Large sized W1/O/W2 double emulsion droplets with uniform wall thickness and diameters were prepared by adopting the emulsion microencapsulation method. Via visually online counting the number of double emulsion droplets over observing time, the stability of these compound droplets solidified in a constant rotating flow field was comprehensively studied. Combining emulsion kinetics, the adsorption radius of polymer chains, surface tension and rheological properties of the outer water phase (W2), the influence of sucrose concentration on the stability of double emulsion droplets was systematically investigated. Combining the change of surface tension, the size of adsorbed polyvinyl alcohol (PVA) chains and storage modulus of the W2 phase, mechanisms of the interactions between sucrose molecules and PVA chains were fully elucidated in this paper. Moreover, the results showed that the stability of the double emulsion droplets was improved when the contents of sucrose was less than 1.0 wt%. This is probably due to the proper match between shear force and surface tension of the W2 phase, and less inward force caused by osmotic pressure in dilute sucrose concentrations.
Bismuth telluride (Bi2Te3)-based alloys have been extensively employed in energy harvesting and refrigeration applications for decades. However, commercially produced Bi2Te3-based alloys using the zone-melting (ZM) technique often encounter challenges such as insufficient mechanical properties and susceptibility to cracking, particularly in n-type Bi2Te3-based alloys, which severely limit the application scenarios for bismuth telluride devices. In this work, we seek to enhance the mechanical properties of n-type Bi2Te2.7Se0.3 alloys while preserving their thermoelectrical performance by a mixed mechanism of grain refinement and the TiN composite phase-introduced pinning effect. These nanoscale processes, coupled with the addition of TiN, result in a reduction in grain size. The pinning effects of nano-TiN contribute to increased resistance to crack propagation. Finally, the TiN-dispersed Bi2Te2.7Se0.3 samples demonstrate increased hardness, bending strength and compressive strength, reaching 0.98 GPa, 36.3 MPa and 74 MPa. When compared to the ZM ingots, those represent increments of 181%, 60% and 67%, respectively. Moreover, the thermoelectric performance of the TiN-dispersed Bi2Te2.7Se0.3 samples is identical to the ZM ingots. The samples exhibit a peak dimensionless figure of merit (ZT) value of 0.957 at 375 K, with an average ZT value of 0.89 within the 325–450 K temperature range. This work has significantly enhanced mechanical properties, increasing the adaptability and reliability of bismuth telluride devices for various applications, and the multi-effect modulation of mechanical properties demonstrated in this study can be applied to other thermoelectric material systems.
1 September 2020 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
Mechanical and thermoelectric performance of a SiGe thermoelectric module were investigated through finite element analysis. N-type and P-type SiGe thermoelectric materials were synthesized, and their mechanical and thermoelectric properties were experimentally measured. Thermal stress distributions within the SiGe module and the integrated “heat collector–module–heat sink” assembly are simulated, and the results were compared with the measured mechanical strength of the SiGe materials. The simulations show that among the three electrode structures evaluated—C/W/C sandwich, 0.5 mm W/C, and 0.1 mm W/C—the C/W/C sandwich configuration yields the lowest thermal stress. An inter-leg spacing of 0.5 mm also leads to reduced stress compared to a 0.1 mm gap. However, fully constraining the cold end or directly integrating the module with heat collection and dissipation components significantly increases thermal stress. The use of copper cooling plates induces higher stress than C-C plates, exceeding the tolerable strength of the materials. Simulation of a module with 28 SiGe legs (each 10 mm × 10 mm × 1.5 mm) predicts an output power of 7.42 W and a conversion efficiency of 7.11% at a hot-side temperature of 967 °C and a cold-side temperature of 412 °C.