao Li
YU ZOUYU ZOU
YU ZOU
TMtianqiao mao
tianqiao mao
PCPing Chen
Ping Chen
GLGuang Li
Guang Li
Investigating the pore structure and understanding the relationship between pore characteristics and mechanical properties are crucial to research in the study of cement mortar. At present, the segmentation of large-scale concrete pores is mainly conducted using traditional algorithms or software, which are time-consuming and operate in a semi-automated manner. However, the application of these methods faces challenges when analyzing large-scale rock pores due to factors such as a lack of data, artifacts, and inconsistent contrast. In this study, six series of cement mortars were subjected to real-time CT scanning under uniaxial loading (RT-CT) to collect real-time three-dimensional data on the evolution of pore structures during loading. To address issues such as artifacts and inconsistent contrast, a new augmentation method was proposed to overcome artifacts and enhance contrast consistency. Finally, the augmented dataset was utilized for training, and the Fast R-CNN algorithm served as the framework for developing the pore recognition model. The results indicate that the improved algorithm demonstrates enhanced convergence and greater accuracy in pore segmentation. A mathematical model is developed to relate uniaxial compressive strength (UCS) to pore fractal dimension and porosity, based on pore segmentation analysis. The fractal dimensions evolution of each specimen is consistent with the progressive failure indicated by the strain-stress curve. Under uniaxial loading, specimens with a 4:1 cement–sand ratio exhibited peak strength. The incorporation of fractals improved particle contact, thereby facilitating the formation of the skeletal structure. These efforts contribute to improving the identification of the deformation of cement mortars.