Low-density cancellous bone results in reduced trabecular support and may increase crestal cortical strain around implants. Osseodensification (OD) compacts trabecular bone and may create a peri-osteotomy densified zone, but its strain-level effects in osteoporotic-like bone are unclear. This study evaluated whether an OD-inspired peri-implant densified trabecular zone reduces crestal cortical strain compared with conventional drilling (CD) in an osteoporotic-like model. A three-dimensional finite element model of a mandibular posterior segment with a 2.0-mm cortical shell and D4 cancellous core was constructed with a 4.3 × 11.4-mm titanium implant and a cemented monolithic zirconia crown. CD used a 4.0-mm osteotomy in D4 bone. The OD model used the same osteotomy plus a concentric peri-implant densified shell with radial density gradation from D1 to D3. The implant–bone interface was defined as bonded. Static 100 N axial and 45° oblique loads were applied. Outcomes were εeq, εmax, and εmin, summarized as mean top-10 nodal values. OD reduced crestal cortical strains under both loads. Under axial loading, εeq, εmax, and |εmin| decreased by 17.7%, 19.0%, and 24.1%, respectively. Under oblique loading, the corresponding reductions were 9.8%, 8.0%, and 8.9%. Oblique loading produced higher cortical strains than axial loading in both models. OD-inspired peri-implant densification reduced crestal cortical strain in this osteoporotic-like model, whereas oblique loading remained the main driver of elevated strain. These findings support occlusal/prosthetic strategies that minimize oblique forces and warrant experimental and clinical validation.
Background/Objectives: Low-density cancellous bone can amplify crestal cortical strain around implants because trabecular support is reduced. Osseodensification (OD) compacts trabecular bone and may create a peri-osteotomy densified zone, but its strain-level effects in osteoporotic-like bone are unclear. Given that osteoporosis/osteopenia in aging populations reduce trabecular support and can increase crestal cortical loading, this study tested whether an OD-inspired peri-implant densified trabecular zone lowers high-tail crestal cortical strains versus conventional drilling in an osteoporotic-like cancellous model. Materials and Methods: A 3D finite element mandibular posterior segment (2.0-mm cortical shell and D4 cancellous core) was modeled with a 4.3×11.4-mm titanium implant and a cemented monolithic zirconia crown. CD used a 4.0-mm osteotomy in D4 bone. OD used the same osteotomy plus an axially varying concentric densified shell (D1→D3 radially) with minor buccolingual cortical expansion. The implant–bone interface was bonded. Static 100 N loads were applied axially and obliquely (45°). Outcomes were εeq, εmax, and εmin, summarized as mean top-10 nodal values. Results: OD reduced crestal cortical strains under both loads. Axial loading: εeq 1470→1210 µε (−17.7%), εmax 1420→1150 µε (−19.0%), |εmin| 900→683 µε (−24.1%). Oblique loading: εeq 3370→3040 µε (−9.8%), εmax 2510→2310 µε (−8.0%), |εmin| 3040→2770 µε (−8.9%). Oblique loading produced higher cortical strains than axial loading in both models. Conclusions: OD-inspired peri-implant densification attenuated high-tail crestal cortical strain demand in this osteoporotic-like model, whereas off-axis loading remained the dominant driver of elevated strain. These findings support occlusal/prosthetic strategies that minimize oblique forces and warrant experimental and clinical validation.
11 July 2025 in Odovtos - International Journal of Dental Sciences
Training in dental carving has played an important role in the education of dental students by developing their manual skills and preparing them for other areas of knowledge that require these skills. This study aimed to evaluate students' performance with different carving materials used in dental anatomy courses and their opinions on these materials. 124 first-year preclinical students participated in this study. They prepared cube blocks of plaster, wax, and soap. From each block they carved a sphere of 2 cm diameter. They were given one hour for each material. At the end of the period, the works were collected. After the carving was completed, a 5-question survey was given to the students to find out their thoughts. The works were graded by three prosthodontists. The grades were compared statistically and the students' opinions were evaluated. The wax work had the highest mean, and this difference was significant. The mean of the plaster work was the lowest. These marks were directly proportional to the students' thoughts. Most of the students wanted the carving material used in the courses to be wax, and a few of them wanted it to be plaster. The students liked working with wax the most and performed best when working with wax. They found the plaster carving the most difficult and performed the worst.
12 March 2026 in Journal of Health Sciences and Medicine
Aims: Three-dimensional (3D) printing of zirconia is an emerging domain in digital dentistry; however, its global research landscape, collaboration structure, and thematic focus have not been comprehensively mapped. The aim of this study was to characterize scientific output, collaboration patterns, citation impact, and major research themes in publications on 3D-printed zirconia in dentistry.Methods: A Web of Science Core Collection (WoS-CC) Topic Search was conducted in December 2025 using terms related to zirconia, additive manufacturing/3D printing, and dental applications. Of 584 retrieved records, 185 eligible articles on 3D-printed zirconia for dental use (2009–2025) were included. Descriptive indicators were calculated (annual production, journals, countries, institutions, authors, and citations). Co-authorship and keyword co-occurrence networks were generated with VOSviewer to visualize collaboration and identify thematic clusters.Results: Publication activity increased sharply after 2019, with 128/185 publications (69.2%) published in 2023–2025. Most documents were original research articles (n=159) or reviews (n=26); no case reports were identified in WoS-CC. The 185 articles involved 730 authors from 38 countries and were published in 48 journals. China and the United States were leading contributors. Network analyses identified three interconnected themes: digital/additive manufacturing workflows, implantprosthodontic applications, and biomechanical or accuracy-based evaluation. Evidence was predominantly in vitro and laboratory-based, with limited clinical data.Conclusion: Research on 3D-printed zirconia in dentistry is rapidly expanding but concentrated in a small set of countries, institutions, and journals. Future studies should prioritize clinical investigations and standardized reporting of printing and post-processing parameters to support translation into predictable outcomes.
1 July 2025 in International Journal of Adhesion and Adhesives