This paper investigates the electroosmotic micromixing of non-Newtonian fluid in a microchannel with wall-mounted obstacles and surface potential heterogeneity on the obstacle surface. In the numerical simulation, the full model consisting of the Navier–Stokes equations and the Poisson–Nernst–Plank equations are solved for the electroosmotic fluid field, ion transport, and electric field, and the power law model is used to characterize the rheological behavior of the aqueous solution. The mixing performance is investigated under different parameters, such as electric double layer thickness, flow behavior index, obstacle surface zeta potential, obstacle dimension. Due to the zeta potential heterogeneity at the obstacle surface, vortical flow is formed near the obstacle surface, which can significantly improve the mixing efficiency. The results show that, the mixing efficiency can be improved by increasing the obstacle surface zeta potential, the flow behavior index, the obstacle height, the EDL thickness.
1 March 2019 in Journal of Industrial Integration and Management
Crack initiation and propagation vary the mechanical properties of the asphalt pavement and further alter its designate function. As such, this paper describes a numerical study of a multi-layered strain sensor for the structural health monitoring (SHM) of asphalt pavement. The core of the sensor is an H-shaped Araldite GY-6010 epoxy-based structure with a set of polyvinylidene difluoride (PVDF) piezoelectric transducers in its center beam, which serve as a sensing unit, and a polyurethane foam layer at its external surface which serves as a thermal insulation layer. Sensors are coated with a thin layer of urethane casting resin to prevent the sensor from being corroded by moisture. As a proof-of-concept study, a numerical model is created in COMSOL Multiphysics to simulate the sensor-pavement interaction, in order to design the strain sensor for SHM of asphalt pavement. The results reveal that the optimum thickness of the middle polyurethane foam is 11 mm, with a ratio of the center beam/wing length of 3.2. The simulated results not only validate the feasibility of using the strain sensor for SHM (traffic load monitoring and damage detection), but also to optimize design geometry to increase the sensor sensitivity.
In this paper, a distributed-deflection sensor with a built-in probe is proposed to achieve conformal mechanical measurements of costal cartilage (CC) at its exterior surface. The sensor entails a rectangular sensing-plate integrated with a 5 ×1 transducer array with 0.75mm spatial resolution underneath and a built-in probe of 0.5mm×5mm×3mm above. By pressing the sensor against the exterior surface of a CC tissue with a pre-defined indentation depth pattern, the sensor conforms to the curved tissue surface via the built-in probe first, and then the mechanical properties of the tissue translate to the spatially distributed deflection in the sensor and register as resistance changes by the transducer array. One human Pectus Carinatum (PC) CC sample is measured using the sensor without a built-in probe, and two human PC samples are measured using the sensor with a built-in probe. The comparison in measured results among the three samples validates the capability of the sensor with a built-in probe for conformity to a curved tissue surface in measurements. Based on the recorded relation of average sensor deflection to indentation depth of the two samples measured using the sensor with a built-in probe, the tissue instant indentation modulus and normalized relaxation amount of the two samples are derived and found to vary significantly among the anterior/posterior surfaces and superior/inferior borders at the same position of each sample.
This paper studies the performance of Polyvinylidene fluoride (PVDF)–based strain sensor subject to dynamic loads with different load-moving velocities and the strain sensor’s performance for bottom-up crack detection of an asphalt pavement subject to dynamic loads. The core of the strain sensor is a metalized PVDF sensing film packaged with three protection layers. The encapsulated strain sensor adopts an H-shape to optimize the overall performance. Two numerical models are built in this paper and validate that the voltage output of the PVDF-based strain sensor can well capture the peak lateral strain with the propagation of the bottom-up cracks or the variation of a load moving velocity. Additionally, the sensor has better performance when it is in its lateral alignment position.