Weather radar is an active remote sensing device used to monitor the full lifecycle changes in severe convective weather with high spatial and temporal resolution. Effective radar calibration is a crucial foundation for ensuring the high-quality application of observational data. This paper utilizes a UAV platform equipped with a high-precision RTK system and standard metal spheres to study the principles and methods of metal sphere calibration, constructing a complete calibration process and calibration accuracy evaluation metrics. Additionally, a collocated radar comparison observation experiment was conducted for cross-validation, and metal sphere calibration tests were performed on problematic radars. The experimental results indicate the following: (1) The combined application of a high-precision RTK system and a laser range camera can provide real-time position information on the metal sphere, improving the efficiency of radar target acquisition. (2) The calibration method based on UAV-suspended metal spheres can periodically conduct the quantitative calibration of Z and ZDR, achieving calibration accuracies within 0.5 dB and 0.2 dB, respectively, and supports the qualitative inspection of key parameters such as beamwidth and pulse width. (3) During field tests, a high success rate “coarse adjustment + fine adjustment + staring” sphere-finding technique was established, based on automatic switching between RHI, PPI, and FIX scanning modes. This method directs the UAV to adjust the metal sphere to the center of the radar distance bin, reducing the impact of uneven beam filling and bin crossing, ensuring the accuracy of scattering characteristic measurements.
To better calibrate the aerosol lidar network constructed by the China Meteorological Administration, and ensure the data quality observed by the network, the Meteorological Observation Center (China Meteorological Administration) and the University of Naples (Italy) jointly developed a “high quality 532 nm Raman aerosol lidar” (REAL lidar) in 2018. The ability to detect Raman–Mie scattering signals was improved through signal detection in a large dynamic range. This study compared the REAL lidar with the reference lidar (European ACTRIS aerosol lidar network) considering three wavelengths and eight channels. The results show that both the original signals and data products of the two radars exhibited good consistency. In the calibration application of China’s domestic lidar network, after REAL calibration, the relative average and standard deviations of the backscattering coefficient of the in-station lidar decreased from 55.4% to 7.9% and from 64% to 9.9%, respectively. The effect was significant, which indicates that REAL is an aerosol lidar with a high-performance index. The results satisfy the demand for calibration of the aerosol lidar network, and the REAL was successfully applied to the calibration of the aerosol lidar network.
The quality of weather radar affects the reliability and effectiveness of monitoring severe convective weather. Therefore, rigorous calibration and validation are the foundation for the quantitative application of weather radar. Among the available methods, radial velocity validation is of great significance for reducing the false alarm rate in the identification of tornadoes and thunderstorms. Based on the traditional method that utilizes internal and external instrument radar velocity measurements, we propose a weather radar radial velocity validation method that uses RTK UAV to simulate external targets. In addition, according to the characteristics of the UAV application scenarios, we introduce the evaluation parameter of optimal absolute accuracy to supplement the original parametric system. The experimental results show that the evaluation parameter of optimal absolute accuracy can effectively reduce the interference caused by the systematic deviation of the UAV due to the internal and external environment, which can affect the validation results. When the UAV velocity is not greater than 10 m/s, the optimal absolute accuracy of the radial velocity validation is less than 0.05 m/s, which is essentially consistent with the external instruments’ measurement results. This method can be effectively applied to the procedural handling of weather radar radial velocity validation. It is significant for ensuring the accuracy and quality of weather radar radial velocity measurements and improving the effectiveness of radar velocity data applications.
Parameter estimation is important in weather radar signal processing. Time-domain processing (TDP) and frequency-domain processing (FDP) are two basic parameter estimation methods used in the weather radar field. TDP is widely used in operational weather radars because of its high efficiency and robustness; however, it must be assumed that the received signal has a symmetrical or Gaussian power spectrum, which limits its performance. FDP does not require assumptions about its power spectrum model and has a seamless connection to spectrum analysis; however, its application performance has not been fully validated to ensure its robustness in an operational environment. In this study, we introduce several technical details in FDP, including window function selection, aliasing correction, and noise correction. Additionally, we evaluate the performance of FDP and compare the performance of FDP and TDP based on simulated and measured weather in-phase/quadrature (I/Q) data. The results show that FDP has potential for operational applications; however, further improvements are required, e.g., windowing processing for signals mixed with severe clutter.
Tornadoes pose severe threats, yet their low frequency in China creates a labeled data scarcity that hinders training robust detection models. Leveraging abundant U.S. data offers a solution, though cross-domain generalization remains challenging due to distinct climatic environments and heterogeneous radar systems. This study systematically evaluates the generalization capability of three representative models—TORP, TORP-XGB, and TDA-CNN—trained on the U.S. TorNet dataset and applied to Chinese CINRAD observations (2020–2024) via a zero-shot transfer strategy. The results indicate that while all models demonstrated robust performance in the source domain (with POD values of 0.75, 0.72, and 0.71 for TORP, TORP-XGB, and TDA-CNN, respectively), they experienced varying degrees of performance attenuation in the target domain (with POD values dropping to 0.56, 0.48, and 0.41, respectively). Notably, the TORP model exhibited superior robustness with minimal performance degradation. Further analysis primarily attributes this cross-domain degradation to three factors: disparities in radar systems, magnitude differences in tornado rotational features, and data quality issues. Crucially, sensitivity experiments confirm that linear feature enhancement substantially improves the detection rate and effectively mitigates the cross-domain performance gap, albeit at the cost of increased false alarms. These findings provide a reference for the cross-domain deployment of tornado identification models and future improvements in transfer learning strategies.
In response to the urgent need for calibration technology in the application of wind lidar in the meteorological operations, this paper describes the development of a Reference-type Coherent Doppler Wind Lidar(RCDWL) for calibration. Based on a dual-channel composite detection mechanism combining continuous and pulsed modes, the RCDWL achieves key technical specifications including a low blind zone of 10 m, a high resolution of 10 m, and a maximum detection altitude of 3,000 m. To verify the performance and stability of the RCDWL, comparison experiments and data analyses were conducted using a radiosonde and a meteorological gradient tower, respectively. Comparison results with the radiosonde showed a wind speed systematic error of -0.05 m/s and a standard deviation of 1.11 m/s, while the wind direction systematic error was 1.34° with a standard deviation of 12.05°; the correlation coefficients were all higher than 0.97.Comparison results with the gradient tower showed a systematic error of 0.01 m/s and a standard deviation of 0.28 m/s for wind speed, and a systematic error of -0.09° and a standard deviation of 2.90° for wind direction, with correlation coefficients all exceeding 0.98. Based on these results, we used RCDWL as a reference source for a joint comparison and analysis of 9 lidars in meteorological operations. The results showed that the correlation coefficients for horizontal wind speed were greater than 0.98, with standard deviations less than 0.8 m/s; for wind direction, the correlation coefficients were greater than 0.97, with standard deviations less than 8°. Additionally, when using RCDWL as a reference standard source for the comparison and calibration of lidars prior to shipment, RCDWL effectively improves the product accuracy of lidars prior to shipment. These results fully validate the detection capabilities and stability of the RCDWL, establishing a stable and reliable reference benchmark for lidar calibration within the meteorological operations. The RCDWL fills a technical gap in wind lidar calibration reference sources and can be used for the comparison and calibration of Lidar equipment, holding great practical significance for enhancing the application level of wind lidars in various fields.