Omid Emadinia

Dr. Omid Emadinia

Department of Metallurgical and Materials Engineering, Faculty of Engineering University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto, Portugal
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
HNHelder Nunes
Helder Nunes
Omid EmadiniaOmid Emadinia
Omid Emadinia
RSRui Soares
Rui Soares
Manuel VieiraManuel Vieira
Manuel Vieira
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
Aluminum is a critical element of the circular economy as it can be recycled several times. Moreover, Al recycling is a more economically and environmentally efficient procedure than the primary Al production from ores. Secondary aluminum alloys are mostly used in casting applications since it is possible to accommodate their chemical composition through secondary manufacturing processes. However, the quality of the alloys may be considerably altered during the different steps of the recycling process. Inadequate waste sorting might result in excessive contamination. Iron is the most dangerous contaminant because it causes brittle and fragile intermetallic phases, which significantly impacts the mechanical characteristics of alloys. In addition, the microstructure of the alloy changes significantly after multiple cycles of remelting. These issues lead to the downcycling of aluminum, i.e., in other words, the reduction in the overall quality of the alloys. Thus, it has been shown that a number of procedures, including ultrasonic melt treatment and microalloying with rare earths, can somewhat alter the shape of the Fe-rich phases in order to reduce the shortcomings of downcycling. However, a solid mechanical characterization is still missing in order to improve the Fe-rich phase alteration.

17 April 2023 in Metals
Verified
Journal Article
Open access
PDF file
FZFahad Zafar
Fahad Zafar
Omid EmadiniaOmid Emadinia
Omid Emadinia
JCJoão Castro Conceição
João Castro Conceição
Manuel VieiraManuel Vieira
Manuel Vieira
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
The direct laser deposition (DLD) process has seen rigorous research in the past two decades due to its ability to directly manufacture products followed by minimal machining. The process input variables play a vital role in determining the properties achieved in the products manufactured by the DLD method. Inconel 625, a nickel-based superalloy with exceptional mechanical performance and corrosion resistance, has been used in critical applications within the aerospace, process, and marine industry. However, its poor machinability and higher load requirements for plastic deformation have been challenging for manufacturers. Therefore, many studies have explored the additive manufacturing of Inconel 625 to overcome these problems. This article focuses on the DLD of Inconel 625 and its composites, presenting the state-of-the-art, drawing a relation among laser processing parameters and resulting material properties, microstructure and phase evolution, and the high-temperature performance of DLD Inconel 625. The paper highlights the areas on which further studies may focus.

20 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
CBCatarina Batista
Catarina Batista
AFAdriana André Martins das Neves de Pinho Fernandes
Adriana André Martins das Neves de Pinho Fernandes
TVTeresa Vieira
Teresa Vieira
Omid EmadiniaOmid Emadinia
Omid Emadinia
Chips are obtained by subtractive processes such as machining workpieces and until recently considered as waste. However, in recent years they are shown to have great potential as sustainable raw materials for powder technologies. Powder production from metal chips, through the application of solid-state processes, seems to be an alternative to conventional atomization from liquid cooled with different fluids. However, chip material and processing have an essential role in the characteristics of powder particles, such as particle size, shape, size distribution and structure (4S’s), which are essential parameters that must be considered having in mind the powder process and the metallurgy applications. Moreover, different approaches refereed in the application of this new “powder process” are highlighted. The goal is to show how the actual research has been transforming subtractive processes from a contributor of wastes to clean technologies.

26 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
AFAndré Alves Ferreira
André Alves Ferreira
Omid EmadiniaOmid Emadinia
Omid Emadinia
JCJoão Manuel Cruz
João Manuel Cruz
Ana Rosanete ReisAna Rosanete Reis
Ana Rosanete Reis
Manuel VieiraManuel Vieira
Manuel Vieira
Functionally graded material (FGM) based on Inconel 625 and AISI 431 stainless steel powders was produced by applying the direct laser deposition (DLD) process. The FGM starts with layers of Inconel 625 and ends with layers of 431 stainless steel having three intermediate zones with the composition (100-X)% Inconel 625-X% 431 stainless steel, X = 25, 50, and 75, in that order. This FGM was deposited on a 42CrMo4 steel substrate, with and without preheating. Microstructures of these FGMs were evaluated, while considering the distribution of chemical composition and grain structure. Microstructures mainly consisted of columnar grains independent of preheating condition; epitaxial growth was observed. The application of a non-preheated substrate caused the formation of planar grains in the vicinity of the substrate. In addition, hardness maps were produced. The hardness distribution across these FGMs confirmed a smooth transition between deposited layers; however, the heat-affected zone was greatly influenced by the preheating condition. This study suggests that an optimum Inconel 625/AISI 431 FGM obtained by DLD should not exceed 50% AISI 431 stainless steel.

19 March 2020 in Metals
Verified
Journal Article
Open access
PDF file
Elsa W. SequeirosElsa W. Sequeiros
Elsa W. Sequeiros
Omid EmadiniaOmid Emadinia
Omid Emadinia
TVTeresa Vieira
Teresa Vieira
Manuel VieiraManuel Vieira
Manuel Vieira
Hot embossing is a small-scale, low-cost processing technology that can deliver products to the market in a short time. This microreplication technology is well established to produce polymeric components and has applications in several industrial sectors. The use of micropowder hot embossing in the production of metal components is an emerging and challenging process that, when compared to other typical technologies, brings some economic advantages in a volatile market with an increasing tendency to manufacture customized products. The main objective of this review is to analyze the potential of powder hot embossing and its developments in the production of metallic microparts/components. This technology requires four distinct steps: (1) production feedstock (preparation of mixtures), (2) hot embossing (shape forming), (3) debinding and (4) sintering. These steps are interrelated and influence the characteristics of the final metallic microparts. This study summarizes the approaches implemented for the use of different metallic powders and polymeric binder systems for the preparation of the feedstock, the mold materials and the critical conditions tested in the embossing step to produce green parts, and the production of the final parts through the application of debinding and sintering. Powder hot embossing is a viable replication technology that allows the production of new metallic microcomponents, contributing to the global scientific effort of miniaturizing manufacturing process, equipment and products. The merit of powder hot embossing for industrialization needs further development to assert itself in the market and compete with other micromanufacturing techniques.

24 August 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
Sónia SimõesSónia Simões
Sónia Simões
Ana Sofia RamosAna Sofia Ramos
Ana Sofia Ramos
Filomena VianaFilomena Viana
Filomena Viana
Omid EmadiniaOmid Emadinia
Omid Emadinia
TVTeresa Vieira
Teresa Vieira
Manuel VieiraManuel Vieira
Manuel Vieira