Hang Jing

Mr. Hang Jing


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
SLShengao Lin
Shengao Lin
JLJing Li
Jing Li
HYHeng Yan
Heng Yan
XMXianfu Meng
Xianfu Meng
XQXiang Qingpei
Xiang Qingpei
CYChuting Yang
Chuting Yang
Bismuth telluride (Bi2Te3)-based alloys have been extensively employed in energy harvesting and refrigeration applications for decades. However, commercially produced Bi2Te3-based alloys using the zone-melting (ZM) technique often encounter challenges such as insufficient mechanical properties and susceptibility to cracking, particularly in n-type Bi2Te3-based alloys, which severely limit the application scenarios for bismuth telluride devices. In this work, we seek to enhance the mechanical properties of n-type Bi2Te2.7Se0.3 alloys while preserving their thermoelectrical performance by a mixed mechanism of grain refinement and the TiN composite phase-introduced pinning effect. These nanoscale processes, coupled with the addition of TiN, result in a reduction in grain size. The pinning effects of nano-TiN contribute to increased resistance to crack propagation. Finally, the TiN-dispersed Bi2Te2.7Se0.3 samples demonstrate increased hardness, bending strength and compressive strength, reaching 0.98 GPa, 36.3 MPa and 74 MPa. When compared to the ZM ingots, those represent increments of 181%, 60% and 67%, respectively. Moreover, the thermoelectric performance of the TiN-dispersed Bi2Te2.7Se0.3 samples is identical to the ZM ingots. The samples exhibit a peak dimensionless figure of merit (ZT) value of 0.957 at 375 K, with an average ZT value of 0.89 within the 325–450 K temperature range. This work has significantly enhanced mechanical properties, increasing the adaptability and reliability of bismuth telluride devices for various applications, and the multi-effect modulation of mechanical properties demonstrated in this study can be applied to other thermoelectric material systems.

5 January 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
LZLiu Zhenghao
Liu Zhenghao
HYHeng Yan
Heng Yan
JLJing Li
Jing Li
XCXiaoxi Chen
Xiaoxi Chen
HJHang Jing
Hang Jing
MMMingyang Ma
Mingyang Ma
Mechanical and thermoelectric performance of a SiGe thermoelectric module were investigated through finite element analysis. N-type and P-type SiGe thermoelectric materials were synthesized, and their mechanical and thermoelectric properties were experimentally measured. Thermal stress distributions within the SiGe module and the integrated “heat collector–module–heat sink” assembly are simulated, and the results were compared with the measured mechanical strength of the SiGe materials. The simulations show that among the three electrode structures evaluated—C/W/C sandwich, 0.5 mm W/C, and 0.1 mm W/C—the C/W/C sandwich configuration yields the lowest thermal stress. An inter-leg spacing of 0.5 mm also leads to reduced stress compared to a 0.1 mm gap. However, fully constraining the cold end or directly integrating the module with heat collection and dissipation components significantly increases thermal stress. The use of copper cooling plates induces higher stress than C-C plates, exceeding the tolerable strength of the materials. Simulation of a module with 28 SiGe legs (each 10 mm × 10 mm × 1.5 mm) predicts an output power of 7.42 W and a conversion efficiency of 7.11% at a hot-side temperature of 967 °C and a cold-side temperature of 412 °C.