Dmytro Vyktorovych Ivanchenko

Dr. Dmytro Vyktorovych Ivanchenko

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2023 in Casting Processes
Verified
Journal Article
Closed access
NINational Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
Dmytro Vyktorovych IvanchenkoDmytro Vyktorovych Ivanchenko
Dmytro Vyktorovych Ivanchenko
MYMykhail Михайлович Yamshinskij
Mykhail Михайлович Yamshinskij
The paper considers the important features of the technology of strengthening AK7ch aluminum alloy with zirconium introduced with its tetrafluoride. The choice of a complex flux containing zirconium tetrafluoride in its composition is justified. It is indicated that in order to recover zirconium from its tetrafluoride in the aluminum melt, it is first of all necessary to ensure the formation of sodium or potassium fluorozirconate in the strengthening mixture. The mechanism of recovery of zirconium from tetrafluoride is presented. Technological recommendations for obtaining AK7ch alloy are given. It has been established that the complex flux intended to the alloy, which is modified, must be injected into liquid aluminum before the introduction of other alloying elements, namely silicon and magnesium. The maximum appropriate temperature for injecting zirconium into the aluminum melt from the complex flux is indicated. The maximum amount of zirconium that was recovered is 0.4%. The microstructure and mechanical properties of an alloy strengthened by zirconium from its tetrafluoride, which was injected into the alloy in the amount from 0.8 to 1.2%, were studied. As a result of the modification of aluminum alloy AK7ch with zirconium, the grains of silicon solution in aluminum (α-phase) are grind. No other structural changes are observed. The value of tensile strength and relative elongation of the alloy increases by 1.3 and 1.7 times, respectively.

5 June 2024 in Casting Processes
Verified
Journal Article
Open access
Dmytro Vyktorovych IvanchenkoDmytro Vyktorovych Ivanchenko
Dmytro Vyktorovych Ivanchenko
MYMykhail Михайлович Yamshinskij
Mykhail Михайлович Yamshinskij
The paper substantiates that the use of zirconium compounds, namely zirconium dioxide and zirconium tetrafluoride, for the introduction of zirconium into aluminum is relevant, as it allows saturating aluminum-based alloys with zirconium from its intermediate products, namely ZrF4 or ZrO2. The article points out the disadvantages of saturating aluminum with zirconium from the ligature. The use of ZrF4 or ZrO2 as zirconium donors eliminates the need to obtain technically pure zirconium and ligatures from it. The results of thermodynamic calculations of the reduction of zirconium from zirconium tetrafluoride by aluminum are presented. It is established that the reduction of zirconium to Al3Zr is thermodynamically more likely. A flux composition containing zirconium tetrafluoride as a zirconium donor was developed for saturation of aluminum and alloys based on it with zirconium. The composition of the flux was selected based on the analysis of the ZrF4 - LiF state diagram, where the ratio of components was to ensure the lowest possible melting point of the mixture to increase its reactivity. The mechanism of zirconium reduction from tetrafluoride was established, according to which the presence of ternary compounds, in particular Li2ZrF6 or Li3ZrF7, which interact with aluminum, is mandatory in the flux, resulting in the formation of particles of the intermetallic compound Al3Zr. It was found that the zirconium content in the fluxes decreased from 96 % to 34 % 15 minutes after application to the metal surface. The recovered zirconium was transferred to the aluminum solution. The amount of zirconium tetrafluoride that should be introduced into aluminum or alloys based on it to ensure its typical content in the alloys, which, according to DSTU, is 0.2 % for AMg6l, AMg6lch, AMg10, and AMg10ch grades, was calculated. The change in the macrostructure of A7 aluminum after the introduction of zirconium from its tetrafluoride in the flux was studied. The saturation of A7 aluminum with zirconium from the flux grinds the zirconium solution in aluminum and forms a non-dendrite structure. У роботі обґрунтовано твердження про те, що використання сполук цирконію, а саме діоксиду й тетрафториду цирконію, для введення цирконію в алюміній є актуальним, оскільки дозволяє насичувати сплави на основі алюмінію цирконієм із проміжних продуктів його отримання, а саме з ZrF4 або ZrO2. Указано на недоліки насичення цирконієм алюмінію з лігатури. Використання ZrF4 або ZrO2 як донорів цирконію дозволяє позбутися необхідності отримання технічно чистого цирконію та лігатур із нього. Представлено результати термодинамічних розрахунків відновлення цирконію з тетрафториду цирконію алюмінієм. Встановлено, що термодинамічно більш імовірним є відновлення цирконію саме до сполуки Al3Zr. Розроблено склад флюсу, що вміщує тетрафторид цирконію як донор цирконію, призначений для насичення цирконієм алюмінію та сплавів на його основі. Склад флюсу вибирався на основі аналізу діаграми стану ZrF4 – LiF, де співвідношення компонентів мало забезпечити якомога меншу температуру плавлення суміші для підвищення її реакційної здатності. Встановлено механізм відновлення цирконію з тетрафториду, за яким у складі флюсу обов’язковою є наявність потрійних сполук, зокрема Li2ZrF6 або Li3ZrF7, які взаємодіють з алюмінієм, у результаті чого утворюються частки інтерметалідної сполуки Al3Zr. Встановлено, що вміст цирконію у флюсах через 15 хв після нанесення на поверхню металу знижувався з 96 % до 34 %. Цирконій, який відновився, переходив у алюмінієвий розчин. Розраховано кількість тетрафториду цирконію, яку потрібно вводити в алюміній або сплави на його основі з метою забезпечення типового його вмісту у сплавах, який, згідно з ДСТУ, складає 0,2 % для марок АМг6л, АМг6лч, АМг10, АМг10ч. Досліджено зміну макроструктури алюмінію марки А7 після введення цирконію з його тетрафториду у складі флюсу. Насичення алюмінію марки А7 цирконієм із флюсу подрібнює розчин цирконію в алюмінії та формує бездендритну структуру.

