This paper provides an introduction to the topic of water shutoff and conformance improvement. After indicating the volumes of water produced during oilfield operations, a strategy is provided for attacking excess water production problems. Problem types are categorized, typical methods of problem diagnosis are mentioned, and the range of solutions is introduced for each problem type. In the third section of the paper, the concept of disproportionate permeability reduction is introduced—where polymers and gels may reduce permeability to water more than to oil or gas. When and where this property is of value is discussed. The fourth section describes the properties of formed gels as they extrude through fractures and how those properties can be of value when treating conformance problems caused by fractures. Section 5 covers the efficiency with which gels block fractures after gel placement—especially, the impact of fluids injected subsequent to the gel treatment.
Summary: Polymer gel has been used for water conformance control for several decades and may have significant potential in remediating unfavorable carbon dioxide (CO2) flow in the subsurface. High-mobility CO2 may channel quickly through sedimentary reservoirs, where unfavorable displacements are worsened in the presence of heterogeneities. Flow diversion technology targeting and withstanding CO2 is therefore essential to improving sweep efficiency and increasing storage potential. Polymer gel treatments have been demonstrated to remediate CO2 channeling in several enhanced oil recovery (EOR) field applications and have been proposed as a means to remediate wellbore and seal leakage during carbon sequestration. The goal of this review is to assess CO2 conformance control by polymer gel in published laboratory work related to both storage and EOR operations. Although field implementation of polymer gel has been successful in reducing CO2 flow, supporting experimental work on the laboratory scale is scattered, with both results and parameters varied. This paper summarizes the available literature and proposes a framework for future experimental work to aid more systematic assessment.
30 September 2022 in Bulletin of the Karaganda University. "Chemistry" Series
Polymer flooding is a promising and effective chemical Enhanced Oil Recovery (cEOR) technology. Polymer flooding is especially cost-effective, whereas other chemical flooding methods, such as Alkaline Surfactant Polymer (ASP), are not profitable and cause serious on-site problems (scaling, uptime decrease, injectivity is-sue, hard-breaking emulsions). Recent papers in the literature mention ~30 field polymer floods. Most of them reported technical success. Although, polymer flooding has been applied ~60 years and it still requires further investigation to provide improvements. Thus, this paper describes important aspects and performances during polymer flooding based on a review of recent projects, combined with the Kalamkas field experience. A comprehensive literature review examines the applicability range in temperature, brine salinity, water source selection, oil properties, formation type, and permeability. Water source selection has an essential role during pilot/field project design and is one of the most responsible technical and economic success decisions. Polymer slug design has been extensively analyzed especially for the high viscosity oil fields; the selected oil/polymer viscosity ratio was usually much less than one. We placed significant emphasis on clarifying ob-served high polymer injectivities. We conducted feasibility studies of some reported ASP floods to clarify that this technology is not profitable at current oil prices. Also, we performed TAN analysis of three Kazakh-stan oil fields for screening of ASP flood.
Summary This paper examines whether retention of partially hydrolyzed polyacrylamide (HPAM) is different under anaerobic vs. aerobic conditions. Both static (mixing with loose sand) and dynamic methods (corefloods) were used to determine HPAM retent
Summary: At the Milne Point polymer flood (North Slope of Alaska), polymer retention is dominated by the clay, illite. Illite, and kaolinite cause no delay in polymer propagation in Milne Point core material, but they reduce the effective polymer concentration and viscosity by a significant amount (e.g., 30%), thus reducing the efficiency of oil displacement until the full injected polymer concentration is regained [which requires several pore volumes (PVs) of throughput]. This work demonstrates that polymer retention on illite is not sensitive to monovalent ion concentration, but it increases significantly with increased divalent cation concentration. The incorporation of a small percentage of acrylamido tertiary butyl sulfonic acid (ATBS) monomers into hydrolyzed polyacrylamide (HPAM) polymers is shown to dramatically reduce retention. The results are discussed in context with previous literature reports. Bridging adsorption was proposed as a viable mechanism to explain our results. Interestingly, an extensive literature review reveals that polymer retention (on sands and sandstones) is typically only modestly sensitive to the presence of oil. Extensive examination of the literature on inaccessible pore volume (IAPV) suggests the parameter was commonly substantially overestimated, especially in rock/sand more permeable than 500 md (which comprises the vast majority of existing field polymer floods).
Polymer gels are frequently applied for conformance improvement in fractured reservoirs, where fluid channeling through fractures limits the success of waterflooding. Placement of polymer gel in fractures reduces fracture conductivity, thus increasing pressure gradients across matrix blocks during chase floods. A gel-filled fracture is re-opened to fluid flow if the injection pressure during chase floods exceeds the gel rupture pressure, thus channeling through the fractures resumes. The success of a polymer gel treatment therefore depends on the rupture pressure. Swelling of gels, e.g. pre-formed particle gels, due to salinity differences between the gel network and surrounding water phase has recently been observed, but the effect has been less studied in conjunction with conventional polymer gels. Using core floods, this study demonstrates that low-salinity water can swell conventional Cr(III)-acetate HPAM gels, thereby improving gel blocking performance after gel rupture. Formed polymer gel was placed in fractured core plugs and chase waterfloods were performed, using four different brine compositions of which three were low-salinity brines. The fluid flow rates through the matrix and differential pressures across the matrix and fracture were measured and shown to increase with decreasing salinity in the injected water phase. In some cores, the fractures were re-blocked during low-salinity waterfloods, and gel blocking capacity was increased above the initial level. Low-salinity water subsequently flooded the matrix during chase floods, which provided additional benefits to the waterflood. The improved blocking capacity of the gel was caused by a difference in salinity between the gel and injected water phase, which induced gel swelling. The results were reproducible through several experiments, and stable for long periods of time in both sandstone and carbonate outcrop core materials. Combining polymer gel placement in fractures with low-salinity chase floods is a promising approach in integrated EOR (IEOR).