Sergiu IVASCU

Dr. Sergiu IVASCU

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 March 2023 in Coatings
Verified
Journal Article
Open access
PDF file
VMValentin Mihailov
Valentin Mihailov
NKNatalia Kazak
Natalia Kazak
SISergiu IVASCU
Sergiu IVASCU
EOEvgenii Ovchinnikov
Evgenii Ovchinnikov
CBConstantin Baciu
Constantin Baciu
Audrius ŽundaAudrius Žunda
Audrius Žunda
The results of systematic studies of the electrospark alloying process with the introduction of dispersed materials into plasma of low-voltage pulsed discharges are presented. Technological methods have been developed for supplying the powder material straight into the treatment zone through a hollow electrode of an anode or from the side, with the electrode-anode periodically contacting the substrate of cathode. It has been established that under the same energy regimes, when powder materials were introduced into the discharge zone, the increase in the mass of the cathode per time unit increases from 10 to 15 times or more. This study presents the process of synthesis of carbide phases (TiC and WC) during electrospark alloying of steel substrates with electrodes made of Ti, W, and graphite, with additional supply powders of these materials into the processing zone. A process has been developed for the synthesis of ternary compounds, so-called MAX-phases: Ti2AlC, Ti2AlN and Ti3SiC2 by electrospark alloying with powder compositions TiAlC, TiAlN and TiSiC. These MAX phases exhibit a unique combination of properties that are characteristic of both metals and ceramics. Energy modes of the processing were optimized, which resulted in high-quality coatings with the maximum content of carbide phases and ternary compounds. It has been established that the energy of electrical pulses during electrospark alloying, when powders of materials are fed into the interelectrode gap, ranges from 0.8 to 3.0 J, depending on their thermal physical properties. High wear and corrosion resistant characteristics of C45 structural steel with such electrospark coatings are obtained. The wear of steel with coatings in comparison with uncoated steel decreased by an average of 5.5–6.0 times. It was estimated the high corrosion resistance of 40X13 steel coated with TiC and WC in 3% NaCl solution. The corrosion current for these coatings is 0.044 and 0.075 A/cm2, respectively, and is significantly less than for coatings made of TiAlC, TiAlN, and TiSiC compositions. X-ray phase and optical metallographic microscopy analyses enabled the display of the amorphous-crystalline nature of the coatings.

6 December 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
Magdalena Valentina LunguMagdalena Valentina Lungu
Magdalena Valentina Lungu
ACAlina Ruxandra Caramitu
Alina Ruxandra Caramitu
Eduard-Marius LungulescuEduard-Marius Lungulescu
Eduard-Marius Lungulescu
VMValentin Mihailov
Valentin Mihailov
SISergiu IVASCU
Sergiu IVASCU
Metal-based electrical contact materials (ECMs) are essential in switching devices and rotating electrical machines, where sliding contacts enable reliable current transmission under motion. These materials must exhibit high conductivity, low friction, and wear resistance to meet industrial demands. However, their reliability is limited by wear, oxidation, arcing, and other failure mechanisms that increase contact resistance and degrade performance. To address these issues, researchers have developed self-lubricating metal matrix composites (MMCs), particularly copper (Cu) and silver (Ag)-based composites reinforced with solid lubricants such as molybdenum disulfide, tungsten disulfide, graphite, carbon nanotubes, graphene, and its derivatives. While Cu and Ag provide excellent conductivity, each has trade-offs in cost, oxidation resistance, and mechanical strength. Strategies for improving reliability involve material optimization, surface treatments, lubrication, contact design modifications, and advanced manufacturing. Although MMCs are widely reviewed, self-lubricating Ag matrix nanocomposites (AgMNCs) for sliding contacts are underexplored. This review highlights recent progress in AgMNCs produced by conventional or modern powder metallurgy techniques, focusing on the role of solid lubricants, testing conditions, and microstructure on tribological performance. Wear mechanisms, research gaps, and future directions are discussed, highlighting pathways toward the development of reliable sliding contacts.