30 October 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
APAnatolii Poliakov
Anatolii Poliakov
VVVadym Volokh
Vadym Volokh
AAAndrey Andreev
Andrey Andreev
VRVictor Rebenko
Victor Rebenko
VKViacheslav Kurlov
Viacheslav Kurlov
IKIryna Kovalenko
Iryna Kovalenko
The object of this study is the structural and phase transformations during the carbon reduction of tungsten high-speed steel slag in order to obtain a resource-saving alloying additive. The problem is the loss of precious elements when obtaining and using alloying material from man-made raw materials. Solving the problem is related to the definition of technological parameters to enable the reduction of losses of the corresponding elements. As a result of increasing the degree of scale reduction from 33 % to 72 % and 85 %, the strengthening of the manifestation of the solid solution of carbon and alloying elements in α-Fe relative to FeWO4, FeO and Fe3O4 was revealed. Fe3C, WC, W2C, FeW3C, Fe3W3C, Fe6W6C, VC, V2C, Cr3C2, Cr7C3 and Cr23C6 also appeared. Along with this, rounded and multifaceted particles with different chemical composition and the formation of a spongy microstructure were found. It was established that the most acceptable degree of recovery is 85 %. But achieving a recovery rate of 72 % is also sufficient. This is explained by the fact that the residual carbon in the carbides provides an increased reducing capacity, which is realized during the further reduction of oxides in the liquid metal during alloying. The spongy microstructure results in faster dissolution in contrast to standard ferroalloys, which provides a reduction in melting time while reducing spent resources. No phases with an increased tendency to sublimation were found in the obtained alloying material. That is, no additional conditions are needed that restrain the loss of alloying elements during evaporation with a gaseous phase, which provides an increase in the degree of extraction of the corresponding elements. The properties of the resulting alloying material make it possible to use it in metallurgical production when smelting alloyed steel grades in an electric arc furnace, the composition of which does not have strict restrictions on the carbon content

1 December 2025 in Casting Processes
Verified
Journal Article
Closed access
Dmytro Vyktorovych IvanchenkoDmytro Vyktorovych Ivanchenko
Dmytro Vyktorovych Ivanchenko
MYMykhail Михайлович Yamshinskij
Mykhail Михайлович Yamshinskij
IPIvan Petryk
Ivan Petryk
ILI.V. Lukianenko
I.V. Lukianenko
YCYe.P. Chvertko
Ye.P. Chvertko
IVI. A. Vladymyrskyi
I. A. Vladymyrskyi

