With the rapid development of software-defined radio (SDR) technology, a digital, software-reconfigurable, and flexible solution is provided for microwave radiometers, particularly suitable for atmospheric water vapor and oxygen detection with wideband, multi-channel requirements, significantly improving system efficiency. Meanwhile, digitization helps improve channel consistency and address nonlinearity issues, while the digital zero-balancing mechanism implemented through adaptive integration is more suitable for digital platforms. This paper proposes a digital Dicke-type radiometer system based on an SDR platform, using Xilinx RFSoC XCZU47DR as the core hardware to achieve single-chip integration of RF signal sampling, digital local oscillator generation, and signal processing. The system implements a 46-channel channelized receiver (23 channels each for K-band and V-band) on FPGA using a polyphase filter bank. The prototype filters achieve 70 dB stopband attenuation and 0.5 dB passband ripple, with each polyphase branch requiring only 25 coefficients, significantly reducing hardware resource consumption. An adaptive integration method is proposed, where an adaptive switch controller dynamically adjusts the hot source injection time ratio by calculating the power difference between adjacent integration periods, enabling the Dicke zero-balancing mechanism to operate entirely in the digital domain. Furthermore, a complete hardware transfer model is established for three signal branches (antenna, hot source, and matched load), and full-chain calibration of all 46 channels is performed using a liquid nitrogen cold source, with calibration reliability verified through blackbody measurements. Experimental results demonstrate that the system achieves better than 0.7 K brightness temperature consistency across channels, with sensitivity less than 0.15 K at 1-s integration time, confirming its excellent channel consistency and measurement stability.

With the rapid development of software-defined radio (SDR) technology, a digital, software-reconfigurable, and flexible solution is provided for microwave radiometers, particularly suitable for atmospheric water vapor and oxygen detection with wideband, multi-channel requirements, significantly improving system efficiency. Meanwhile, digitization helps improve channel consistency and address nonlinearity issues, while the digital zero-balancing mechanism implemented through adaptive integration is more suitable for digital platforms. This paper proposes a digital Dicke-type radiometer system based on an SDR platform, using Xilinx RFSoC XCZU47DR (AMD, San Jose, CA, USA) as the core hardware to achieve single-chip integration of RF signal sampling, digital local oscillator generation, and signal processing. The system implements a 46-channel channelized receiver (23 channels each for K-band and V-band) on an FPGA using a polyphase filter bank. The prototype filters achieve 70 dB stopband attenuation and 0.5 dB passband ripple, with each polyphase branch requiring only 25 coefficients, significantly reducing hardware resource consumption. An adaptive integration method is proposed, where an adaptive switch controller dynamically adjusts the hot source injection time ratio by calculating the power difference between adjacent integration periods, enabling the Dicke zero-balancing mechanism to operate entirely in the digital domain. Furthermore, a complete hardware transfer model is established for three signal branches (antenna, hot source, and matched load), and full-chain calibration of all 46 channels is performed using a liquid nitrogen cold source, with calibration reliability verified through blackbody measurements. Experimental results demonstrate brightness temperature consistency better than 0.7 K, with a sensitivity of less than 0.15 K for the K-band and less than 0.21 K for the V-band at 1 s integration time.

In this paper, a matching method for altimeter and transponder signals in Sub-optimal Maximum Likelihood Estimate (SMLE) tracking mode is proposed. In the in-orbit calibration of the altimeter in SMLE tracking mode using the reconstructive transponder, it is necessary to separate the forwarding signal from the ground echo signal. At the same time, the fluctuations in the received signal of the altimeter, which are caused by the forwarding signal of the transponder, can be eliminated. The transponder generates a bias when measuring the arrival time of the transmitting signal from the altimeter and embeds this bias in both the transponder-recorded data and the altimeter-recorded data. Therefore, the two sets of data have one-to-one correspondence, and they are superimposed using the sliding sum method. Moreover, the distance between the altimeter and the transponder is a parabolic geometric relationship, and the outliers are eliminated by the fitting error minimization decision, and the transponder signal is separated from the ground echo. The final altimeter transmitting–receiving signal path is obtained. Furthermore, the principles underlying this method can be used for any transponder that can adjust the response signal delay during calibration.

Ground-based scatterometers are widely used for quantitative microwave backscattering measurements in soil moisture retrieval, vegetation monitoring, and satellite scatterometer validation. However, low-cost software-defined radio (SDR) transceivers provide limited instantaneous bandwidth, making it difficult to transmit and process signals with bandwidths on the order of hundreds of MHz for fine range resolution, especially for systems requiring real-time onboard processing. To address this problem, this paper presents a vehicular, fully polarimetric, SDR-based scatterometer that achieves an equivalent wideband response by sequentially transmitting adjacent narrow subbands and coherently synthesizing them onboard. To enable real-time operation on a resource-limited field-programmable gate array/system-on-chip (FPGA/SoC) platform, we adopt a frequency-domain synthesis-pulse-compression pipeline that avoids interpolation and eliminates repeated matched filtering across subbands. A slot-based online phase calibration is performed within the settling window after each fast lock to estimate and compensate random local oscillator (LO) phase offsets, preserving coherent stitching. In addition, pulse repetition within each subband and coherent accumulation are integrated to improve the signal-to-noise ratio (SNR) under real-time throughput constraints. A Zynq-based implementation demonstrates deterministic onboard range-profile output, with a minimum processing latency of about 1.57 ms per frame. Loopback and outdoor experiments validate the equivalent 200 MHz bandwidth (five 40 MHz subbands), achieving approximately 0.75 m resolution and yielding sidelobe metrics consistent with the designed windowing, including a peak sidelobe ratio (PSLR) of −27.43 dB and an integrated sidelobe ratio (ISLR) of −12.38 dB. Field scans over farmland further show consistent ${\mathsf{\sigma }}_0$ trends across incidence angle and azimuth, indicating reliable onboard quantitative backscattering measurement. These results demonstrate that the proposed method provides a feasible solution for deterministic real-time equivalent wideband scatterometry on a low-cost SDR platform.