22 June 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
Magdalena Valentina LunguMagdalena Valentina Lungu
Magdalena Valentina Lungu
ACAlina Ruxandra Caramitu
Alina Ruxandra Caramitu
IIIoana Ion
Ioana Ion
Eduard-Marius LungulescuEduard-Marius Lungulescu
Eduard-Marius Lungulescu
Ciprian Alexandru ManeaCiprian Alexandru Manea
Ciprian Alexandru Manea
SISergiu IVASCU
Sergiu IVASCU
Silver (Ag)-based conductive coatings are widely used in electrical contacts due to their excellent electrical conductivity, low contact resistance, good thermal stability and oxidation resistance, although their susceptibility to sulfidation and environmental corrosion is a concern under certain service conditions. In recent years, significant progress has been achieved in both the manufacture and performance optimization of Ag-based coatings to satisfy the demanding requirements of modern electrical and electronic systems. This review summarizes recent advances in fabrication techniques and processing parameters for Ag-based coatings, including electroplating, electroless deposition, magnetron sputtering, electrospark deposition, thermal spraying, and electrical explosion spraying on metallic substrates, particularly on copper and steel substrates. More attention is given to microstructural design strategies, such as the incorporation and homogeneous dispersion of reinforcement or solid lubricant phases within the Ag matrix, to enhance contact reliability and operational endurance. The performance of Ag-based coatings is analyzed in terms of their physical, chemical and mechanical properties, electrical contact resistance, friction and wear behavior, arc erosion resistance, and environmental durability under different service conditions. Key challenges, including coating degradation under high electrical loads, mechanical wear, and corrosive environments, are highlighted. Future research directions are outlined, focusing on multifunctional coating structures that enhance surface performance and ensure the long-term durability of electrical contacts.

18 August 2026 in Surfaces
Verified
Journal Article
Open access
PDF file
Magdalena Valentina LunguMagdalena Valentina Lungu
Magdalena Valentina Lungu
ACAlina Ruxandra Caramitu
Alina Ruxandra Caramitu
IIIoana Ion
Ioana Ion
Eduard-Marius LungulescuEduard-Marius Lungulescu
Eduard-Marius Lungulescu
Ciprian Alexandru ManeaCiprian Alexandru Manea
Ciprian Alexandru Manea
SISergiu IVASCU
Sergiu IVASCU
Silver (Ag)-based conductive coatings are widely used in electrical contacts due to their excellent electrical conductivity, low contact resistance, good thermal stability and oxidation resistance, although their susceptibility to sulfidation and environmental corrosion is a concern under certain service conditions. In recent years, significant progress has been achieved in both the manufacture and performance optimization of Ag-based coatings to satisfy the demanding requirements of modern electrical and electronic systems. This review summarizes recent advances in fabrication techniques and processing parameters for Ag-based coatings, including electroplating, electroless deposition, magnetron sputtering, electrospark deposition, thermal spraying, and electrical explosion spraying on metallic substrates, particularly on copper and steel substrates. More attention is given to microstructural design strategies, such as the incorporation and homogeneous dispersion of reinforcement or solid lubricant phases within the Ag matrix, to enhance contact reliability and operational endurance. The performance of Ag-based coatings is analyzed in terms of their physical, chemical and mechanical properties, electrical contact resistance, friction and wear behavior, arc erosion resistance, and environmental durability under different service conditions. Key challenges, including coating degradation under high electrical loads, mechanical wear, and corrosive environments, are highlighted. Future research directions are outlined, focusing on multifunctional coating structures that enhance surface performance and ensure the long-term durability of electrical contacts.

17 October 2023 in Surface Engineering and Applied Electrochemistry
Verified
Journal Article
Closed access
PDF file
SBS. S. Belevskii
S. S. Belevskii
AGA. V. Gotelyak
A. V. Gotelyak
SISergiu IVASCU
Sergiu IVASCU
KKK. V. Kovalenko
K. V. Kovalenko
ADAlexandr Dikusar
Alexandr Dikusar
This work demonstrates that the macroscopic size effect, which consists in the influence of electrodeposition surface area on the composition and propertie

1 January 2025
Verified
Conference Paper
Closed access
PDF file
VMValentin Mihailov
Valentin Mihailov
NKNatalia Kazak
Natalia Kazak
SISergiu IVASCU
Sergiu IVASCU
AIAnatolie Ianachevici
Anatolie Ianachevici
SISpiridon Iatco
Spiridon Iatco
СЯСпиридон Яцко
Спиридон Яцко
The synthesis of multicomponent and multifunctional coatings in low-voltage discharge plasma using compact electrodes made of graphite, refractory metals such as titanium, tantalum and tungsten, as well as their powders has been studied. Optimised energy regimes (energy value of electric discharges) have been identified at which the most qualitative coatings (uniform and continuous) with the highest content of carbide phases were obtained, which provide high hardness and service life under wear conditions. The utilisation of powders as alloying materials in lieu of compact electrodes has enabled the attainment of significantly thicker coatings and an enhancement in the process's productivity. This will facilitate the expansion of the technology's potential applications.