31 October 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VVVadym Volokh
Vadym Volokh
APAnatolii Poliakov
Anatolii Poliakov
VRVictor Rebenko
Victor Rebenko
AAAndrey Andreev
Andrey Andreev
MYMykhail Михайлович Yamshinskij
Mykhail Михайлович Yamshinskij
Dmytro Vyktorovych IvanchenkoDmytro Vyktorovych Ivanchenko
Dmytro Vyktorovych Ivanchenko
Peculiarities of phase and structural transformations during the carbon-thermal recovery of high-speed steel slag with the production of an alloying additive were investigated. This is necessary to determine the technological indicators that allow reducing the loss of high-value elements during the production and use of the alloying additive. A gradual change in the degree of scale reduction from 32 % to 69 % and 77 % led to an increase in the appearance of the solid solution of alloying elements and carbon in the α-Fe lattice with respect to FeWO4 and Fe3O4. Along with this, Fe3C, FeW3C, WC, VC, V2C, and Cr3C2 were manifested. At the same time, the formation of polyhedral and rounded particles of different chemical composition and the formation of a spongy microstructure was observed. It was determined that the most acceptable degree of recovery is 77 %. At the same time, the degree of reduction of 69 % is also sufficient since due to the residual carbon in the form of carbides, an increased reduction capacity is ensured with additional reduction of the oxide component in the liquid metal during alloying. The spongy microstructure provides relatively fast dissolution compared to standard ferroalloys, which causes a reduction in the total melting time while reducing the resources spent. No phases and compounds characterized by an increased tendency to sublimation were detected in the obtained alloying additive. That is, there is no need to provide additional conditions that prevent the loss of high-value elements during evaporation with the gas phase, which causes an increase in the degree of extraction of alloying elements. The indicators of the obtained alloying additive make it possible to melt alloyed steel in an electric arc furnace with respect to brands whose composition does not have strict restrictions on carbon, while replacing a part of standard ferroalloys.

30 December 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
VBViacheslav Borysov
Viacheslav Borysov
OTOleksii Torubara
Oleksii Torubara
VVVadym Volokh
Vadym Volokh
APAnatolii Poliakov
Anatolii Poliakov
MYMykhail Михайлович Yamshinskij
Mykhail Михайлович Yamshinskij
Dmytro Vyktorovych IvanchenkoDmytro Vyktorovych Ivanchenko
Dmytro Vyktorovych Ivanchenko
This paper reports a study into the features of the structural-phase composition of products from the carbon-thermal reduction of scale of high-speed steels that yields an alloying additive. This is necessary to determine the technological parameters that reduce the loss of target elements in the process of obtaining and using resource-saving alloying material. The study indicates that when the degree of scale reduction changed from 28 % to 67 % and 81 %, an increase in the manifestation of a solid solution of carbon and alloying elements in the α-Fe lattice was observed. At the same time, the intensity of the diffraction maxima of FeO and Fe3O4 decreased. In the reduced products, the presence of Fe3C, FeW3C, Fe3W3C, and WC was traced. With an increase in the degree of scale reduction from 28 % to 67 %, the disordered (of "loose" appearance) microstructure was replaced with the formed particles of round and multifaceted shape with different content of alloying elements. At the reduction stage of 81 %, the microstructure had a finely fibrous structure. Based on the suite of studies, the most acceptable degree of reduction of scale of high-speed steel, followed by the use of the obtained material as an alloying additive, is 81 %. At the same time, ensuring the degree of recovery at the level of 67 % would also suffice. This is due to the fact that residual carbon in the form of carbides provides an increased reducing ability and degree of assimilation of alloying elements with the restoration of the residual oxide component in the liquid metal during doping. Spongy microstructure contributes to faster dissolution, in relation to the corresponding standard ferroalloys. This ensures a reduction in the total smelting time and, as a result, a decrease in the energy consumed