The multi-material injector casting (MMIC) process allows the production of castings with two different alloys in a single process. The metal is introduced into the mold through a ceramic down sprue (injector) that moves with the rising surface of the melt. This results in a beneficial temperature distribution in the casting with enhanced filling and feeding properties. Combining two alloys in one casting affects the chemical composition, microstructure, and mechanical properties, which differ from those of the original alloys. The main goal of producing the dual-alloy castings is to adapt the alloy locally in the mixing zone according to the application needs. The original composition and characteristics of both alloys have to be ensured as much as possible. This article discusses the peculiarities of dual-alloy sand mold casting, considering the oxidation processes of the components under different conditions and the microstructure of the resulting ingots. The results of thermodynamic simulation, experimental dual-alloy sand mold casting, chemical composition, and macrostructure of the resulting castings are given in the article. The following factors have been investigated: the method of pouring two alloys (AlSi12 and AlSi9Cu3), which simulate two injector positions; the time between pouring each alloy (60, 90, and 120 s); the influence of a directional solidification with the bottom chill. The mixing zone was identified by the changes in the content of Cu measured by spark spectroscopy and EDS.
22 November 2025 in International Journal of Metalcasting
In the multi-material injector casting process, two different melts are cast consecutively into a mold through a ceramic injector. The current work comprises the manufacturing and characterization of Al/Al double-alloy castings using this novel process. The experimental setup is described, and castings consisting of EN AC-AlSi9Cu3(Fe) and EN AC-AlSi12(a) are fabricated. The influence of the time interval between casting both alloys on the mixing behavior and mechanical properties is investigated. Optical inspection and spark spectrometry testing showed the realization of multi-material components characterized by a vertical material gradient. The transition zone is investigated by tensile and torsion tests. In both experiments, the specimens failed predominantly in the weaker material, AlSi12. An early failure of the cohesive transition zone is not detected. The utilization of a digital image correlation system reveals a locally varying deformation behavior of the specimens during the tensile experiments.
Angesichts steigender Energiekosten sowie eines zunehmenden Bewusstseins für nachhaltige Produktion ist es heute erforderlich, Zielvorgaben für den Energieverbrauch in der Produktionsplanung und -steuerung zu verankern sowie umzusetzen. Aus diesem Grund präsentiert dieser Artikel ein Verfahren für eine energieorientierte Produktionssteuerung, die auf der Basis von Energieflexibilität und Lastmanagement den Energiebedarf der Produktion mit einem begrenzten Energieangebot synchronisiert. Due to rising energy costs and a growing awareness for sustainable production, it is now necessary for companies to establish targets for energy consumption in production planning and control. Therefore, this article illustrates a method for energy-oriented production control on the basis of flexibility and load management which synchronizes the energy demand in manufacturing with a limited energy supply.
As global markets increasingly demand sustainability and circular economy concepts are on the rise, products have to change as well. In this state of research paper, we discuss effects of circular economy concepts on production. Our research consists of four pillars. Due to circular economy, products or their components will be more often brought to a second life and thus their design should be more modular to allow efficientcomposing and decomposing. Second, the flexibility of production needs to increase to allow for the integration of dis- and reassembly steps. As a basis, we discuss how circular production layouts will change as products and components are reintegrated into production. Thirdly, this increase in complexity requires more elaborate information systems support. We discuss requirements and we present a software-based optimization approach for production layout planning. Fourth, IT platforms enable new ways to reach customers and more flexible business models. Thus, traditional production companies can innovate and transform towards providing industrial goods services. Finally, we present how we want to illustrate our intended research based on a model factory.
The increasing demand for components with tailored properties and functionally graded materials featuring adjustable interfaces is raising the requirements in gravity sand and die casting processes of aluminium. In response to these challenges, a novel controlled process based on injector casting is being developed. This innovative process involves the sequential pouring of two liquid aluminium alloys into a mould while mixing the two liquid phases. By adjusting the injector outlet, the process aims to achieve a horizontal flow deflection. This study systematically investigates two variations of horizontal deflections at the injector outlet and examines their impacts on flow volume rate, flow velocity, and the flow channel at the injector outlet in relation to their impact on the mixing characteristics. These variations are analysed through water model experiments. The findings from these water model experiments are critically evaluated to assess their applicability to the aluminium casting process. Based on these evaluations, conclusions are drawn to improve the design of an application-specific injector for a multi-material injector casting process (MMIC). The results offer valuable insights into optimising the manufacturing process to achieve the desired material properties and gradient configurations.